Stability of Bimetallic PtxRuy - From Model Surfaces to Nanoparticulate Electrocatalysts.

Fundamental research campaigns in electrocatalysis often involve the use of model systems, such as single crystals or magnetron-sputtered thin films (single metals or metal alloys). The downsides of these approaches are that oftentimes only a limited number of compositions are picked and tested (guided by chemical intuition) and that the validity of trends is not verified under operating conditions typically present in real devices. These together can lead to deficient conclusions, hampering the direct application of newly discovered systems in real devices. In this contribution, the stability of magnetron-sputtered bimetallic PtxRuy thin film electrocatalysts (0 at. % to 100 at. % Ru content) along with three commercially available carbon-supported counterparts (50-67 at. % Ru content) was mapped under electrocatalytic conditions in acidic electrolytes using online ICP-MS. We found several differences between the two systems in the amount of metals dissolved along with the development of the morphology and composition. While the Pt-rich PtxRuy compositions remained unchanged, 30-50 nm diameter surface pits were detected in the case of the Ru-rich sputtered thin films. Contrastingly, the surface of the carbon-supported NPs enriched in Pt accompanied by the leaching of a significant amount of Ru from the alloy structure was observed. Change in morphology was accompanied by a mass loss reaching around 1-2 wt % in the case of the sputtered samples and almost 10 wt % for the NPs. Since PtxRuy has prime importance in driving alcohol oxidation reactions, the stability of all investigated alloys was screened in the presence of isopropanol. While Pt dissolution was marginally affected by the presence of isopropanol, several times higher Ru dissolution was detected, especially in the case of the Ru-rich compositions. Our results underline that trends in terms of electrocatalytic activity and stability cannot always be transferred from model samples to systems that are closer to the ones applied in real devices.

Monolithic Two-Terminal Tandem Solar Cells Using Sb2S3 and Solution-Processed PbS Quantum Dots Achieving an Open-Circuit Potential beyond 1.1 V.

Multijunction solar cells have the prospect of a greater theoretical efficiency limit than single-junction solar cells by minimizing the transmissive and thermalization losses a single absorber material has. In solar cell applications, Sb2S3 is considered an attractive absorber due to its elemental abundance, stability, and high absorption coefficient in the visible range of the solar spectrum, yet with a band gap of 1.7 eV, it is transmissive for near-IR and IR photons. Using it as the top cell (the cell where light is first incident) in a two-terminal tandem architecture in combination with a bottom cell (the cell where light arrives second) of PbS quantum dots (QDs), which have an adjustable band gap suitable for absorbing longer wavelengths, is a promising approach to harvest the solar spectrum more effectively. In this work, these two subcells are monolithically fabricated and connected in series by a poly(3,4-ethylene-dioxythiophene) polystyrene sulfonate (PEDOT:PSS)-ZnO tunnel junction as the recombination layer. We explore the surface morphology of ZnO QD films with different spin-coating conditions, which serve as the PbS QD cell's electron transport material. Furthermore, we examine the differences in photogenerated current upon varying the PbS QD absorber layer thickness and the electrical and optical characteristics of the tandem with respect to the stand-alone reference cells. This tandem architecture demonstrates an extended spectral response into the IR with an open-circuit potential exceeding 1.1 V and a power conversion efficiency of 5.6%, which is greater than that of each single-junction cell.

Ultrafast electronic relaxation pathways of the molecular photoswitch quadricyclane.

The light-induced ultrafast switching between molecular isomers norbornadiene and quadricyclane can reversibly store and release a substantial amount of chemical energy. Prior work observed signatures of ultrafast molecular dynamics in both isomers upon ultraviolet excitation but could not follow the electronic relaxation all the way back to the ground state experimentally. Here we study the electronic relaxation of quadricyclane after exciting in the ultraviolet (201 nanometres) using time-resolved gas-phase extreme ultraviolet photoelectron spectroscopy combined with non-adiabatic molecular dynamics simulations. We identify two competing pathways by which electronically excited quadricyclane molecules relax to the electronic ground state. The fast pathway (<100 femtoseconds) is distinguished by effective coupling to valence electronic states, while the slow pathway involves initial motions across Rydberg states and takes several hundred femtoseconds. Both pathways facilitate interconversion between the two isomers, albeit on different timescales, and we predict that the branching ratio of norbornadiene/quadricyclane products immediately after returning to the electronic ground state is approximately 3:2.

Valence shell electronically excited states of norbornadiene and quadricyclane.

The absolute photoabsorption cross sections of norbornadiene (NBD) and quadricyclane (QC), two isomers with chemical formula C7H8 that are attracting much interest for solar energy storage applications, have been measured from threshold up to 10.8 eV using the Fourier transform spectrometer at the SOLEIL synchrotron radiation facility. The absorption spectrum of NBD exhibits some sharp structure associated with transitions into Rydberg states, superimposed on several broad bands attributable to valence excitations. Sharp structure, although less pronounced, also appears in the absorption spectrum of QC. Assignments have been proposed for some of the absorption bands using calculated vertical transition energies and oscillator strengths for the electronically excited states of NBD and QC. Natural transition orbitals indicate that some of the electronically excited states in NBD have a mixed Rydberg/valence character, whereas the first ten excited singlet states in QC are all predominantly Rydberg in the vertical region. In NBD, a comparison between the vibrational structure observed in the experimental 11B1-11A1 (3sa1 ← 5b1) band and that predicted by Franck-Condon and Herzberg-Teller modeling has necessitated a revision of the band origin and of the vibrational assignments proposed previously. Similar comparisons have encouraged a revision of the adiabatic first ionization energy of NBD. Simulations of the vibrational structure due to excitation from the 5b2 orbital in QC into 3p and 3d Rydberg states have allowed tentative assignments to be proposed for the complex structure observed in the absorption bands between ∼5.4 and 7.0 eV.

Understanding the light induced hydrophilicity of metal-oxide thin films.

Photocatalytic effects resulting in water splitting, reduction of carbon dioxide to fuels using solar energy, decomposition of organic compounds, and light-induced hydrophilicity observed on surfaces of various metal oxides (MOx), all rely on the same basic physical mechanisms, and have attracted considerable interest over the past decades. TiO2 and ZnO, two natively n-type doped wide bandgap semiconductors exhibit the effects mentioned above. In this study we propose a model for the photo-induced hydrophilicity in MOx films, and we test the model for TiO2/Si and ZnO/Si heterojunctions. Experimentally, we employ a wet exposure technique whereby the MOx surface is exposed to UV light while a water droplet is sitting on the surface, which allows for a continuous recording of contact angles during illumination. The proposed model and the experimental techniques allow a determination of minority carrier diffusion lengths by contact angle measurements and suggest design rules for materials exhibiting photocatalytic hydrophilicity. We expect that this methodology can be extended to improve our physical understanding of other photocatalytic surface effects.

A Mild Method for the Activation of Cation Exchange Membranes Used in Tubular PEM Electrolyzers.

Co-extrusion of both half-cells in tubular PEM water electrolyzers can lower the costs for hydrogen production, since the number of components is reduced and the production process is simplified. However, after co-extrusion of the inner half-cell and the ion exchange membrane, the membrane is in its fluoride sulfonyl form and must be hydrolyzed to achieve the proton conductive sulfonic acid to be ready for use. Common practice is the hydrolysis using concentrated alkaline solutions, which causes a corrosion of the laminated anode electrode. We developed a less corrosive method using triethylsilanol as reactant. Tubular membranes hydrolyzed with this new procedure were characterized and tested in an electrolyzer laboratory test setup.

Synergistic Combination of Reductive Covalent Functionalization and Atomic Layer Deposition-Towards Spatially Defined Graphene-Organic-Inorganic Heterostructures.

Three-dimensionally (3D) well-ordered and highly integrated graphene hybrid architectures are considered to be next-generation multifunctional graphene materials but still remain elusive. Here, we report the first realization of unprecedented 3D-patterned graphene nano-ensembles composed of a graphene monolayer, a tailor-made structured organophenyl layer, and three metal oxide films, providing the first example of such a hybrid nano-architecture. These spatially resolved and hierarchically structured quinary hybrids are generated via a two-dimensional (2D)-functionalization-mediated atomic layer deposition growth process, involving an initial lateral molecular programming of the graphene lattice via lithography-assisted 2D functionalization and a subsequent stepwise molecular assembly in these regions in the z-direction. Our breakthrough lays the foundation for the construction of emerging 3D-patterned graphene heterostructures.

GD-OES Investigations of Lithium-Ion Battery Graphite Anodes: Impact of Plasma Parameters and Electrode Properties.

Due to the demand of lithium-ion battery investigations with glow discharge optical emission spectroscopy (GD-OES), a fundamental study of the influence of essential GD-OES parameters toward graphite anodes in an argon plasma was conducted and compared to previous investigations of massive materials. It is shown that increased applied voltage (500-700 V) enhances the sputtering rate by up to 100%/100 V while keeping the crater shape unaffected. In contrast to this, gas pressure variation seems to be the main tool for crater shape adjustment. Enhancement of the gas pressure (160-300 Pa) pushes the crater profile from a concave to flat shape and to concave again. Known plasma effects are discussed and correlated with the observations. A set of measuring parameters providing a good balance between the crater shape and the sputtering rate is proposed. Additionally, an increase of the duty cycle in the pulsed glow discharge mode leads to a linear increase of the sputtering rate, while a pulse duration rise enhances the sputtering rate in a nonlinear fashion. Thus, different pulsing conditions represent instruments for enhancement of the sputtering rate without affecting the crater shape significantly. Our investigation of different electrode densities shows that lower densities lead to a larger sputtered volume as well as a larger concavity of the released crater.

Nature-inspired functional porous materials for low-concentration biomarker detection.

Nanostructuration is a promising tool for enhancing the performance of sensors based on electrochemical transduction. Nanostructured materials allow for increasing the surface area of the electrode and improving the limit of detection (LOD). In this regard, inverse opals possess ideal features to be used as substrates for developing sensors, thanks to their homogeneous, interconnected pore structure and the possibility to functionalize their surface. However, overcoming the insulating nature of conventional silica inverse opals fabricated via sol-gel processes is a key challenge for their application as electrode materials. In this work, colloidal assembly, atomic layer deposition and selective surface functionalization are combined to design conductive inverse opals as an electrode material for novel glucose sensing platforms. An insulating inverse opal scaffold is coated with uniform layers of conducting aluminum zinc oxide and platinum, and subsequently functionalized with glucose oxidase embedded in a polypyrrole layer. The final device can sense glucose at concentrations in the nanomolar range and is not affected by the presence of common interferents gluconolactone and pyruvate. This method may also be applied to different conductive materials and enzymes to generate a new class of highly efficient biosensors.

Direct-Patterning ZnO Deposition by Atomic-Layer Additive Manufacturing Using a Safe and Economical Precursor.

Area-selective atomic layer deposition (AS-ALD) is a bottom-up nanofabrication method delivering single atoms from a molecular precursor. AS-ALD enables self-aligned fabrication and outperforms lithography in terms of cost, resistance, and equipment prerequisites, but it requires pre-patterned substrates and is limited by insufficient selectivity and finite choice of substrates. These challenges are circumvented by direct patterning with atomic-layer additive manufacturing (ALAM) - a transfer of 3D-printing principles to atomic-layer manufacturing where a precursor supply nozzle enables direct patterning instead of blanket coating. The reduced precursor vapor consumption in ALAM as compared with ALD calls for the use of less volatile precursors by replacing diethylzinc used traditionally in ALD with bis(dimethylaminopropyl)zinc, Zn(DMP)2 . The behavior of this novel ZnO ALAM process follows that of the corresponding ALD in terms of deposit quality and growth characteristics. The temperature window for self-limiting growth of stoichiometric, crystalline material is 200-250 °C. The growth rates are 0.9 Å per cycle in ALD (determined by spectroscopic ellipsometry) and 1.1 Å per pass in ALAM (imaging ellipsometry). The preferential crystal orientation increases with temperature, while energy-dispersive X-ray spectroscopic and XPS show that only intermediate temperatures deliver stoichiometric ZnO. A functional thin-film transistor is created from an ALAM-deposited ZnO line and characterized.

Mechanistic Insight into Solution-Based Atomic Layer Deposition of CuSCN Provided by In Situ and Ex Situ Methods.

Solution-based atomic layer deposition (sALD) processes enable the preparation of thin films on nanostructured surfaces while controlling the film thickness down to a monolayer and preserving the homogeneity of the film. In sALD, a similar operation principle as in gas-phase ALD is used, however, with a broader range of accessible materials and without requiring expensive vacuum equipment. In this work, a sALD process was developed to prepare CuSCN on a Si substrate using the precursors CuOAc and LiSCN. The film growth was studied by ex situ atomic force microscopy (AFM), analyzed by a neural network (NN) approach, ellipsometry, and a newly developed in situ infrared (IR) spectroscopy experiment in combination with density functional theory (DFT). In the self-limiting sALD process, CuSCN grows on top of an initially formed two-dimensional (2D) layer as three-dimensional spherical nanoparticles with an average size of ∼25 nm and a narrow particle size distribution. With increasing cycle number, the particle density increases and larger particles form via Ostwald ripening and coalescence. The film grows preferentially in the ß-CuSCN phase. Additionally, a small fraction of the α-CuSCN phase and defect sites form.

Preparation of geometrically highly controlled Ga particle arrays on quasi-planar nanostructured surfaces as a SCALMS model system.

This study establishes a preparative route towards a model system for supported catalytically active liquid metal solutions (SCALMS) on nanostructured substrates. This model is characterized by a uniquely precise geometrical control of the gallium particle size distribution. In a SCALMS system, the Ga serves as a matrix material which can be decorated with a catalytically active material subsequently. The corresponding Ga containing precursor is spin-coated on aluminum based substrates, previously nanostructured by electrochemical anodization. The highly ordered substrates are functionalized with distinct oxide coatings by atomic layer deposition (ALD) independently from the morphology. After preparation of the metal particles on the oxide interface, the characterization of our model system in terms of its geometry parameters (droplet diameter, size distribution and population density) points to SiO2 as the best suited surface for a highly controlled geometry. This flexible model system can be functionalized with a dissolved noble metal catalyst for the application chosen.

Current status of carbon monoxide dehydrogenases (CODH) and their potential for electrochemical applications.

Anthropogenic carbon dioxide (CO2) levels are rising to alarming concentrations in earth's atmosphere, causing adverse effects and global climate changes. In the last century, innovative research on CO2 reduction using chemical, photochemical, electrochemical and enzymatic approaches has been addressed. In particular, natural CO2 conversion serves as a model for many processes and extensive studies on microbes and enzymes regarding redox reactions involving CO2 have already been conducted. In this review we focus on the enzymatic conversion of CO2 to carbon monoxide (CO) as the chemical conversion downstream of CO production render CO particularly attractive as a key intermediate. We briefly discuss the different currently known natural autotrophic CO2 fixation pathways, focusing on the reversible reaction of CO2, two electrons and protons to CO and water, catalyzed by carbon monoxide dehydrogenases (CODHs). We then move on to classify the different type of CODHs, involved catalyzed chemical reactions and coupled metabolisms. Finally, we discuss applications of CODH enzymes in photochemical and electrochemical cells to harness CO2 from the environment transforming it into commodity chemicals.

Solution Atomic Layer Deposition of Smooth, Continuous, Crystalline Metal-Organic Framework Thin Films.

For the first time, a procedure has been established for the growth of surface-anchored metal-organic framework (SURMOF) copper(II) benzene-1,4-dicarboxylate (Cu-BDC) thin films of thickness control with single molecule accuracy. For this, we exploit the novel method solution atomic layer deposition (sALD). The sALD growth rate has been determined at 4.5 Å per cycle. The compact and dense SURMOF films grown at room temperature by sALD possess a vastly superior film thickness uniformity than those deposited by conventional solution-based techniques, such as dipping and spraying while featuring clear crystallinity from 100 nm thickness. The highly controlled layer-by-layer growth mechanism of sALD proves crucial to prevent unwanted side reactions such as Ostwald ripening or detrimental island growth, ensuring continuous Cu-BDC film coverage. This successful demonstration of sALD-grown compact continuous Cu-BDC SURMOF films is a paradigm change and provides a key advancement enabling a multitude of applications that require continuous and ultrathin coatings while maintaining tight film thickness specifications, which were previously unattainable with conventional solution-based growth methods.

A Geometrically Well-Defined and Systematically Tunable Experimental Model to Transition from Planar to Mesoporous Perovskite Solar Cells.

A series of perovskite solar cells with systematically varying surface area of the interface between n-type electron conducting layer (TiO2) and perovskite are prepared by using an ordered array of straight, cylindrical nanopores generated by anodizing an aluminum layer evaporated onto a transparent conducting electrode. A series of samples with pore length varied from 100 to 500 nm are compared to each other and complemented by a classical planar cell and a mesoporous counterpart. All samples are characterized in terms of morphology, chemistry, optical properties, and performance. All samples absorb light to the same degree, and the increased interface area does not generate enhanced recombination. However, the short circuit current density increases monotonically with the specific surface area, indicating improved charge extraction efficiency. The importance of the slow interfacial rearrangement of ions associated with planar perovskite cells is shown to decrease in a systematic manner as the interfacial surface area increases. The results demonstrate that planar and mesoporous cells obey to the same physical principles and differ from each other quantitatively, not qualitatively. Additionally, the study shows that a significantly lower TiO2 surface area compared to mesoporous TiO2 is needed for an equal charge extraction.

Molecular Stacking on Graphene.

The sequential vertical polyfunctionalization of 2D addend-patterned graphene is still elusive. Here, we report a practical realization of this goal via a "molecular building blocks" approach, which is based on a combination of a lithography-assisted reductive functionalization approach and a post-functionalization step to sequentially and controllably link the molecular building blocks ethylpyridine, cis-dichlorobis(2,2'-bipyridyl)ruthenium, and triphenylphosphine (4-methylbenzenethiol, respectively) on selected lattice regions of a graphene matrix. The assembled 2D hetero-architectures are unambiguously characterized by various spectroscopic and microscopic measurements, revealing the stepwise stacking of the molecular building blocks on the graphene surface. Our method overcomes the current limitation of a one-layer-only binding to the graphene surface and opens the door for a vertical growth in the z-direction.

Femtosecond Laser Assisted 3D Etching Using Inorganic-Organic Etchant.

Selective laser etching (SLE) is a technique that allows the fabrication of arbitrarily shaped glass micro-objects. In this work, we show how the capabilities of this technology can be improved in terms of selectivity and etch rate by applying an etchant solution based on a Potassium Hydroxide, water, and isopropanol mixture. By varying the concentrations of these constituents, the wetting properties, as well as the chemical reaction of fused silica etching, can be changed, allowing us to achieve etching rates in modified fused silica up to 820 µm/h and selectivity up to ∼3000. This is used to produce a high aspect ratio (up to 1:1000), straight and spiral microfluidic channels which are embedded inside a volume of glass. Complex 3D glass micro-structures are also demonstrated.

Additive Manufacturing in Atomic Layer Processing Mode.

Additive manufacturing (3D printing) has not been applicable to micro- and nanoscale engineering due to the limited resolution. Atomic layer deposition (ALD) is a technique for coating large areas with atomic thickness resolution based on tailored surface chemical reactions. Thus, combining the principles of additive manufacturing with ALD could open up a completely new field of manufacturing. Indeed, it is shown that a spatially localized delivery of ALD precursors can generate materials patterns. In this "atomic-layer additive manufacturing" (ALAM), the vertical resolution of the solid structure deposited is about 0.1 nm, whereas the lateral resolution is defined by the microfluidic gas delivery. The ALAM principle is demonstrated by generating lines and patterns of pure, crystalline TiO2 and Pt on planar substrates and conformal coatings of 3D nanostructures. The functional quality of ALAM patterns is exemplified with temperature sensors, which achieve a performance similar to the industry standard. This general method of multimaterial direct patterning is much simpler than standard multistep lithographic microfabrication. It offers process flexibility, saves processing time, investment, materials, waste, and energy. It is envisioned that together with etching, doping, and cleaning performed in a similar local manner, ALAM will create the "atomic-layer advanced manufacturing" family of techniques.

From Sticky to Slippery: Self-Functionalizing Lubricants for In Situ Fabrication of Liquid-Infused Surfaces.

Liquid-infused surfaces offer a versatile approach to create self-cleaning coatings. In such coatings, a thin film of a fluid lubricant homogeneously coats the substrate and thus prevents direct contact with a second, contaminating liquid. For stable repellency, the interfacial energies need to be controlled to ensure that the lubricant is not replaced by the contaminating liquid. Here, we introduce the concept of self-functionalizing lubricants. Functional molecular species that chemically match the lubricant but possess selective anchor groups are dissolved in the lubricant and self-adhere to the surface, forming the required surface chemistry in situ from within the applied lubricant layer. To add flexibility to the self-functionalizing concept, the substrate is first primed with a thin polydopamine base layer, which can be deposited to nearly any substrate material from aqueous solutions and retains reactivity toward electron-donating groups such as amines. The temporal progression of the in situ functionalization is investigated by ellipsometry and quartz crystal microbalance and correlated to macroscopic changes in contact angle and contact angle hysteresis. The flexibility of the approach is underlined by creating repellent coatings with various substrate/lubricant combinations. The prepared liquid-infused surfaces significantly reduce cement adhesion and provide easy-to-clean systems under real-world conditions on shoe soles.