Effect of Drilling Preparation on Immediately Loaded Implants: An In Vivo Study in Sheep.

PURPOSE: To determine the biologic and biomechanical effects of two implant drilling protocols on the cortical bone around implants subjected to immediate loading. MATERIALS AND METHODS: A total of 48 implants were inserted into the mandibles of six sheep following one of two drilling protocols: undersized preparation (US; n = 24) and nonundersized preparation (NUS; n = 24). Immediately after implant insertion, an abutment was placed on each implant and 36 implants were subjected to 10 sessions of dynamic vertical loads (1,500 cycles, 1 Hz) of 25 N or 50 N. Insertion torque value (ITV) was recorded at implant installation. Resonance frequency analysis (RFA) was measured at implant insertion and at each loading session. Fluorochrome was administered at day 17, and the animals were euthanized after 5 weeks. The removal torque values (RTVs) were measured, and samples underwent histomorphometric, µCT (microcomputed tomography), and fluorescence image acquisition analyses. The bone volume density (BV/TV), bone-to-implant contact (BIC), bone area fraction occupancy (BAFO), and fluorochrome stained bone surface (MS) were calculated. A linear mixed model analysis was performed, and Pearson paired correlation was calculated. RESULTS: Five implants from the NUS group failed, with a mean ITV of 8.8 Ncm and an RFA value of 57. The mean ITVs for US group and NUS group were 80.5 (± 14) Ncm and 45.9 (± 25) Ncm, respectively (P < .001). No differences were noted in the RFA values from the time of implant insertion until the end of the study. No differences in RTV, BV/TV, BAFO, or MS were observed between the groups. Intense new bone formation took place in the NUS group implants that were subjected to load. CONCLUSIONS: Undersized preparation of cortical bone ensured a greater BIC compared to a nonundersized preparation. Moreover, this study demonstrated that immediate loading did not interfere with the osseointegration process, but loading induced intense new bone formation in the NUS group. It is not recommended to immediately load the implants when the clinically perceived primary stability is lower than an ITV of 10 Ncm and an RFA value of 60. Int J Oral Maxillofac Implants 2023;38:607-618. doi: 10.11607/jomi.9949.

Effect of antibiotic prophylaxis in dental implant surgery: A multicenter placebo-controlled double-blinded randomized clinical trial.

BACKGROUND: The growing resistance of bacteria to antimicrobial medicines is a global issue and a direct threat to human health. Despite this, antibiotic prophylaxis is often still routinely used in dental implant surgery to prevent bacterial infection and early implant failure, despite unclear benefits. There is a lack of sufficient evidence to formulate clear clinical guidelines and therefore there is a need for well-designed, large-scale randomized controlled trials to determine the effect of antibiotic prophylaxis. PURPOSE: To compare the effect of a presurgical antibiotic regimen with an identical placebo regimen in healthy or relatively healthy patients receiving dental implants. MATERIALS AND METHODS: The 474 patients participating in the study were recruited from seven clinics in southern Sweden. We randomized the patients into a test and a placebo group; the study was conducted double-blinded. Preoperatively, the test group received 2 g of amoxicillin and the control group, identical placebo tablets. The primary outcome was implant failure; secondary outcomes were postoperative infections and adverse events. Patients were evaluated at two follow-ups: at 7-14 days and at 3-6 months. RESULTS: Postoperative evaluations of the antibiotic (n = 238) and the placebo (n = 235) groups noted implant failures (antibiotic group: six patients, 2.5% and placebo group: seven patients, 3.0%) and postoperative infections (antibiotic group: two patients, 0.8% and placebo group: five patients, 2.1%). No patient reported any adverse events. Between-group differences in implant failures and postoperative infections were nonsignificant. CONCLUSION: Antibiotic prophylaxis in conjunction with implant placement is likely of small benefit and should thus be avoided in most cases, especially given the unabated growth in antibiotic-resistant bacteria. CLINICAL TRIAL REGISTRATION NUMBER: NCT03412305.

The use of implant-level connection in screw-retained fixed partial dentures: A 3-year randomised clinical trial.

OBJECTIVES: This randomised controlled trial compares the 3-year outcomes, that is, marginal bone-level (MBL) changes and clinical parameters, between an abutment-level (AL) and implant-level (IL) connection for implants with an internal conical connection (ICC) supporting a screw-retained fixed partial denture. MATERIAL AND METHODS: Fifty patients with 119 implants were randomly allocated to either the AL or IL group. Radiographic and clinical examinations were performed after one, two, and 3 years. A linear mixed model was used to evaluate the differences between groups. RESULTS: The MBL change was not significantly different between the groups at any point. The MBL was 0.12 ± 0.31 mm (AL) and 0.23 ± 0.26 mm (IL) after 1 year; 0.15 ± 0.34 mm (AL) and 0.17 ± 0.22 mm (IL) after 2 years; 0.18 ± 0.39 mm (AL) and 0.15 ± 0.21 mm (IL) after 3 years. The bleeding on probing was 43.44 ± 39.24% (AL) and 58.19 ± 41.20% (IL) after 1 year; 35.78 ± 39.22% (AL) and 50.43 ± 41.49% (IL) after 2 years; 51.27 ± 44.63% (AL) and 49.57 ± 37.31% (IL) after 3 years and was significantly different (p = .025) between 1 and 2 years. The probing depth showed a significant difference at each time point while the plaque was not significant between the groups. The overall technical, biological and prosthetic complication rates were 5.04%, 3.36%, and 16.00%, respectively. CONCLUSIONS: The MBL change was similar in the groups. The slight differences in the soft tissue complications between the groups are likely not of clinical relevance. An IL connection is considered to be a valid alternative to an AL set-up in ICC implants.

Estimation of Blood Loss in Oral and Maxillofacial Surgery by Measurements of Low Haemoglobin Levels in Mixtures of Blood, Saliva and Saline: a Laboratory Study.

OBJECTIVES: Estimating blood loss is an important factor in several surgical procedures. The accuracy of blood loss measurements in situations where blood is mixed with saliva and saline is however uncertain. The purpose of this laboratory study was to ascertain if blood loss measurements in mixtures of blood, saline, and saliva are reliable and could be applicable in a clinical setting. MATERIAL AND METHODS: Venous blood and resting saliva were collected from six volunteers. Saliva, saline, and combinations thereof were mixed with blood to obtain different concentrations. A portable spectrophotometer was first used to measure the haemoglobin concentration in undiluted venous blood followed by measurements of the haemoglobin concentration after each dilution. To examine the strength of linear relationships, linear regression and Pearson correlations were used. RESULTS: The measurements of haemoglobin concentrations in mixtures of blood, saline, and saliva were proven to be accurate for haemoglobin measurements > 0.3 g/dl (correlation = 0.986 to 1). For haemoglobin measurements < 0.3 g/dl, a small increase in haemoglobin values were reported, which was directly associated to the saliva concentration in the solution (correlation = 0.983 to 1). This interference of saliva was significantly eliminated by diluting the samples with saline, mimicking the clinical situation. CONCLUSIONS: The results suggest that a portable spectrophotometer can be used clinically to preoperatively measure the haemoglobin value of a venous blood sample and postoperatively measure the haemoglobin value of the collected liquids, including shed blood, thereby achieving a highly accurate method of measuring blood loss during oral and maxillofacial surgery.

Fixed full-arch maxillary prostheses supported by four versus six implants with a titanium CAD/CAM milled framework: 3-year multicentre RCT.

OBJECTIVES: This RCT compares marginal bone level (MBL) change and the clinical parameters after a 3-year function in maxillary implant-supported fixed complete dentures (FCDs) treated with four-implants (4-I) or six-implants (6-I). MATERIAL AND METHOD: Three centres treated 56 patients with 280 implants allocated to the 4-I or 6-I group. Radiographic and clinical examinations were performed. The primary outcome was to investigate MBL change between the groups. RESULTS: Implant survival rates were 100% and 99% in the 4-I and 6-I groups, respectively. Considering the clustering effects, the MBL change was not significantly different between the groups over the 3-year follow-up. The MBL in the 4-I group was 0.30 ± 0.50 mm at baseline, 0.24 ± 0.31 mm at 1 year and 0.24 ± 0.38 mm at 3 years. In the 6-I group, MBL was 0.14 ± 0.32 mm at baseline, 0.16 ± 0.35 mm at 1 year and 0.12 ± 0.26 mm at 3 years. There was a statistically significant difference between the groups at BL and 3Y. No significant differences between the groups were reported for clinical parameters at each time point as well as in between the visits. The technical and biological complications rates were 1.6% and 6.0%, respectively. Prosthetic complications affected 25 FCDs (47.2%). CONCLUSION: Marginal bone level change revealed a stable condition in the 3-year period in the two groups. Few technical and biological complications occurred apart from the chipping/fracture of the prosthetic teeth. Four-implant is a feasible solution if the rehabilitation is oriented towards the most cost-effective treatment and towards avoiding bone augmentation procedures. Clinicians have to consider the potential required visits for prosthetic maintenance.

Impact of a Hydrophilic Dental Implant Surface on Osseointegration: Biomechanical Results in Rabbit.

This study aimed to evaluate the effect of surface hydrophilicity on the biomechanical aspects of osseointegration of dental implants in the tibia and femur of rabbits. Forty-eight mature female New Zealand White rabbits were included, and 96 commercially pure, Grade 4, titanium dental implants (control group), and 96 implants of same macro geometry with the hydrophilic surface (test group) were used in this study. One osteotomy was performed in each tibia and femur on both sides of the rabbit, and four implants were placed in each rabbit. Control and test groups were randomly allocated on the left and right sides. During surgery, insertion torque (ITQ) value of the complete implant placement was recorded. After healing periods of 0, 2, 4, and 8 weeks after surgery, implant stability quotient (ISQ) value, and removal torque (RTQ) values were measured. No statistical difference was observed for ITQ, for ISQ and for RTQ between the control group and test group in tibia/femur for all time periods. The effect of hydrophilic properties on moderately roughened surfaces has no impact in terms of biomechanical outcomes (ISQ values and RTQ values) after a healing period of 2 to 8 weeks in rabbit tibias /femurs.

Craniofacial Height in Relation to Cross-Sectional Morphology of the Anterior Maxilla: An Anatomical Consideration in Implant Therapy.

PURPOSE: Patients who have a vertical growth pattern are more prone to complete alveolar bone growth later and run a higher risk for inhibition of growth and infraposition after implants have been placed. Moreover, it has been suggested for the same category of patients that craniofacial height may influence the alveolar bone morphology of the anterior maxilla during growth. Hence, it is important to identify such patients early when considering implant treatment in young patients. The purpose of this study was to investigate the height and width of the alveolar bone in the anterior maxilla in subjects with different craniofacial heights to assess if there is a relation between craniofacial height and the dimensions of the alveolar bone in the anterior part of the maxilla. MATERIALS AND METHODS: Measurements on cephalograms and cone beam computed tomography (CBCT) images of the maxilla from 180 fully dentate subjects were analyzed and categorized into three angle groups based on the craniofacial height: low-, normal-, and high-angle groups. Measurements of the alveolar bone were taken interradicular, at six reference points distributed between the first premolar regions in the maxilla. The height and width of the alveolar bone were measured with a standardized technique at 3, 6, 9, and 12 mm from the top of the alveolar process. RESULTS: Significant differences were found regarding the height of the alveolar bone in all the subgroups and regarding the width in the 9- and 12-mm subgroups, and between low-/normal- and low-/high-angle groups, where the high-angle group represented the thinnest alveolar bone. A significant difference was found between male and female patients concerning all dimensions of the alveolar bone. CONCLUSION: There is a relation between craniofacial height and the dimensions of the alveolar bone in the anterior part of the maxilla. Craniofacial height is an important factor to analyze when implant treatment is considered in the maxillary anterior region. This identification can preferably be carried out early in young patients who are still growing when various treatment options can still be considered.

In silico multi-scale analysis of remodeling peri-implant cortical bone: a comparison of two types of bone structures following an undersized and non-undersized technique.

PURPOSE: The aim of this multi-scale in silico study was to evaluate the influence of resorption cavities on the mechanical properties and load distribution in cortical bone after implant placement with two different drilling protocols. MATERIAL AND METHODS: Two different micro-scale bone structures were assessed: cortical bone models with cavities (test) and without cavities (control) were designed from µCT data. In a macro-scale model, representing a mandibular ridge, oblique load of 150 N was applied on the implant-abutment. Maximum principal stress/strain, and shear stress/strain were calculated in the macro- and micro-scale models. RESULTS: Test presented anisotropic material properties. In tests, significantly greater maximum values of Maximum principal stress/strain were calculated in micro-scale model. These values were located at the implant neck area in the macro-scale model and in the proximity of cavities in the micro-scale model respectively. Greater values of shear stress/strain were found in the test along the mandibular horizontal plane. CONCLUSIONS: Cortical bone with resorption cavities following undersized drilling showed an impaired load distribution compared with bone without cavities. Subsequently, stress/strain distribution suggests that this bone model is more prone to microdamage, thus delaying the healing process.

Intraosseous Temperature Change during Installation of Dental Implants with Two Different Surfaces and Different Drilling Protocols: An In Vivo Study in Sheep.

BACKGROUND: The intraosseous temperature during implant installation has never been evaluated in an in vivo controlled setup. The aims were to investigate the influence of a drilling protocol and implant surface on the intraosseous temperature during implant installation, to evaluate the influence of temperature increase on osseointegration and to calculate the heat distribution in cortical bone. METHODS: Forty Brånemark implants were installed into the metatarsal bone of Finnish Dorset crossbred sheep according to two different drilling protocols (undersized/non-undersized) and two surfaces (moderately rough/turned). The intraosseous temperature was recorded, and Finite Element Model (FEM) was generated to understand the thermal behavior. Non-decalcified histology was carried out after five weeks of healing. The following osseointegration parameters were calculated: Bone-to-implant contact (BIC), Bone Area Fraction Occupancy (BAFO), and Bone Area Fraction Occupancy up to 1.5 mm (BA1.5). A multiple regression model was used to identify the influencing variables on the histomorphometric parameters. RESULTS: The temperature was affected by the drilling protocol, while no influence was demonstrated by the implant surface. BIC was positively influenced by the undersized drilling protocol and rough surface, BAFO was negatively influenced by the temperature rise, and BA1.5 was negatively influenced by the undersized drilling protocol. FEM showed that the temperature at the implant interface might exceed the limit for bone necrosis. CONCLUSION: The intraosseous temperature is greatly increased by an undersized drilling protocol but not from the implant surface. The temperature increase negatively affects the bone healing in the proximity of the implant. The undersized drilling protocol for Brånemark implant systems increases the amount of bone at the interface, but it negatively impacts the bone far from the implant.

Effect of Misfit at Implant-Level Framework and Supporting Bone on Internal Connection Implants: Mechanical and Finite Element Analysis.

PURPOSE: To evaluate the effect of misfit at implant-level fixed partial dentures (ILFPDs) and marginal bone support on the generation of implant cracks. MATERIALS AND METHODS: This in vitro study included a mechanical fatigue test and finite element analysis. A mechanical cycling loading test was performed using 16 experimental models, each consisting of two parallel implants subdivided into four groups based on the misfit and the supporting bone condition. The framework, firmly seated at implants, was dynamically loaded vertically with a force of 1,600/160 N and 15 Hz for 1 × 106 cycles. Optical microscope, scanning electron microscope (SEM), and computed tomography three-dimensional (CT-3D) analyses were performed to detect impairments. Finite element models, representing the setups in the mechanical fatigue test, were used to represent the fatigue life. RESULTS: None of the mechanical components presented distortion or fracture at the macroscopic level during the test. In a microscopy evaluation, the fatigue test revealed scratches visible in the inner part of the conical portion of the implants regardless of the groups. SEM and CT-3D analysis revealed one implant from the misfit/no bone loss group with a microfracture in the inner part of the conical interface. The simulated effective stress levels in the coronal body were higher in the misfit groups compared with the no misfit groups. The misfit groups presented effective stress levels, above 375 MPa, that penetrated the entire wall thickness. The no bone loss group presented an effective stress level above 375 MPa along its axial direction. In the no misfit group, the area presenting effective stress levels above 375 MPa in the conical connection was larger for the bone loss group compared with the no bone loss group. CONCLUSION: This study confirmed that implant fracture is an unlikely adverse event. A clear pattern of effective distribution greater than fatigue limit stresses could be noticed when the misfit was present. The dynamic load simulation demonstrated that the crack is more likely to occur when implants are fully supported by marginal bone compared with a bone loss scenario. Within the limitations of this study, it is speculated that marginal bone loss might follow the appearance of an undetected crack. Further research is needed to develop safe clinical protocols with regard to ILFPD.

Implant vs abutment level connection in implant supported screw-retained fixed partial dentures with cobalt-chrome framework: 1-year interim results of a randomized clinical study.

BACKGROUND: Screw-retained fixed partial dentures (FPD) have shown a lower incidence of biologic complications and an easier retrievability compared with cemented FPD. PURPOSE: To compare the marginal bone loss at conical connection implant restored with a screw retained cobalt-chrome FPD in an implant-level (IL) or an abutment-level (AL) setup. MATERIALS AND METHODS: Patients with at least two adjacent missing teeth were randomly allocated to be restored with IL or AL FPD. Periapical radiographs and clinical examination were taken at implant placement, prosthetic connection, 6 and 12 months to evaluate marginal bone loss (MBL), and soft tissue conditions. Complications were used to calculate prognostic indexes. RESULTS: Fifty patients were treated with 50 FPD supported by 119 implants. The difference of MBL between the IL and AL groups was statistically significant (P = 0.003). At 1 year, MBL was 0.086 ± 0.313 mm and 0.005 ± 0.222 mm in the IL and AL groups, respectively. The presence of BoP increased with time in IL, whereas it decreased in AL group (P < 0.001). A minor complication was encounted in one FPD. CONCLUSIONS: A low grade of MBL was present after 1 year. IL showed greater amount of MBL and soft tissue inflammation indexes than AL. In FPD, AL may be a safer procedure than IL setup in order to preserve a healthy periimplant tissue.

Volumetric measurement of dentoalveolar defects by means of intraoral 3D scanner and gravimetric model.

The aim of this study was to evaluate the accuracy in volumetric measurements obtained on an experimental model using an intraoral scanner and a gravimetric method. Three identical partial dentate maxillary acrylic models with three fabricated alveolar defects, in anterior and posterior regions, were scanned using an intraoral scanner (20 scans/defects). The defects differed in terms of size and distance of neighbouring teeth. As references, replicas of each defect were created using a dimensional stable silicone impression material. After measuring the mass of each replica, the volume was calculated by dividing the mass of each replica by the density of the impression material. The defects had a volume, according to the gravimetric method, ranging from 40.5 to 143.7 mm3. The scans were imported to metrology software for analyses. Accuracy was determined in terms of trueness and precision. The mean trueness for all defect types was 0.168 mm3 (SD 0.691, range 2.82). There was no statistical significant difference between the mean trueness for all defects measured (p = 0.910). The mean precision for all defect types was 0.147 mm3 (SD 0.524, range 2.86). There were no statistical significant differences between the dental models in regard to mean precision (p = 0.401), however, there were statistical significant differences between defects in position 1 and 2 (p = 0.002) and 1 and 3 (p = 0.001). Based on the findings of this study, the intraoral scanner utilized in the current study presented an acceptable level of accuracy when measuring volume of defects.

Vertical Bone Augmentation Using Ring Technique with Three Different Materials in the Sheep Mandible Bone.

PURPOSE: The purpose of this study was to examine the volumetric alterations and osseointegration properties in the augmented area of the ring technique using different types of bone graft material in sheep mandible bone. MATERIALS AND METHODS: Three different materials (columnar forms, 7-mm diameter, 3-mm height) were stabilized using dental implants with a turned surface in the mandible bone of Finnish Dorset cross-bred sheep: group A, autogenous bone; group B, bovine bone; group C, biphasic bone substitute. Animals were euthanized after 5 weeks (N = 6). Three-dimensional image data by digital oral scanner were taken at the surgery and sacrifice, and the volume alteration of the material was calculated. The bone samples were fixed in formalin and dehydrated in ethanol. Resin-embedded samples were subjected to non-decalcified ground sectioning, and histologic and histomorphometric analysis (bone and material area alteration, bone-to-implant contact [BIC]) were done. RESULTS: In three-dimensional (3D) image analysis, group A showed a statistically higher percentage of remaining materials compared with groups B and C. The histologic observation showed no new bone formations around the implants in all groups, especially at the maxillary site of the implant in the augmented area. In histomorphometric analysis, group A showed a statistically higher percentage of bone area (BA) compared with groups B and C; however, in all groups, bone-to-implant contact (BIC) showed low values, and there were no statistical differences between groups. CONCLUSION: The results of this study suggested that the autogenous bone maintained bone volume around the dental implant using the ring technique, and the impact of surface properties was of some importance; osseointegration with the turned surface in the augmented area showed low BIC values in all groups.

Treatment outcomes and patient-reported quality of life after orthognathic surgery with computer-assisted 2- or 3-dimensional planning: A randomized double-blind active-controlled clinical trial.

INTRODUCTION: Thorough treatment planning is essential for a good clinical outcome in orthognathic treatment. The planning is often digital. Both 2-dimensional (2D) and 3-dimensional (3D) software options are available. The aim of this randomized 2-arm parallel double-blinded active-controlled clinical trial was to compare the outcomes of computer-based 2D and 3D planning techniques according to patient-reported health related quality of life. The hypothesis was that a 3D technique would give a better treatment outcome compared with a 2D technique. METHODS: Orthognathic treatment for 62 subjects, aged 18 to 28 years, with severe Class III malocclusion was planned with both 2D and 3D techniques. After treatment planning but before surgery, the patients were randomly allocated via blind collection of 1 enveloped card for each subject in a 1:1 ratio to the test (3D) or the control (2D) group. Thus, the intervention was according to which planning technique was used. The primary outcome was patient-reported outcome measures. The secondary outcome was relationship between patient-reported outcome measures and cephalometric accuracy. Questionnaires on the patient's health-related quality of life (HRQoL) were distributed preoperatively and 12 months after surgical treatment. The questionnaires were coded, meaning blinding throughout the analysis. Differences between groups were tested with the Fisher permutation test. The HRQoL was also compared with measurements of cephalometric accuracy for the 2 groups. RESULTS: Three subjects were lost to clinical follow-up, leaving 57 included. Of these, 55 subjects completed the questionnaires, 28 in the 2D and 27 in the 3D groups. No statistically significant difference regarding HRQoL was found between the studied planning techniques: the Oral Health Impact Profile total showed -3.69 (95% confidence interval, -19.68 to 12.30). Consistent results on HRQoL and cephalometric accuracy showed a difference between pretreatment and posttreatment that increased in both groups but to a higher level in the 3D group. A difference between pretreatment and posttreatment HRQoL was shown for both groups, indicating increased quality of life after treatment. This supports recent findings comparing 3D and 2D planning techniques. No serious harm was observed during the study. CONCLUSIONS: Improvements of HRQoL were shown after treatment independent of which planning technique, 2D or 3D, was used. No statistically significant difference was found between the planning techniques. REGISTRATION: This trial was not registered. PROTOCOL: The protocol was not published before trial commencement. FUNDING: This project was supported by personal grants to Martin Bengtsson from the Scandinavian Association of Oral and Maxillofacial Surgeons (25000 SEK), the Southern Region of the Swedish Dental Association (50000 SEK), and the Swedish Association of Oral and Maxillofacial Surgeons (25000 SEK). The sponsors had no influence on the study design, analysis of the data, or the writing of the article.

Influence of different drilling preparation on cortical bone: A biomechanical, histological, and micro-CT study on sheep.

OBJECTIVE: The aim of this study was to investigate the extent of cortical bone remodeling between two different drilling protocols by means of histomorphometric, µ-CT, and biomechanical analyses. MATERIAL AND METHODS: A total of 48 implants were inserted into the mandible of six sheep following two drilling protocols: Group A (Test, n = 24), undersized preparation; Group B (Control, n = 24), non-undersized preparation. The animals were euthanatized to obtain 5 and 10 weeks of implantation time. Removal torque (RTQ) was measured on 12 implants of each group and the peri-implant bone was µ-CT scanned. Bone volume density (BV/TV) was calculated in pre-determined cylindrical volumes, up to 1.5 mm from implant surface. Non-decalcified histology was prepared on the remaining 12 implants from each group, where total bone-to-implant contact (totBIC) and newly-formed BIC (newBIC) was measured. Bone Area Fraction Occupancy (BAFO) was determined in pre-determined areas up to 1.5 mm from implant surface. Paired sample t test or Wilcoxon signed-rank test was used to investigate differences between the groups. RESULTS: Group A presented significantly increased RTQ value at 5 weeks, while no difference was observed at 10 weeks. Group B presented increased BV/TV value at 5 weeks. Both groups showed comparable values for totBIC at both time-points. However, Group A presented significantly lower newBIC at 5 weeks. Higher BAFO was observed in Group B at 5 weeks. CONCLUSIONS: Implants inserted into undersized sites has an increased biomechanical performance, but provoked major remodeling of the cortical bone during the early healing period compared to non-undersized preparations. After 10 weeks, no difference was observed.

Craniofacial height in relation to cross-sectional maxillary and mandibular morphology.

BACKGROUND: In order to gain a better understanding of how growth of the alveolar bone is linked to the vertical development of the face, the purpose of this study was to investigate if there is an association between the cross-sectional morphology of the maxillary and mandibular bodies with the craniofacial height, using images from cone beam computed tomography (CBCT). METHODS: From 450 pre-treatment CBCT scans, 180 were selected to be included in the study. Lateral head images were generated from the CBCT scans and were used to categorise subjects into three groups based on their vertical craniofacial height. Cross-sectional images from CBCT volumes were reformatted of the maxillary and mandibular bodies at five locations in the maxilla and five in the mandible. Each image was measured at one height and two width measurements. Statistical analysis performed was the one-way analysis of variance with a Tukey post hoc test. A significance level of 5% was used in all comparisons. RESULTS: Patients with large vertical craniofacial height had a significantly higher cross-sectional area both in the maxilla and in the mandible. In the same group, the cross-sectional area was significantly thinner in the mandible compared with the other two groups, especially in the anterior region. CONCLUSIONS: This study further highlights the close relationship between craniofacial height and alveolar bone dimensions and contributes with important knowledge for planning and follow-up of comprehensive dental- and orthodontic treatments.

Effects of Bacterial Contamination on Dental Implants During Surgery: A Systematic Review.

INTRODUCTION: Contamination during surgery negatively influences the prognosis of orthopaedic implants; however, it has not been proven whether contamination influences the success of dental implant treatment. The aim of the systematic review was to investigate if there exists evidence in the literature whether contamination of dental implants during surgery affects osseointegration and clinical success. MATERIALS AND METHODS: Four data bases were used for the literature search. Primary studies and reviews regarding both clinical and preclinical research were eligible. Rating of the summarized quality of the evidence was performed. RESULTS: Five preclinical studies were included. Because of the estimated high risk of bias in all included studies and extensive differences in study design between the included studies, meta-analysis was not performed and no reliable aggregated data could be extracted. CONCLUSIONS: It is suggested that the scientific evidence with regard to the current topic is insufficient. Further controlled studies are warranted.

Bacterial diversity in medication-related osteonecrosis of the jaw.

OBJECTIVE: The aim was to study the association between microflora and medication-related osteonecrosis of the jaw (MRONJ) by using culture-independent molecular techniques to detect bacteria in necrotic bone lesions. STUDY DESIGN: Included were 18 consecutive patients with MRONJ, 10 with osteoporosis and 8 cancer patients. Bone biopsies were retrieved from the center of the necrotic bone and from visually healthy bone, and 16 S rRNA gene fragments from bacterial DNA were amplified with polymerase chain reaction. RESULTS: The study revealed a diversity of bacteria represented by 16 S rRNA sequences in all the necrotic bone samples and in 60% of the visually healthy bone. Eight dominating taxa groups were identified at the genus level: Porphyromonas, Lactobacillus, Tannerella, Prevotella, Actinomyces, Treponema, Streptococcus, and Fusobacterium. CONCLUSIONS: The necrotic bone lesions contained mainly anaerobic bacteria, representative of periodontal microflora, suggesting that a periodontal infection in combination with antiresorptive treatment could initiate osteonecrosis.

Biomechanical, Biologic, and Clinical Outcomes of Undersized Implant Surgical Preparation: A Systematic Review.

PURPOSE: To compile the current evidence on biomechanical, biologic, and clinical outcomes of undersized surgical preparation protocols in dental implant surgery. MATERIALS AND METHODS: An electronic search using three different databases (PubMed, Web of Science, and Cochrane Library) and a manual hand search were performed including in vitro, animal, and clinical studies published prior to October 2015. Studies in which an undersized drilling protocol was compared with a nonundersized drilling protocol were included. RESULTS: From an initial selection of 1,655 titles, 29 studies met the inclusion criteria, including 14 biomechanical, 7 biologic, 6 biologic and biomechanical, and 2 clinical. Due to methodologic variation, meta-analysis was not performed. Several studies showed that implants inserted with an undersized drilling approach reached a significantly higher insertion torque value than conventional drilling in low-density substrates, while this effect is less evident if a thick cortical layer is present. Similar results in terms of boneto-implant contact (BIC) were achieved in the longer term between implants inserted with undersized and nonundersized protocols. Results in the short term were inconclusive. Clinical studies did not show negative outcomes for undersized drilling, although clinical evidence was sparse. No data are available on marginal bone loss. CONCLUSION: From the biomechanical standpoint, an undersized drilling protocol is effective in increasing insertion torque in low-density bone. Biologic response in long-term healing after undersized implant placement is comparable to that in the nonundersized surgical drilling protocol. Clinical studies indicate that performing an undersized drilling protocol on low-density bone is a safe procedure; however, more extensive studies are needed to confirm these data.

Osteonecrosis of the jaw in patients treated with oral and intravenous bisphosphonates: experience in Sweden.

OBJECTIVE: To describe the prevalence, inciting factors, and treatment outcomes of bisphosphonate-related osteonecrosis of the jaw (BRONJ) during the 2003-2010 period in southern Sweden (population, approximately 1.2 million people). STUDY DESIGN: Patient records were searched for inflammatory conditions including unspecified inflammation, osteomyelitis, osteonecrosis due to drugs, and other osteonecrosis. Data on underlying disease, type of bisphosphonate (BP), inciting factor, location, stage, treatment, and treatment outcomes were collected. RESULTS: Of the 341 patients identified, 55 had been diagnosed with BRONJ. Those with a malignant disease were treated with intravenous BPs, and those with osteoporosis were treated with oral BPs. All but 5 were treated with antibiotics and 47 with local resection. Healing was recorded in 79% of patients with osteoporosis and in 26% of patients with malignant disease. CONCLUSIONS: Healing in patients with osteoporosis occurred more frequently than in patients with a malignant disease treated with intravenous BPs (P = .00009).