Biochar from co-pyrolysis of biological sludge and woody waste followed by chemical and thermal activation: end-of-waste procedure for sludge management and biochar sorption efficiency for anionic and cationic dyes.

Nine biochars were produced by co-pyrolysis of sawdust and biological sludge following the "design of experiment" approach. Two kinds of sludge (both deriving from the treatment of mixed industrial-municipal wastewater) and two types of woody waste were selected as categorical predicting variables, while contact time, pyrolysis temperature, and sludge percentage were used as quantitative variables. Biochars were analysed for their product characteristics and environmental compatibility based on the European Standards (EN 12915-1:2009) for materials intended for water treatment (i.e. ash content, water leachable polycyclic aromatic hydrocarbons (PAHs) and elements), as well as for specific surface area (SSA), using them as response variables of a multivariate partial least square multiple regression, whose results provided interesting insights on the relationships between pyrolysis conditions and biochar characteristics. Biochars produced with sludge and/or providing the highest SSA values (258-370 m2 g-1) were selected to undergo a sustainable chemical treatment using a by-product of the gasification of woody biomass, complying in all cases with European Standards and achieving therefore the end-of-waste status for sewage sludge. The biochar deriving from the highest percentage of sludge (30% by weight) and with the highest SSA (390 m2 g-1) was thermally activated achieving SSA of 460 m2 g-1 and then tested for the sorption of direct yellow 50 and methylene blue in ultrapure water and real wastewater, compared to a commercial activated carbon (AC). The biochar showed Langmuir sorption maxima (Qm) 2-9 times lower than AC, thus highlighting promising sorption performances. Qm for methylene blue in wastewater (28 mg‧g-1) was confirmed by column breakthrough experiments.

Biochars intended for water filtration: A comparative study with activated carbons of their physicochemical properties and removal efficiency towards neutral and anionic organic pollutants.

Seven biochars (BCs) obtained from pyrolysis or gasification of different vegetal feedstocks were thoroughly characterized in comparison with three commercial activated carbons (ACs) routinely used in drinking water treatment plants. BCs and ACs characterization included the determinations of ash, iodine and methylene blue adsorption indexes, and the release of metals and polycyclic aromatic hydrocarbons, which were performed according to international standards applied for adsorption media to be used in drinking waters. Total specific surface area, micropore and mesopore specific surface area, pH of the point of zero charge, and the release of polychlorinated biphenyls were also determined in all chars. Principal component analysis and cluster analysis were performed in order to summarize the complex set of information deriving from the aforementioned characterizations, highlighting the BC most similar (BC6 from high temperature gasification of woody biomass) and most different (BC7 from low-temperature pyrolysis of corn cob) from ACs. These BCs were studied for their adsorption in ultrapure water towards diiodoacetic acid (an emergent disinfection by-product), benzene, and 1.2-dichlorobenzene, in comparison with ACs, and results obtained were fitted by linearized Freundlich equation. Overall, BC6 showed higher sorption performances compared to BC7, even though both BCs were less performing sorbents than ACs. However, the sorption properties of BCs were maintained also in real water samples collected from drinking water treatment plants.

Physicochemical properties and sorption capacities of sawdust-based biochars and commercial activated carbons towards ethoxylated alkylphenols and their phenolic metabolites in effluent wastewater from a textile district.

Three biochars were produced using sawdust from waste biomass, via a simple pyrolysis thermal conversion at 450, 650, and 850 °C (BC450, BC650, and BC850), without any activation process. These materials, together with vegetal and mineral commercial activated carbons (VAC and MAC), were characterized for their elemental composition, Brunauer-Emmett-Teller surface area, t-plot microporosity and Barrett-Joyner-Halenda mesoporosity. Moreover, iodine, phenol and methylene blue porosity indexes were measured. The materials were also evaluated for their pH of the point of zero charge, as well as near-surface chemical composition and surface functionality by means of X-ray photoelectron and Fourier-transform infrared spectroscopy. Ash content, water-extractable metals and polycyclic aromatic hydrocarbons (PAHs) were also determined. BC650 showed a much higher surface area (319 m2 g-1) compared to BC450 (102 m2 g-1), as well as an increase in aromatization and the residual presence of functional polar groups. BC850 exhibited a loss of polar and aromatic groups, with the dominance of graphitic carbon and the highest value of surface area (419 m2 g-1). Biochars comply with the EN 12915-1/2009 limits for metal and PAH release in water treatment. Biochars and MAC were tested using Langmuir and Freundlich isotherms for the sorption in real effluent wastewater of a mixture of 14 branched ethoxylated 4-t-octyl and 4-nonylphenols, as well as 4-t-octyl and 4-nonylphenol, the latter representing persistent, endocrine disrupting contaminants, widespread in the effluents from wastewater treatment plants and listed as priority/priority hazardous substances in the Directive 2013/39/EU. Biochars showed a lower sorption efficiency compared to MAC. The best performance was found for BC650 towards the alkylphenols (9-13 times less efficient than the MAC). Considering the lower market price of biochar compared to MAC (estimated as at least 16 times less expensive by a small market survey), the former can be considered more competitive than the latter.