Rapid Colorimetric Detection of Wound Infection with a Fluidic Paper Device.

Current procedures for the assessment of chronic wound infection are time-consuming and require complex instruments and trained personnel. The incidence of chronic wounds worldwide, and the associated economic burden, urge for simple and cheap point-of-care testing (PoCT) devices for fast on-site diagnosis to enable appropriate early treatment. The enzyme myeloperoxidase (MPO), whose activity in infected wounds is about ten times higher than in non-infected wounds, appears to be a suitable biomarker for wound infection diagnosis. Herein, we develop a single-component foldable paper-based device for the detection of MPO in wound fluids. The analyte detection is achieved in two steps: (i) selective immunocapture of MPO, and (ii) reaction of a specific dye with the captured MPO, yielding a purple color with increasing intensity as a function of the MPO activity in infected wounds in the range of 20-85 U/mL. Ex vivo experiments with wound fluids validated the analytic efficiency of the paper-based device, and the results strongly correlate with a spectrophotometric assay.

Array of individually addressable two-electrode electrochemical cells sharing a single counter/reference electrode for multiplexed enzyme activity measurements.

This work reports on the fabrication and performance of a new on-chip array of gold thin-film electrodes arranged into five individually addressable miniaturized electrochemical cells. Each cell shows a two-electrode configuration comprising a single working electrode and a counter/pseudo-reference electrode that is compartmentalized to be shared among all the cells of the array. Using this configuration, just six contact pads are required, which significantly reduces the chip overall surface area. Electrochemical characterization studies are carried out in solutions containing the two species of reversible redox pairs. The concentration of one redox species can reliably be measured at the working electrode by applying potentiostatic techniques to record the current due to the corresponding electrochemical reaction. The redox counterpart in turn undergoes an electrochemical process at the counter/pseudo-reference electrode, which, under optimized experimental conditions, injects current and keeps the applied potential in the electrochemical cell without limiting the current being recorded at the working electrode. Under these conditions, the electrode array shows an excellent performance in electrochemical detection studies without any chemical or electrical cross-talk between cells. The enzymatic activity of horseradish peroxidase, alkaline phosphatase and myeloperoxidase enzymes is analyzed using different redox mediators. Quasi-simultaneous measurements with the five electrochemical cells of the array are carried out within 1 s time frame. This array layout can be suitable for multiplexed electrochemical immunoassays and immunosensor approaches and implementation in simplified electrochemical ELISA platforms that make use of enzyme labels. Moreover, the array reduced dimensions facilitate the integration into compact fluidic devices.

A microfluidic device for the automated electrical readout of low-density glass-slide microarrays.

Microarrays are a powerful platform for rapid and multiplexed analysis in a wide range of research fields. Electrical readout systems have emerged as an alternative to conventional optical methods for microarray analysis thanks to its potential advantages like low-cost, low-power and easy miniaturization of the required instrumentation. In this work an automated electrical readout system for low-cost glass-slide microarrays is described. The system enables the simultaneous conductimetric detection of up to 36 biorecognition events by incorporating an array of interdigitated electrode transducers. A polydimethylsiloxane microfluidic structure has been designed that creates microwells over the transducers and incorporates the microfluidic channels required for filling and draining them with readout and cleaning solutions, thus making the readout process fully automated. Since the capture biomolecules are not immobilized on the transducer surface this readout system is reusable, in contrast to previously reported electrochemical microarrays. A low-density microarray based on a competitive enzymatic immunoassay for atrazine detection was used to test the performance of the readout system. The electrical assay shows a detection limit of 0.22±0.03 µg L(-1) similar to that obtained with fluorescent detection and allows the direct determination of the pesticide in polluted water samples. These results proved that an electrical readout system such as the one presented in this work is a reliable and cost-effective alternative to fluorescence scanners for the analysis of low-density microarrays.

Electrochemical nanocomposite-derived sensor for the analysis of chemical oxygen demand in urban wastewaters.

This work reports on the fabrication and comparative analytical assessment of electrochemical sensors applied to the rapid analysis of chemical oxygen demand (COD) in urban waste waters. These devices incorporate a carbon nanotube-polystyrene composite, containing different inorganic electrocatalysts, namely, Ni, NiCu alloy, CoO, and CuO/AgO nanoparticles. The sensor responses were initially evaluated using glucose as standard analyte and then by analyzing a set of real samples from urban wastewater treatment plants. The estimated COD values in the samples were compared with those provided by an accredited laboratory using the standard dichromate method. The sensor prepared with the CuO/AgO-based nanocomposite showed the best analytical performance. The recorded COD values of both the sensor and the standard method were overlapped, considering the 95% confidence intervals. In order to show the feasible application of this approach for the detection of COD online and in continuous mode, the CuO/AgO-based nanocomposite sensor was integrated in a compact flow system and applied to the detection of wastewater samples, showing again a good agreement with the values provided by the dichromate method.

Reusable conductimetric array of interdigitated microelectrodes for the readout of low-density microarrays.

Low-density protein microarrays are emerging tools in diagnostics whose deployment could be primarily limited by the cost of fluorescence detection schemes. This paper describes an electrical readout system of microarrays comprising an array of gold interdigitated microelectrodes and an array of polydimethylsiloxane microwells, which enabled multiplexed detection of up to thirty six biological events on the same substrate. Similarly to fluorescent readout counterparts, the microarray can be developed on disposable glass slide substrates. However, unlike them, the presented approach is compact and requires a simple and inexpensive instrumentation. The system makes use of urease labeled affinity reagents for developing the microarrays and is based on detection of conductivity changes taking place when ionic species are generated in solution due to the catalytic hydrolysis of urea. The use of a polydimethylsiloxane microwell array facilitates the positioning of the measurement solution on every spot of the microarray. Also, it ensures the liquid tightness and isolation from the surrounding ones during the microarray readout process, thereby avoiding evaporation and chemical cross-talk effects that were shown to affect the sensitivity and reliability of the system. The performance of the system is demonstrated by carrying out the readout of a microarray for boldenone anabolic androgenic steroid hormone. Analytical results are comparable to those obtained by fluorescent scanner detection approaches. The estimated detection limit is 4.0 ng mL(-1), this being below the threshold value set by the World Anti-Doping Agency and the European Community.

Fabrication of biofunctionalized microfluidic structures by low-temperature wax bonding.

In this work, a new fabrication technology for microfluidics based on the use of wax is described. Microfluidic structures are assembled using wax as both a thermoplastic adhesive layer between two glass substrates and a spacer layer defining the microchannels. Wax patterns with dimensions down to 25 µm are easily produced on glass substrates using specially developed decal-transfer microlithography. A complete microfluidic system is created by bonding the wax patterned layer with an additional glass substrate. On the basis of the special melting behavior of waxes, an effective glass-wax bonding is achieved at 40 °C by applying a soft pressure and without the requirement of any glass pretreatment. Wax bonding provides an effective sealing of the fluidic networks even on nonflat glass substrates (i.e., containing metal electrodes). The mild conditions required for the bonding process enables the fabrication of lab-on-a-chip devices incorporating biomolecules, as is demonstrated with the implementation of a simple heterogeneous immunoassay in a microfluidic device with amperometric detection.

ISFET based microsensors for environmental monitoring.

The use of microsensors for in-field monitoring of environmental parameters is gaining interest due to their advantages over conventional sensors. Among them microsensors based on semiconductor technology offer additional advantages such as small size, robustness, low output impedance and rapid response. Besides, the technology used allows integration of circuitry and multiple sensors in the same substrate and accordingly they can be implemented in compact probes for particular applications e.g., in situ monitoring and/or on-line measurements. In the field of microsensors for environmental applications, Ion Selective Field Effect Transistors (ISFETs) have a special interest. They are particularly helpful for measuring pH and other ions in small volumes and they can be integrated in compact flow cells for continuous measurements. In this paper the technologies used to fabricate ISFETs and a review of the role of ISFETs in the environmental field are presented.

Electronic integrated multisensor tongue applied to grape juice and wine analysis.

An integrated multisensor composed by six ISFET devices selective to common ions and heavy metals combined with a flow injection analysis (FIA) system has been applied as an electronic tongue to grape juice and wine sample analysis. The data obtained for several grape and wine variety samples analysis have been treated using multiparametric tools like principal component analysis (PCA) and soft independent modelling class analogy technique (SIMCA) for the patterning recognition and classification of samples and partial least squares (PLS) regression for quantification of several parameters of interest in wine production. The results obtained have demonstrated the potential of using those multisensors as electronic tongues not only for distinguishing the samples according to the grape variety and the vintage year but also for quantitative prediction of several sample parameters.

Monitoring of bentonite pore water with a probe based on solid-state microsensors.

Repositories for the disposal of radioactive waste generally rely on a multi-barrier system to isolate the waste from the biosphere. This multi-barrier system typically comprises the natural geological barrier provided by the repository host rock and its surroundings and an engineered barrier system (EBS). Bentonite is being studied as an appropriated porous material for an EBS to prevent or delay the release and transport of radionuclides towards biosphere. The study of pore water chemistry within bentonite barriers will permit to understand the transport phenomena of radionuclides and obtain a database of the bentonite-water interaction processes. In this work, the measurement of some chemical parameters in bentonite pore water using solid-state microsensors is proposed. Those sensors are well suited for this application since in situ measurements are feasible and they are robust enough for the long periods of time that monitoring is needed in an EBS. A probe containing an ISFET (ion sensitive field effect transistor) for measuring pH, and platinum microelectrodes for measuring conductivity and redox potential was developed, together with the required instrumentation, to study the chemical changes in a test cell with compacted bentonite. Response features of the sensors' probe and instrumentation performance in synthetic samples with compositions similar to those present in bentonite barriers are reported. Measurements of sensors stability in a test cell are also presented.