Importance of using complementary process analyzers for the process monitoring, analysis, and understanding of freeze drying.

The aim of the present paper is to demonstrate the importance of using complementary process analyzers (PAT tools) for the process monitoring, analysis, and understanding of freeze drying. A mannitol solution was used as a model system. Raman spectroscopic, near-infrared (NIR) spectroscopic, plasma emission spectroscopic, and wireless temperature measurements (TEMPRIS) were simultaneously performed in-line and real-time during each freeze-drying experiment. The combination of these four process analyzers to monitor a freeze-drying process is unique. The Raman and NIR data were analyzed using principal component analysis (PCA) and multivariate curve resolution (MCR), while the plasma emission spectroscopic and wireless temperature measurement data were analyzed using univariate data analysis. It was shown that the considered process analyzers do not only complement but also mutually confirm each other with respect to process step end points, physical phenomena occurring during freeze drying (process understanding), and product characterization (solid state). Furthermore and most important, the combined use of the process analyzers helped to identify flaws in previous studies in which these process analyzers were studied individually. Process analyzers might wrongly indicate that some process steps are fulfilled. Finally, combining the studied process analyzers also showed that more information per process analyzer can be obtained than previously described. A combination of Raman and plasma emission spectroscopy seems favorable for the monitoring of nearly all critical freeze-drying process aspects.

In-line and real-time process monitoring of a freeze drying process using Raman and NIR spectroscopy as complementary process analytical technology (PAT) tools.

The aim of the present study was to examine the complementary properties of Raman and near infrared (NIR) spectroscopy as PAT tools for the fast, noninvasive, nondestructive and in-line process monitoring of a freeze drying process. Therefore, Raman and NIR probes were built in the freeze dryer chamber, allowing simultaneous process monitoring. A 5% (w/v) mannitol solution was used as model for freeze drying. Raman and NIR spectra were continuously collected during freeze drying (one Raman and NIR spectrum/min) and the spectra were analyzed using principal component analysis (PCA) and multivariate curve resolution (MCR). Raman spectroscopy was able to supply information about (i) the mannitol solid state throughout the entire process, (ii) the endpoint of freezing (endpoint of mannitol crystallization), and (iii) several physical and chemical phenomena occurring during the process (onset of ice nucleation, onset of mannitol crystallization). NIR spectroscopy proved to be a more sensitive tool to monitor the critical aspects during drying: (i) endpoint of ice sublimation and (ii) monitoring the release of hydrate water during storage. Furthermore, via NIR spectroscopy some Raman observations were confirmed: start of ice nucleation, end of mannitol crystallization and solid state characteristics of the end product. When Raman and NIR monitoring were performed on the same vial, the Raman signal was saturated during the freezing step caused by reflected NIR light reaching the Raman detector. Therefore, NIR and Raman measurements were done on a different vial. Also the importance of the position of the probes (Raman probe above the vial and NIR probe at the bottom of the sidewall of the vial) in order to obtain all required critical information is outlined. Combining Raman and NIR spectroscopy for the simultaneous monitoring of freeze drying allows monitoring almost all critical freeze drying process aspects. Both techniques do not only complement each other, they also provided mutual confirmation of specific conclusions.

Raman spectroscopy as a process analytical technology (PAT) tool for the in-line monitoring and understanding of a powder blending process.

The aim of this study is to propose a strategy to implement a PAT system in the blending step of pharmaceutical production processes. It was examined whether Raman spectroscopy can be used as PAT tool for the in-line and real-time endpoint monitoring and understanding of a powder blending process. A screening design was used to identify and understand the significant effects of two process variables (blending speed and loading of the blender) and of a formulation variable (concentration of active pharmaceutical ingredient (API): diltiazem hydrochloride) upon the required blending time (response variable). Interactions between the variables were investigated as well. A Soft Independent Modelling of Class Analogy (SIMCA) model was developed to determine the homogeneity of the blends in-line and real-time using Raman spectroscopy in combination with a fiber optical immersion probe. One blending experiment was monitored using Raman and NIR spectroscopy simultaneously. This was done to verify whether two independent monitoring tools can confirm each other's endpoint conclusions. The analysis of the experimental design results showed that the measured endpoints were excessively rounded due to the large measurement intervals relative to the first blending times. This resulted in effects and critical effects which cannot be interpreted properly. To be able to study the effects properly, the ratio between the blending times and the measurement intervals should be sufficiently high. In this study, it anyway was demonstrated that Raman spectroscopy is a suitable PAT tool for the endpoint control of a powder blending process. Raman spectroscopy not only allowed in-line and real-time monitoring of the blend homogeneity, but also helped to understand the process better in combination with experimental design. Furthermore, the correctness of the Raman endpoint conclusions was demonstrated for one process by using a second independent endpoint monitoring tool (NIR spectroscopy). Hence, the use of two independent techniques for the control of one response variable not only means a mutual confirmation of both methods, but also provides a higher certainty in the determined endpoint.

Implementation of a process analytical technology system in a freeze-drying process using Raman spectroscopy for in-line process monitoring.

The aim of the present study was to propose a strategy for the implementation of a Process Analytical Technology system in freeze-drying processes. Mannitol solutions, some of them supplied with NaCl, were used as models to freeze-dry. Noninvasive and in-line Raman measurements were continuously performed during lyophilization of the solutions to monitor real time the mannitol solid state, the end points of the different process steps (freezing, primary drying, secondary drying), and physical phenomena occurring during the process. At-line near-infrared (NIR) and X-ray powder diffractometry (XRPD) measurements were done to confirm the Raman conclusions and to find out additional information. The collected spectra during the processes were analyzed using principal component analysis and multivariate curve resolution. A two-level full factorial design was used to study the significant influence of process (freezing rate) and formulation variables (concentration of mannitol, concentration of NaCl, volume of freeze-dried sample) upon freeze-drying. Raman spectroscopy was able to monitor (i) the mannitol solid state (amorphous, alpha, beta, delta, and hemihydrate), (ii) several process step end points (end of mannitol crystallization during freezing, primary drying), and (iii) physical phenomena occurring during freeze-drying (onset of ice nucleation, onset of mannitol crystallization during the freezing step, onset of ice sublimation). NIR proved to be a more sensitive tool to monitor sublimation than Raman spectroscopy, while XRPD helped to unravel the mannitol hemihydrate in the samples. The experimental design results showed that several process and formulation variables significantly influence different aspects of lyophilization and that both are interrelated. Raman spectroscopy (in-line) and NIR spectroscopy and XRPD (at-line) not only allowed the real-time monitoring of mannitol freeze-drying processes but also helped (in combination with experimental design) us to understand the process.

Raman spectroscopic method for the determination of medroxyprogesterone acetate in a pharmaceutical suspension: validation of quantifying abilities, uncertainty assessment and comparison with the high performance liquid chromatography reference method.

An alternative fast and non-destructive validated Raman spectroscopic analytical procedure, requiring no sample preparation, was compared with the industrially applied HPLC reference method (Pfizer Manufacturing Belgium) for the quantitative determination of medroxyprogesterone acetate (MPA) in DepoProvera suspensions (150 mg mL(-1), Pfizer). The Raman calibration model was developed by plotting the peak intensity of the baseline-corrected and normalized spectral band (corrected by external standard measurements) between 1595 and 1620 cm(-1) against known MPA concentrations in standards. At this band, no spectral interferences from the suspension medium are observed. The most suitable model for the calibration data (straight line or higher order polynomial) was determined by evaluating the fit and predictive properties of the models. In a second step, the developed Raman spectroscopic analytical method was validated by calculating the accuracy profile on the basis of the analysis results of validation samples. Furthermore, based on the data of the accuracy profile, the measurement uncertainty was determined. Finally, as the aim of the alternative method is to replace the destructive, time-consuming HPLC method, requiring sample preparation, it needs to be demonstrated that the new Raman method performs at least as good as the HPLC method. Therefore, the performance (precision and bias) of both methods was compared. A second order polynomial calibration curve through the calibration data supplies the best predictive properties and gives an acceptable fit. From the accuracy profile, it was concluded that at the target concentration (150 mg mL(-1)), 95 out 100 future routine measurements will be included within the acceptance limits (5%). Comparison of the alternative method with the reference method at the target concentration indicates that the Raman method performs at least as good as the HPLC method for precision (repeatability and intermediate precision) and bias. The fast and non-destructive Raman method hence provides an alternative for the destructive and time-consuming HPLC procedure.

Influence of particle size on the quantitative determination of salicylic acid in a pharmaceutical ointment using FT-Raman spectroscopy.

A second order polynomial calibration model was developed and statistically validated for the direct and non-destructive quantitative analysis - without sample preparation - of the active pharmaceutical ingredient (API) salicylic acid in a pharmaceutical ointment using FT-Raman spectroscopy. The calibration curve was modeled by plotting the peak intensity of the vector normalized spectral band between 757 and 784cm(-1) against the known salicylic acid concentrations in standards. At this band, no spectral interferences from the ointment vehiculum (white vaseline) are observed. For the validation of the polynomial model, its fit and its predictive properties were evaluated. The validated model was used for the quantification of 25 ointments, compounded by different retail pharmacists. The same standards and samples were used, both for development and validation of a regression model and for quantitative determination by HPLC - with sample preparation - as described for the related substances of salicylic acid in the Ph. Eur. IV. The quantification results obtained by the FT-Raman method corresponded with the HPLC results (p=0.22), provided that the particle size of salicylic acid in the standards is the same as in the analyzed samples. The non-destructive FT-Raman method is a reliable alternative for the destructive HPLC method, as it is faster and does not require sample pre-treatment procedures.

Raman spectroscopy as a process analytical technology tool for the understanding and the quantitative in-line monitoring of the homogenization process of a pharmaceutical suspension.

The aim of this study was to propose a Process Analytical Technology (PAT) strategy for the quantitative in-line monitoring of an aqueous pharmaceutical suspension using Raman spectroscopy. A screening design was used to study the significance of process variables (mixing speed and height of the stirrer in the reactor) and of formulation variables (concentration of the active pharmaceutical ingredient (API) ibuprofen and the viscosity enhancer (xanthan gum)) on the time required to homogenize an aqueous pharmaceutical model suspension as response variable. Ibuprofen concentration (10% and 15% (w/v)) and the height of stirrer (position 1 and 2) were discrete variables, whereas the viscosity enhancer (concentration range: 1-2 g L-1) and the mixing speed (700-1000 rpm) were continuous variables. Next, a multilevel full factorial design was applied to study the effect of the remaining significant variables upon the homogenization process and to establish the optimum conditions for the process. Interactions between these variables were investigated as well. During each design experiment, the conformity index (CI) method was used to monitor homogeneity of the suspension mixing system in real-time using Raman spectroscopy in combination with a fibre optical immersion probe. Finally, a principal component regression (PCR) model was developed and evaluated to perform quantitative real-time and in-line measurements of the API during the mixing process. The experimental design results showed that the suspension homogenization process is an irregular process, for which it is impossible to model the studied variables upon the measured response variable. However, applying the PCR model it is possible to predict in-line and real-time the concentration of the API in a suspension during a mixing process. In this study, it is shown that Raman spectroscopy is a suitable PAT tool for the control of the homogenization process of an aqueous suspension. Raman spectroscopy not only allowed real-time monitoring of the homogeneity of the suspension, but also helped (in combination with experimental design) to understand the process. Further, the technique allowed real-time and in-line quantification of the API during the mixing process.

Development and validation of a direct, non-destructive quantitative method for medroxyprogesterone acetate in a pharmaceutical suspension using FT-Raman spectroscopy.

A simple linear regression method was developed and statistically validated for the direct and non-destructive quantitative analysis--without sample preparation--of the active pharmaceutical ingredient (API) medroxyprogesterone acetate (MPA) in an aqueous pharmaceutical suspension (150 mg in 1.0 ml) using FT-Raman spectroscopy. The linear regression was modelled by plotting the highest peak intensity of the vector normalized spectral band between 1630 and 1590 cm-1 against different MPA standard suspension concentrations. At this band, no spectral interferences from additives in the suspension are observed. The validated model was used for the quantification of a commercial suspension (150 mg in 1.0 ml) of the commercialized preparations. The same standards and samples were used, respectively, for the development and validation of a simple linear regression model and for the quantitative determination by means of HPLC-with sample preparation-as described for the related substances of MPA in the Ph. Eur. IV. The quantification results obtained by the FT-Raman method corresponded with the claimed label concentration (150.01+/-0.96 mg/ml (n=6)). Applying the HPLC method, however, a systematic error was observed (157.77+/-0.94 mg/ml (n=6)). The direct FT-Raman method hence appears the most reliable for the quantification of the MPA component in suspension, compared to the HPLC method that requires sample preparation. The latter method provides a systematic error because the exact volume or density of a suspension sample is unknown. A precise isolation of fixed volumes from a suspension is rather unfeasible because of the continuous sagging of the suspended particles and their sticking to the used materials in the isolation process.

Review: HPLC determination of fumonisin mycotoxins.

An overview of liquid chromatographic methods, mainly employing fluorescence detection together with sample pre-treatment methods, is presented for the determination of the toxic group of fumonisin mycotoxins in various matrices.

In-line monitoring of a pharmaceutical blending process using FT-Raman spectroscopy.

FT-Raman spectroscopy (in combination with a fibre optic probe) was evaluated as an in-line tool to monitor a blending process of diltiazem hydrochloride pellets and paraffinic wax beads. The mean square of differences (MSD) between two consecutive spectra was used to identify the time required to obtain a homogeneous mixture. A traditional end-sampling thief probe was used to collect samples, followed by HPLC analysis to verify the Raman data. Large variations were seen in the FT-Raman spectra logged during the initial minutes of the blending process using a binary mixture (ratio: 50/50, w/w) of diltiazem pellets and paraffinic wax beads (particle size: 800-1200 microm). The MSD-profiles showed that a homogeneous mixture was obtained after about 15 min blending. HPLC analysis confirmed these observations. The Raman data showed that the mixing kinetics depended on the particle size of the material and on the mixing speed. The results of this study proved that FT-Raman spectroscopy can be successfully implemented as an in-line monitoring tool for blending processes.

Quantitative determination of p-aminosalicylic acid and its degradation product m-aminophenol in pellets by ion-pair high-performance liquid chromatography applying the monolithic Chromolith Speedrod RP-18e column.

An ion-pair high performance liquid chromatographic method was developed for the simultaneous determination of p-aminosalicylic acid (PAS) and its degradation product m-aminophenol (MAP) in a newly developed multiparticular drug delivery system. Owing to the concentration differences of PAS and MAP, acetanilide and sulfanilic acid were used as internal standards, respectively. The separation was performed on a Chromolith SpeedROD RP-18e column, a new packing material consisting of monolithic rods of highly porous silica. The mobile phase composition was of 20 mm phosphate buffer, 20 mm tetrabutylammonium hydrogen sulphate and 16% (v/v) methanol adjusted to pH 6.8, at a flow-rate of 1.0 mL/min, resulting in a run-time of about 6 min. Detection was by UV at 233 nm. The method was validated and proved to be useful for stability testing of the new dosage form. Separation efficiency was compared between the new packing material Chromolith SpeedROD RP-18e and the conventional reversed-phase cartridge LiChroCART 125-4 (5 microm). A robustness test was carried out on both columns and different separation parameters (retention, resolution, run time, temperature) were determined.

Application of an alkyl-diol silica precolumn in a column-switching system for the determination of meloxicam in plasma.

The group of LiChrospher alkyl-diol silica (ADS) phases that make part of the unique family of restricted-access materials, have been developed as special packings used in the liquid chromatographic integrated sample processing of biofluids. The advantage of these phases lies in the possibility of direct injection of untreated plasma. An on-line elimination of the protein matrix is achieved with a quantitative recovery together with an on-column enrichment. The present method describes a hand-operated on-line switching high-performance liquid chromatographic system for the determination of meloxicam. Spiked plasma samples were introduced on the ADS precolumn using a 0.05 M phosphate buffer, pH 6.0. After washing with the buffer the ADS column was backflushed with the mobile phase 0.05 M phosphate buffer-30% (v/v) acetonitrile (ACN)-25 mM t-butylamine (TBA) at a pH of 7.0, thus transferring the analyte to the analytical column LiChrocart 125-4 LiChrospher RP-8. The eluent was monitored by a UV-detector set at 364 nm. The developed column-switching method is fully applicable to plasma injections.

Comparison of morphine and hydromorphone analysis on reversed phase columns with different diameters.

A comparison of a reversed phase high-performance liquid chromatographic (HPLC) method performed on columns with different internal diameters is reported for the quantitative routine determination of morphine.HCl and hydromorphone.HCl in solutions used for intramuscular injection. The method is based on the ion-pairing properties of sodium dodecyl sulphate (SDS) with alkaloids on a reversed phase LiChrospher RP-18 packing material and UV-detection at 230 nm. The mobile phase consisted of an acetonitrile: water mixture 35:65 (v/v) containing 0.5% (w/v) SDS and 0.4% (v/v) acetic acid. Precision, linearity and limit of detection were compared on the 2, 3 and 4 mm i.d. x 125 mm columns. A robustness test for the determination of hydromorphone.HCl was also evaluated.

Enantiomeric separation of beta-blockers by HPLC using (R)-1-naphthylglycine and 3,5-dinitrobenzoic acid as chiral stationary phase.

Direct liquid chromatographic separations of the enantiomers of metoprolol and bisoprolol have been developed, using (R)-1-naphthylglycine and 3,5-dinitrobenzoic acid as chiral stationary phase (CSP). The separations were achieved in a normal phase system employing a mobile phase containing n-hexane, 1,2-dichloroethane and methanol. Column efficiency was strongly dependent on the composition of the mobile phase. The eluent contents of methanol and of 1,2-dichloroethane were optimized, and so was flow-rate and column temperature. Under the optimal conditions, linear responses for (R)-metoprolol and (S)-metoprolol are obtained in the range of 0.079-1.38 and 0.015-5.80 mg/ml, with detection limits of 0.008 and 0.002 mg/ml, respectively. As for bisoprolol, the linear ranges of (R)-isomer and (S)-isomer are 0.05-1.31 and 0.02-1.00 mg/ml with detection limits of 0.001 and 0.008 mg/ml, respectively. The relative standard deviation (R.S.D.) of each enantiomer did not exceed 0.90%. The method has been successfully applied to the determination of enantiomers in pharmaceuticals.

Quimioluminiscencia: una interesante alternativapara la detección analítica en sistemas de flujo / Unfamiliar though exciting analytical detection in flowing streams: chemiluminescence

El estudio del tipo de interacción involucrada en la formación de dispersiones sólidas de tolbutamida con distintas proporciones de acetamida y propianamida, ha requerido del diseño y validación de un método analítico por cromatografía líquida de alta eficacia (CLAE) que permita cuantificar la proporción de los transportadores en mezclas físicas y en dispersión sólida. El método resultó ser lineal, preciso y exacto en el intervalo de concentración de 100-1,56 µg/mL para tolbutamida y 50-0,781 µg/mL para acetamida y propianamida (AU)