Versailles Project on Advanced Materials and Standards interlaboratory study on intensity calibration for x-ray photoelectron spectroscopy instruments using low-density polyethylene.

We report the results of a Versailles Project on Advanced Materials and Standards interlaboratory study on the intensity scale calibration of x-ray photoelectron spectrometers using low-density polyethylene (LDPE) as an alternative material to gold, silver, and copper. An improved set of LDPE reference spectra, corrected for different instrument geometries using a quartz-monochromated Al Kα x-ray source, was developed using data provided by participants in this study. Using these new reference spectra, a transmission function was calculated for each dataset that participants provided. When compared to a similar calibration procedure using the NPL reference spectra for gold, the LDPE intensity calibration method achieves an absolute offset of ∼3.0% and a systematic deviation of ±6.5% on average across all participants. For spectra recorded at high pass energies (≥90 eV), values of absolute offset and systematic deviation are ∼5.8% and ±5.7%, respectively, whereas for spectra collected at lower pass energies (<90 eV), values of absolute offset and systematic deviation are ∼4.9% and ±8.8%, respectively; low pass energy spectra perform worse than the global average, in terms of systematic deviations, due to diminished count rates and signal-to-noise ratio. Differences in absolute offset are attributed to the surface roughness of the LDPE induced by sample preparation. We further assess the usability of LDPE as a secondary reference material and comment on its performance in the presence of issues such as variable dark noise, x-ray warm up times, inaccuracy at low count rates, and underlying spectrometer problems. In response to participant feedback and the results of the study, we provide an updated LDPE intensity calibration protocol to address the issues highlighted in the interlaboratory study. We also comment on the lack of implementation of a consistent and traceable intensity calibration method across the community of x-ray photoelectron spectroscopy (XPS) users and, therefore, propose a route to achieving this with the assistance of instrument manufacturers, metrology laboratories, and experts leading to an international standard for XPS intensity scale calibration.

Development of x-ray reflectivity measurement system under N2 to prevent surface contamination.

In this study, a method to prevent surface contamination on an SiO2 film/Si substrate system was used to improve thickness determination by x-ray reflectometry (XRR). XRR profiles can be significantly affected by the growth of a surface contamination layer, originating from the organic matter present in the measurement environment. An N2 spray method that enables XRR measurement under high-purity N2 has been developed to keep the surface free of contaminants. The method was adopted due to its high applicability to an existing XRR instrument and the ease of system construction. The system mainly consists of an outlet for N2 spray that is positioned in front of the sample and an N2 gas purifier. The high-purity N2 is sprayed on the sample until the measurements are complete. It was revealed that the measured XRR profiles were stable for 115 h, and the evaluated thicknesses were obtained with high reproducibility (±0.05 nm for 10 nm thickness) by adopting the analysis model for clean surfaces.

FTIR-ATR evaluation of organic contaminant cleaning methods for SiO2 surfaces.

The effectiveness of cleaning organic contaminants from silicon dioxide (SiO2) surfaces was studied by conducting highly sensitive measurements using Fourier Transform Infrared Attenuated Total reflectance (FTIR-ATR) with a Si prism as the waveguide. To serve as an example, the surface of the prism was oxidized to an order of a few nanometers. The oxidized Si surface film was allowed to stand in the atmosphere and then wet-cleaned in a repeated manner; subsequently its thickness was measured by ellipsometry. Although, various wet-cleaning methods were tested, they only showed values of 0.1-0.2 nm larger than, but not equal to, the original thickness immediately after oxidation. FTIR-ATR measurements of the spectral change after exposure to air revealed that organic species, such as C-CH3 and -(CH2)n-, increased with time. Wet-cleaning the sample failed to remove the C-CH3 species, which indicates that they corresponded to the film thickness increment from the original.