Multifunctional Core-Shell NiFe2O4 Shield with TiO2/rGO Nanostructures for Biomedical and Environmental Applications.

Multifunctional core@shell nanoparticles have been synthesized in this paper through 3 stages: NiFe2O4 nanoparticles by microwave irradiation using Pedalium murex leaf extract as a fuel, core@shell NiFe2O4@TiO2 nanoparticles by sol-gel, and NiFe2O4@TiO2@rGO by sol-gel using preprepared reduced graphene oxide obtained by modified Hummer's method. XRD analysis confirmed the presence of both cubic NiFe2O4 spinel and tetragonal TiO2 rutile phases, while Raman spectroscopy analysis displays both D and G bands (I D /I G = 1.04) associated with rGO. Morphological observations by HRTEM reveal a core-shell nanostructure formed by NiFe2O4 core as confirmed by SAED with subsequent thin layers of TiO2 and rGO. Magnetic measurements show a ferromagnetic behavior, where the saturation magnetization drops drastically from 45 emu/g for NiFe2O4 to 15 emu/g after TiO2 and rGO nonmagnetic bilayers coating. The as-fabricated multifunctional core@shell nanostructures demonstrate tunable self-heating characteristics: rise of temperature and specific absorption rate in the range of ΔT = 3-10°C and SAR = 3-58 W/g, respectively. This effectiveness is much close to the threshold temperature of hyperthermia (45°C), and the zones of inhibition show the better effective antibacterial activity of NTG against various Gram-positive and Gram-negative bacterial strains besides simultaneous good efficient, stable, and removable sonophotocatalyst toward the TC degradation.

Bitmap and vectorial hologram recording by using femtosecond laser pulses.

In this paper, we present two approaches for recording a quasi-hologram on the steel surface by femtosecond laser pulses. The recording process is done by rotating the polarization of the laser beam by a half-wave plate or a spatial light modulator (SLM), so we can control the spatial orientation of the formed laser-induced periodic surface structures (LIPSS). Two different approaches are shown, which use vector and bitmap images to record the hologram. For the first time to our knowledge, we managed to record a hologram of a bitmap image by continuously adjusting the laser beam polarization by SLM during scanning. The developed method can substantially improve hologram recording technology by eliminating complex processing procedures, which can lead to increasing the fabrication speed and reducing the cost.

On the phase-space catastrophes in dynamics of the quantum particle in an optical lattice potential.

We have investigated the dynamics of a quantum particle in the optical lattice potential. Initially, the quantum particle was represented by a Gaussian wave packet, located in the center of the well. The corresponding Schrödinger equation was solved explicitly by the method of the Chebyshev global propagation. Obtained solutions were also used for the construction of the Wigner functions. We found a great number of local abrupt changes of the solution shape. To explain this behavior, we used the fact that structurally stable systems, which form the largest class of the low dimensional dynamical systems, can be modeled and classified according to the catastrophe theory. All important features of the exact solution were explained on the basis of the mathematical properties of the catastrophic model. Such an approach enabled us to extract relevant information out of numerical solutions without employing any kind of approximations. We have investigated the influence of the Wigner catastrophes on the details of the quantum-classical correspondence breakdown. The wave packet was found to expand rapidly, filling the whole classically available area of the phase space. It was found that its self-interference pattern saturates quickly. A region of the phase space emerges in which the Wigner function oscillations transform into the singularity driven fluctuations. Once this region covers the whole area of the phase space, a wave packet dynamics enters into the new regime where its Wigner function fluctuates around the ergodic average. It will be shown that all mentioned processes are caused by the proliferation of the catastrophes and their mutual interactions.

Coordinated self-interference of wave packets: a new route towards classicality for structurally stable systems.

This is a study of proton transmission through planar channels of tungsten, where a proton beam is treated as an ensemble of noninteracting wave packets. For this system, the structural stability manifests in an appearance of caustic lines, and as an equivalence of self-interference produced waveforms with canonical diffraction patterns. We will show that coordination between particle self-interference is an additional manifestation of the structural stability existing only in ensembles. The main focus of the analysis was on the ability of the coordination to produce classical structures. We have found that the structures produced by the self-interference are organized in a very different manner. The coordination can enhance or suppress the quantum aspects of the dynamics. This behavior is explained by distributions of inflection, undulation, and singular points of the ensemble phase function, and their bifurcations. We have shown that the coordination has a topological origin which allows classical and quantum levels of reality to exist simultaneously. The classical behavior of the ensemble emerges out of the quantum dynamics without a need for reduction of the quantum to the classical laws of motion.

A monitorable and renewable pollution filter based on graphene nanoplatelets.

This paper deals with the fabrication, modeling and experimental characterization of a monitorable and renewable graphene-based pollution filter. The main goal is to demonstrate a method to monitor the status of such a filter in real time during its operating phases: pollutant adsorption, saturation, and regeneration. The filter is realized by a disk of pressed graphene nanoplatelets. This is a low-cost type of graphene which has recently drawn great interest due to its potential use in large scale industrial production. Here the nanomaterial is obtained through the exfoliation method assisted by microwave irradiation, by exploiting the thermal expansion of commercial intercalated graphite, according to a low-cost and ecologically friendly procedure. The filter is used here to adsorb acetonitrile, a toxic water-soluble organic compound that is present in some industrial solvents and paints. The monitoring method is based on the interpretation of the time variation of the electrical impedance measured during filter operation. There are two main results of the paper: Firstly, the graphene filter is shown to be effective in adsorbing the above pollutant, with the additional feature of being fully renewable: all the pollutant can be removed from the filter without the need of costly physical or chemical processes. Secondly, monitoring of the time-evolution of the electrical impedance allows efficient detection of the different phases of the filter life cycle: clean, polluted, saturated and regenerated. This feature is of potential interest since it enables the predictive maintenance of such filters.

Occurrence and antimicrobial susceptibility of Campylobacter spp. on fresh and refrigerated chicken meat products in Central Italy.

This study investigated the presence and the level of Campylobacter spp. contamination in 41 thigh samples (with skin) and 37 skinless breast samples collected at the end of slaughter (T1) and after 10 day period at refrigeration temperature (4°C) (T2), corresponding to their commercial shelf life. The isolates were phenotypically classified as Campylobacter spp. and successively identified by conventional multiplex PCR. The antimicrobial susceptibility of the isolates from fresh thigh and breast samples was also determined via the microdilution method (MIC) in Eucamp microtitre plates with known scalar concentrations of: gentamicin (GEN), streptomycin (ST), ciprofloxacin (CIP), tetracycline (TET), erythromycin (ERY), and nalidixic acid (NA). A greater percentage of positivity for Campylobacter spp. (P < 0.001) was observed in thighs and C.jejuni appeared to be the most common species identified at this level (P < 0.001) followed from its association with C.coli. There was a global reduction of Campylobacter spp. in both thigh and breast samples at T2 (P < 0.001) showing that the refrigeration was able to reduce Campylobacter count. The prevalence of resistance to CIP, TET, NA, and ERY was evidenced for C.jejuni and C. coli. The co (TET-NA, CIP-NA) and multiple resistant (CIP-TET-NA, CIP-TET- NA-ERY) isolates came from the thigh products. It should be highlighted the presence of Campylobacter spp. isolates resistant to ST occurred in breast samples, responsible for the ST-CIP co-resistance and ST-CIP-TE multi-resistance profiles, higher in breast than in thigh products (P > 0.001). The presence of Campylobacter isolates resistant to ST can be further investigated since it is used for therapeutic treatment of several bacterial diseases in humans.

Genetic diversity and antimicrobial resistance profiles of Campylobacter coli and Campylobacter jejuni isolated from broiler chicken in farms and at time of slaughter in central Italy.

AIMS: Genetic diversity and antimicrobial resistance of Campylobacter coli and Campylobacter jejuni were investigated along the broiler chicken production chain in central Italy. METHODS AND RESULTS: Campylobacter sp. isolated from cloacal swabs in farms (n = 116) and from the neck skin of chilled and eviscerated carcasses at slaughter (n = 24) were identified as C. coli (n = 99) and C. jejuni (n = 41) by multiplex PCR. Characterization by single amplified fragment length polymorphism (s-AFLP) revealed a specific genotype of Campylobacter for each farm. Minimal inhibitory concentration showed high prevalence of fluoroquinolones (70%), tetracycline (70%) and erythromycin (30%) resistance among C. coli isolates. Campylobacter jejuni isolates showed lower prevalence of fluoroquinolone (39%) and tetracycline (10%) resistance, and all isolates were susceptible to erythromycin. The S-AFLP types of the C. coli and C. jejuni isolates were associated with their antimicrobial resistance profiles (P < 0·001). CONCLUSIONS: The genetic diversity detected in Campylobacter isolates suggested that a specific genotype was harboured in each farm. A considerable number of C. coli isolates were resistant to erythromycin. SIGNIFICANCE AND IMPACT OF THE STUDY: Campylobacter coli was detected more frequently than C. jejuni in contrast to common findings for poultry. The high prevalence of 30% resistance to erythromycin in C. coli strains isolated from poultry is worrisome, as this is the first antibiotic of choice to treat human campylobacteriosis.

Bottom-up realization and electrical characterization of a graphene-based device.

We propose a bottom-up procedure to fabricate an easy-to-engineer graphene-based device, consisting of a microstrip-like circuit where few-layer graphene nanoplatelets are used to contact two copper electrodes. The graphene nanoplatelets are obtained by the microwave irradiation of intercalated graphite, i.e., an environmentally friendly, fast and low-cost procedure. The contact is created by a bottom-up process, driven by the application of a DC electrical field in the gap between the electrodes, yielding the formation of a graphene carpet. The electrical resistance of the device has been measured as a function of the gap length and device temperature. The possible use of this device as a gas sensor is demonstrated by measuring the sensitivity of its electrical resistance to the presence of gas. The measured results demonstrate a good degree of reproducibility in the fabrication process, and the competitive performance of devices, thus making the proposed technique potentially attractive for industrial applications.

Collapse and hybridization of RNA: view from replica technique approach.

The replica technique method is applied to investigate the kinetic behavior of the coarse-grained model for the RNA molecule. A non-equilibrium phase transition of second order between the glassy phase and the ensemble of freely fluctuating structures has been observed. The non-equilibrium steady state is investigated as well and the thermodynamic characteristics of the system have been evaluated. The non-equilibrium behavior of the specific heat is discussed. Based on our analysis, we point out the state in the kinetic pathway in which the RNA molecule is most prone to hybridization.

Sharp variations in the electronic properties of graphene deposited on the h-BN layer.

Investigation of the complex structure based on the graphene monolayer and the twisted BN monolayer was carried out. Sharp variations in the electronic structure during the hydrogen adsorption at low concentration were observed. Upon increasing the hydrogen concentration on the structure surfaces more impurity levels were observed due to the addition of the hydrogen atoms without any dependence on the position of hydrogen atoms on graphene and BN surfaces. An investigation of the dependence of the band gap on the hydrogen concentration on the Moiré surface was made. Upon increasing the hydrogen concentration the value of the band gap increased up to 0.5 eV.

Epoxy resin/carbon black composites below the percolation threshold.

A set of epoxy resin composites filled with 0.25-2.0 wt.% of commercially available ENSACO carbon black (CB) of high and low surface area (CBH and CBL respectively) has been produced. The results of broadband dielectric spectroscopy of manufactured CB/epoxy below the percolation threshold in broad temperature (200 K to 450 K) and frequency (20 Hz to 1 MHz) ranges are reported. The dielectric properties of composites below the percolation threshold are mostly determined by alpha relaxation in pure polymer matrix. The glass transition temperature for CB/epoxy decreases in comparison with neat epoxy resin due to the extra free volume at the polymer-filler interface. At room temperature, the dielectric permittivity is higher for epoxy loaded with CBH additives. In contrast, at high temperature, the electrical conductivity was found to be higher for composites with CBL embedded. The established influence of the CB surface area on the broadband dielectric characteristics can be exploited for the production of effective low-cost antistatic paints and coatings working at different temperatures.

The electrical properties of epoxy resin composites filled with Cnts and carbon black.

This work introduces an experimental activity related to the realization of an epossidic nanostructured material that develops the function of covering for electronic circuits in aeronautical field. This covering meets the demand of protection of these circuits from possible troubles of electromagnetic nature. In order to realize this covering we used an epoxy resin as matrix (Epon 828) loaded with conductive nanofillers or carbon nanotubes (Cnts). To check the efficiency of the coating we have considered the carbon black, filler widely used as a conductive covering for screenings. We have considered different percentages of the different fillers, precisely 0.1%, 0.25% and 0.5% wt (% valued in comparison to the weight of the resin). From every mixture 12 samples have been obtained (the size of every sample is 10 mm x 10 mm x 10 mm). Every sample has been subjected to electrical measurements, that have concerned the measurement of current intensity and resistance (so as to allow the evaluation of the enhancement of the conductivity), through the application of different values of voltage. The results have demonstrated that the epoxy matrix loaded with Cnts yields higher values of electrical conductivity than the same matrix loaded with carbon black.

Multiwalled carbon nanotube buckypaper: toxicology and biological effects in vitro and in vivo.

AIM: We evaluated the effect of buckypaper (BP) on cancer and primary cell lines in vitro and in vivo in laboratory rats. BP is an innovative material with interesting physical/chemical properties that has possible pharmacological and prosthetic employment. Given that precautions need to be taken where carbon nanotubes are injected into human body for drug delivery, as contrast agent-carrying entities for MRI or as the material of a new prosthesis generation, we assessed the toxicity of BP carbon nanotubes. BP has structural resemblance to asbestos, whose toxicity has been linked to cancer. RESULTS: BP decreased proliferation of human colorectal, breast and leukemic cancer cell lines in vitro. However, BP had no effect on the proliferation and viability of normal human arterial smooth muscle cells and human dermal fibroblasts in vitro. in vivo, BP induced a moderate inflammatory reaction but had no mutagenic effects. After BP implantation the animals showed an inflammatory reaction followed 2 weeks later by a cicatrization reaction with the organization and fibrosis of the scar. CONCLUSION: These results show a low toxicity of BP both in vitro and in vivo.

Nanomaterials and lung toxicity: interactions with airways cells and relevance for occupational health risk assessment.

Engineered nanoparticles (NP) comprise various classes of technological materials with innovative properties. Although inhalation is less likely for engineered nanomaterials (NM) compared with ambient or mineral dust particles, this can happen during bulk manufacture and handling of freely dispersible NP. In this mini-review we summarize recent data on NP and CNT (carbon nanotubes) hazards, with particular emphasis on toxic effect on lung and in cell culture of lung origin. Owing to the highest deposition efficiency in the alveolar area, primary interactions of NM occur with epithelial and alveolar macrophages (AM). Scarce data are available to date on the cell mechanisms underlying NM permeability across the airway epithelium, but the absorption of NP through airways does not seem to require epithelial mediation, suggesting rather the involvement of alternative mechanisms such as AM-dependent dissemination. The relationship between toxicity and particle characteristics may be complex, involving size, surface area and surface chemistry. Some NM act according to an oxidative stress paradigm, but possible NM interactions with biological systems may result in additional forms of injury. In particular, CNT, a man-made forms of crystalline carbon, are currently attracting intense research efforts because of their unique properties, which make them suitable for many uses in biomedicine and pharmacology. Although CNT stimulate cytokine production and induce inflammatory reactions, they could behave also as conventional fibers, showing the ability to cause lung granulomas and fibrotic reactions in experimental animals. Production and marketing of NM is advancing much more rapidly than research on NM safety. This phenomenon will have a strong impact on the approach of occupational physicians to health risks from NP. In literature increasing evidence suggests that NM are potentially hazardous to humans and that strict industrial hygiene measures should be taken to limit exposure during their manipulation. Moreover, given the uncertainty about the NM features endowed with pathogenetic relevance, the toxicological properties of a specific NP should be evaluated on an individual basis by new screening strategies based on current acquisitions.

Crossover from the Luttinger-liquid to Coulomb-blockade regime in carbon nanotubes.

We develop a theoretical approach to the low-energy properties of one-dimensional electron systems aimed to encompass the mixed features of Luttinger-liquid and Coulomb-blockade behavior observed in the crossover between the two regimes. For this aim, we extend the Luttinger-liquid description by incorporating the effects of a discrete single-particle spectrum. The intermediate regime is characterized by a power-law behavior of the conductance, but with an exponent oscillating with the gate voltage, in agreement with recent experimental observations. Our construction also accounts naturally for the existence of a crossover in the zero-bias conductance, mediating between two temperature ranges where the power-law behavior is preserved but with a different exponent.

Fibrin polymerization is crucial for thrombin generation in platelet-rich plasma in a VWF-GPIb-dependent process, defective in Bernard-Soulier syndrome.

Defective prothrombin consumption has been reported in the proband case of Bernard-Soulier syndrome (BSS). There is no consensus, however, on whether the formation of platelet procoagulant activity (PPA) is impaired in BSS and, if so, whether this is due to the lack of GPIb-V-IX-dependent binding of thrombin or of von Willebrand factor (VWF). We show thrombin generation (TG) in platelet-rich plasma of BSS (BSS-PRP) to be defective provided that fibrin remains present in the reaction mixture and that the giant platelets are not damaged by frequent subsampling. In BSS-PRP addition of (thrombin-free) fibrin did not increase TG as in normal PRP, supporting our previous hypothesis that the interaction of fibrin, VWF and GPIb triggers PPA development. Fibrin formed during the lag phase of TG by a snake venom enzyme which only removed fibrinopeptide A induced an immediate burst of TG, that was inhibited by a monoclonal antibody against GPIb (6D1) that abolishes ristocetin-induced binding of VWF to platelets. Inversely, inhibition of polymerization decreased TG and the residual activity was insensitive to 6D1. We conclude that polymerizing fibrin interacts with VWF so as to activate GPIb.

Experimental study for the feasibility of a crystalline undulator.

We present an idea for creation of a crystalline undulator and report its first realization. One face of a silicon crystal was given periodic microscratches (grooves) by means of a diamond blade. The x-ray tests of the crystal deformation due to a given periodic pattern of surface scratches have shown that a sinusoidal-like shape is observed on both the scratched surface and the opposite (unscratched) face of the crystal; that is, a periodic sinusoidal-like deformation goes through the bulk of the crystal. This opens up the possibility for experiments with high-energy particles channeled in a crystalline undulator, a novel compact source of radiation.

Molecular basis of Glanzmann's Thrombasthenia and current strategies in treatment.

Glanzmann Thrombasthenia, an exceptional inherited platelet disorder is characterized by a complete lack of platelet aggregation due to a defect in the alpha(IIb)beta(3) complex or to a qualitative abnormality of this complex. Advances in molecular biology have permitted to precise the molecular abnormality on alpha(IIb) or beta(3) genes responsible for the disease and have also contributed to a better knowledge of normal platelet physiology. Hemorrhages are the main clinical problem. Current principles of therapeutic management are proposed, with special reference to the risk of platelet alloimmunisation.

Nitric oxide synthase blockade and body fluid volumes

The influence of chronic nitric oxide synthase inhibition with N G-nitro-L-arginine methyl ester (L-NAME) on body fluid distribution was studied in male Wistar rats weighing 260-340 g. Extracellular, interstitial and intracellular spaces, as well as plasma volume were measured after a three-week treatment with L-NAME (70 mg/kg per 24 h in drinking water). An increase in extracellular space (16.1 ± 1.1 vs 13.7 ± 0.6 ml/100 g in control group, N = 12, P<0.01), interstitial space (14.0 ± 0.9 vs 9.7 ± 0.6 ml/100 g in control group, P<0.001) and total water (68.7 ± 3.9 vs 59.0 ± 2.9 ml/100 g, P<0.001) was observed in the L-NAME group (N = 8). Plasma volume was lower in L-NAME-treated rats (2.8 ± 0.2 ml/100 g) than in the control group (3.6 ± 0.1 ml/100 g, P<0.001). Blood volume was also lower in L-NAME-treated rats (5.2 ± 0.3 ml/100 g) than in the control group (7.2 ± 0.3 ml/100 g, P<0.001). The increase in total ratio of kidney wet weight to body weight in the L-NAME group (903 ± 31 vs 773 ± 45 mg/100 g in control group, P<0.01) but not in total kidney water suggests that this experimental hypertension occurs with an increase in renal mass. The fact that the heart weight to body weight ratio and the total heart water remained constant indicates that, despite the presence of high blood pressure, no modification in cardiac mass occurred. These data show that L-NAME-induced hypertension causes alterations in body fluid distribution and in renal mass