Enhancing Bond Strength of 3D-Printed Resin Posts Using Various Surface Pretreatments: An In Vitro Study.

PURPOSE: This study investigated the impact of common surface pretreatments on the contact angle (CA), surface free energy (SFE), and push-out bond strength (PBS) of custom 3D-printed resin posts. MATERIALS AND METHODS: Post spaces of 60 endodontically treated mandibular premolars were prepared. Custom 3D-printed posts made from permanent crown resin were fabricated for 50 randomly selected post spaces. The specimens were then divided into six groups (n = 10) based on their surface pretreatment methods. These methods included sandblasting (SB), silane (SL), hydrofluoric acid (HF), and hydrogen peroxide (HP). Additionally, two control groups were established: glass fiber control (GFC) and permanent resin control (PRC). CA and SFE were measured for each 3D-printed post group. PBS and failure mode analyses were conducted. The data were analyzed using the two-way ANOVA followed by the Tukey post hoc test (α = .05). RESULTS: The lowest CA values were found in the SB and SL groups. The SB group had the highest SFE compared to all other groups. SL markedly enhanced the PBS of the resin post compared to the PRC at the cervical, middle, and apical levels (P = .001, P = .000, and P = .002, respectively), and the values were comparable to those of the GFC (P = .695, P = .999, and P = .992, respectively). Except in the GFC, SB, and SL groups, mixed failure decreased from the cervical to apical levels, while adhesive failure rates increased. CONCLUSIONS: The application of silane and sandblasting to the surfaces of custom 3D-printed resin posts effectively increased their SFE, thereby enhancing their adhesion.

Monomer release, cell adhesion, and cell viability of indirect restorative materials manufactured with additive, subtractive, and conventional methods.

PURPOSE: The aim of this study was to measure residual monomer, cell adhesion, and cell viability of 3-dimensional printable permanent resin (PR), hybrid ceramic block (HCB), and indirect composite (IC) produced with additive, subtractive, and conventional techniques. METHODS: Five 8 × 8 × 2 mm3 samples of each material were prepared for each experiment. In a 24-h period, monomer release was analyzed with high-performance liquid chromatography, and cell viability and adhesion were evaluated with the water-soluble tetrazolium salt test. Data were analyzed with IBM SPSS Statistics 26.0 statistical software, and results were regarded as significant at α = 0.05. RESULTS: Monomer release (triethylene glycol dimethacrylate, urethane dimethacrylate, and Bisphenol A glycerolate dimethacrylate) was significantly higher in the IC group. Mean cell viability was significantly lower in the HCB group than in the IC group. CONCLUSION: All monomers in the tested materials were released at rates that were below clinical significance. Cell adhesion rates in the groups were similar. Cytotoxic response was classified as minor in the HCB and PR groups and non-cytotoxic in the IC group.

Comparative chemical properties, bioactivity, and cytotoxicity of resin-modified calcium silicate-based pulp capping materials on human dental pulp stem cells.

OBJECTIVES: This study investigated the cytotoxicity, the residual monomer release, degree of conversion (DC), calcium ion (Ca2+) release, and crystal structure of TheraCal PT (ThPT) by comparison with TheraCal LC (ThLC) and mineral trioxide aggregate (MTA). MATERIALS AND METHODS: The cytotoxicity of the cured materials was evaluated on human dental pulp stem cells (hDPSCs) isolated from third molars by the water-soluble tetrazolium salt (WST-1) method. The monomer release and DC of the resin-containing materials were analyzed by high-performance liquid chromatography (HPLC) and Fourier transform infrared (FTIR), respectively. The chemical composition and Ca2+ release of the materials were determined by scanning electronic microscopy-energy-dispersive spectroscopy (SEM-EDS), X-ray diffractometry (XRD), and inductively coupled plasma-optical emission spectroscopy (ICP-OES), respectively. Statistical differences were evaluated with one-way ANOVA, repeated measure ANOVA, and the Tukey test (p < 0.05). RESULTS: MTA showed significantly lower cytotoxicity than either ThLC or ThPT after 1, 3, and 7 days (p < 0.05). TEGDMA release of ThPT is significantly higher than ThLC (p < 0.05). All materials showed calcium Ca2+ release, with MTA significantly higher than the others (p < 0.05). CONCLUSIONS: MTA showed low cytotoxicity and high Ca2+ release compared to ThLC and ThPT. CLINICAL RELEVANCE: The cytotoxicity and residual monomer release of ThLC and ThPT may raise concerns about the viability of hDPSCs. Further investigations with the use of in vivo research models are required to validate in vitro bioactivity properties and the potential adverse biological effects of ThLC and ThPT on hDPSCs.

Do resin-based composite CAD/CAM blocks release monomers?

OBJECTIVE: The present study aimed to identify and quantify the elution of monomers of five different resin-based CAD/CAM blocks (RCBs) using HPLC. METHODS: Five different RCBs were used in the study: GC Cerasmart (CS), Voco Grandio blocs (GR), 3M Lava Ultimate (LU), Shofu Block (SB), and Vita Enamic (VE). Fifteen samples from each material were prepared using a low-speed precision diamond saw (ISOMET Buehler, Lake Bluff, IL, USA) at 5 × 5 × 4 mm size. After the preparation of samples, an extraction solution was mixed with %75/%25 ethanol/water. The samples were stored in the amber-colored bottles during three different immersed periods as 1 h, 24 h, and 90 days (n = 5). After immersion, 0.5 ml solutions were taken from each bottle and analyzed using HPLC. RESULTS: A total of 16.7 µg/ml of monomers from SB, 13.4 µg/ml of monomers from GR, 13.2 µg/ml of monomers from CS, and 6.7 µg/ml of monomers from LU were found after 3-m immersion. TEGDMA after 3-m of immersion was only released from the SB group, and also BisEMA was released from the CS group. Among the specimens immersed for 1 h, UDMA was released the least from the LU group and the most from the GR group (p < 0.05). Correspondingly, 24 h and 3 m after immersion, the highest release of monomers was found in the GR (p < 0.05). CONCLUSIONS: When the monomer release from RCBs was evaluated, it was shown that these materials released methacrylate-based monomers except VE, especially if they were kept in a solvent solution for a long time such as 3 m. CLINICAL SIGNIFICANCE: The novel resin-based CAD/CAM blocks might monomer release, which may cause cytotoxic effects. But, the detected amount of monomer release is below the estimated daily limit.