Electrocatalytic Glycerol Conversion: A Low-Voltage Pathway to Efficient Carbon-Negative Green Hydrogen and Value-Added Chemical Production.

Electrochemical glycerol oxidation reaction (GLYOR) could be a promising way to use the abundantly available glycerol for production of value-added chemicals and fuels. Completely avoiding the oxygen evolution reaction (OER) with GLYOR is an evolving strategy to reduce the overall cell potential and generate value-added chemicals and fuels on both the anode and cathode. We demonstrate the morphology-controlled palladium nanocrystals, afforded by colloidal chemistry, and their established morphology-dependent GLYOR performance. Although it is known that controlling the morphology of an electrocatalyst can modulate the activity and selectivity of the products, still it is a relatively underexplored area for many reactions, including GLYOR. Among nanocube (Pd-NC), truncated octahedron (Pd-TO), spherical and polycrystalline (Pd-PC) morphologies, the Pd-NC electrocatalyst deposited on a Ni foam exhibits the highest glycerol conversion (85%) along with 42% glyceric acid selectivity at a low applied potential of 0.6 V (vs reversible hydrogen electrode (RHE)) in 0.1 M glycerol and 1 M KOH at ambient temperature. Owing to the much favorable thermodynamics of GLYOR on the Pd-NC surface, the assembled electrolyzer requires an electricity input of only ∼3.7 kWh/m3 of H2 at a current density of 100 mA/cm2, in contrast to the requirement of ≥5 kWh/m3 of H2 with an alkaline/PEM electrolyzer. Sustainability has been successfully demonstrated at 10 and 50 mA/cm2 and up to 120 h with GLYOR in water and simulated seawater.

Nanostructured Co-doped BiVO4 for efficient and sustainable photoelectrochemical chlorine evolution from simulated sea-water.

The co-production of hydrogen and chlorine from sea-water splitting could be a potential, sustainable and attractive route by any method. However, challenges to overcome are many, and critically, the sustainability and operating potential of the electrocatalyst are important. In this work, we report on Co-doping in the BiVO4 (Co-BV) crystal lattice and employed the same as the photoanode; Co-BV exhibits a photocurrent of 190 µA cm-2 at 1.1 V vs. RHE (the reversible hydrogen electrode) in the acidic sodium chloride solution (pH 2.3) under one sun illumination. The best-performing photoanode, with 0.05 mol% of Co doping (0.05 Co-BV), selectively produced active chlorine with 92% faradaic efficiency at 1.1 V vs. RHE by successfully suppressing the kinetically sluggish oxygen evolution reaction (OER) and the stability of the catalyst was demonstrated for up to 20 h. This is the lowest operating potential reported for the chlorine evolution reaction (CER), thus far. The overpotential required for CER with 0.05 Co-BV is lower than that of OER, which leads to selective CER at 1.1 V (vs. RHE). Co-doping into the BiVO4 lattice decreases the charge transfer resistance and enhances the CER kinetics due to its structural and electronic integration with the BV lattice. We demonstrate that Co-doping also improves the lifetime of the charge carrier and enhances the current density of CER and sustainability of the catalyst.

Sulfur Functionalization via Epoxide Ring Opening on a Reduced Graphene Oxide Surface to Form Metal (II) Organo-bis-[1,2]-oxathiin.

The epoxide ring-opening reaction in graphene oxide (GO) by nucleophiles is a very fascinating and advanced methodology to develop novel functional material. Herewith, we report an advanced strategy for opening the epoxide ring on the rGO surface via easily an available nucleophile (Na2S), which is further functionalized with O atom to obtain four-membered rings (FMRs). The Cd coordination with the S atom puts extra stress on the FMR leading to the C-C bond cleavage of the four-membered heteroatomic rings on the rGO surface. This strategic approach leads to the fabrication of an innovative metal (II) organo-bis-[1,2]-oxathiin (MOBOT) chemical moiety (M = Cd, Zn). The MOBOT compound further shows enhanced H2 generation activity and hence is promising as a potential photocatalyst for solar hydrogen generation. This compound might also be a potential candidate for optoelectronic applications.

Can Half-a-Monolayer of Pt Simulate Activity Like That of Bulk Pt? Solar Hydrogen Activity Demonstration with Quasi-artificial Leaf Device.

Pt is the best cocatalyst for hydrogen production. It is also well-known that the surface atomic layer is critical for catalysis. To minimize the Pt content as cocatalyst, herein we report on half-a-monolayer of Pt (0.5θPt) decorated on earth-abundant Ni-Cu cocatalyst, which is integrated with a quasi-artificial leaf (QuAL) device (TiO2/ZnS/CdS) and demonstrated for efficient solar hydrogen production. For the QuAL, TiO2 is sensitized with ZnS and CdS quantum dots by the SILAR method. The 0.5θPt-decorated Ni-Cu shows an onset potential of 0.05 V vs reversible hydrogen electrode for the hydrogen evolution reaction, which is almost similar to that of commercial Pt/C. Photoactivity of the present QuAL device with either bulk Pt or 0.5θPt-coated Ni-Cu cocatalyst is, surprisingly, equal. Our findings underscore that a fraction of a monolayer of Pt can enhance the activity of the cocatalyst, and it is worth exploring further for the high activity associated with atomic Pt and other noble metals.