Optimal Ways of Safflower Oil Production with Improvement of Press Equipment.

This study aims to improve press equipment for safflower oil production by using a mechanism that optimizes pressure distribution within screw turns. A detailed analysis of the main components of the produced safflower oil was performed, encompassing both quantitative and qualitative assessments. Through the exploration of dependencies governing the safflower oil pressing process on the screw press, the optimal parameters were determined. As a result of the research, the optimal diaphragm gap between the gape cylinder and the pressing screw was determined, with the optimal oil yield percentage achieved at ω = 6.2 rad/s and δ = 5 mm. The study also compared the performance of the existing Dream Modern ODM-01 screw press and its upgraded version by analyzing the extracted oil. The results reveal changes in the quantitative and qualitative composition of the main oil components following the operation of the existing and the modernized screw presses. For instance, the amount of unsaturated fatty acids, such as oleic acid (7.7 ± 0.566%), linoleic acid (85.3 ± 1.185%), and linolenic acid (1.2 ± 0.223%), increased. There was an increase in the presence of inorganic substances in safflower oil: iron (0.023 ± 0.031 mg/kg), phosphorus (0.086 ± 0.059 mg/kg), silicium (0.136 ± 0.075 mg/kg), and others. The findings of this study hold significant commercial value and offer promising prospects for global market implementation.

The Study of Composite Materials Properties Based on Polymers and Nano-Additives from Industrial Wastes from Kazakhstan.

This research is aimed at studying the properties of polymer anticorrosion coatings based on ED-20 resin widely used in practice and industrial wastes. In this work, three basic types of nanoscale nanofillers were chosen: dispersed particles-microsilica, microspheres obtained at Kazakh enterprises, and carbon nanotubes. Physicochemical research methods were used in the research: a laser analyzer for studying the dispersibility of industrial waste and spectrometric research methods. The properties of materials were investigated by standardized methods. The obtained results show that the introduction of microsilica and microspheres obtained at Kazakhstani enterprises, used as additives, improves both the physical and mechanical properties of epoxy composites compared to the standard (control) material. The results of experiments have shown that the optimal content of additives of microsilica and microspheres provides an improvement in the physical and mechanical properties of epoxy composites in comparison with the standard (control) material. Studies have shown that the introduction of microspheres into ED-20 polymer increases impact toughness. The introduction of microsilica into the matrix contributes to the increase of elastic modulus. Experimental studies of optical properties of samples of carbon composite polymer films based on polystyrene (PS) with additives of carbon nanotubes C60 and C70 and multilayer carbon nanotubes were also carried out. The experimental results obtained for the optical properties of polymer composites based on basic polymers from solid waste and carbon nanotubes showed that the optical properties of polymer composites undergo noticeable changes.

Effect of Thermal Activation on the Structure and Electrochemical Properties of Carbon Material Obtained from Walnut Shells.

A simple activation method has been used to obtain porous carbon material from walnut shells. The effect of the activation duration at 400 °C in an atmosphere with limited air access on the structural, morphological, and electrochemical properties of the porous carbon material obtained from walnut shells has been studied. Moreover, the structure and morphology of the original and activated carbon samples have been characterized by SAXS, low-temperature adsorption porosimetry, SEM, and Raman spectroscopy. Therefore, the results indicate that increasing the duration of activation at a constant temperature results in a reduction in the thickness values of interplanar spacing (d002) in a range of 0.38-0.36 nm and lateral dimensions of the graphite crystallite from 3.79 to 2.52 nm. It has been demonstrated that thermal activation allows for an approximate doubling of the specific SBET surface area of the original carbon material and contributes to the development of its mesoporous structure, with a relative mesopore content of approximately 75-78% and an average pore diameter of about 5 nm. The fractal dimension of the obtained carbon materials was calculated using the Frenkel-Halsey-Hill method; it shows that its values for thermally activated samples (2.52, 2.69) are significantly higher than for the original sample (2.17). Thus, the porous carbon materials obtained were used to fabricate electrodes for electrochemical capacitors. Electrochemical investigations of these cells in a 6 M KOH aqueous electrolyte were conducted by cyclic voltammetry, galvanostatic charge/discharge, and impedance spectroscopy. Consequently, it was established that the carbon material activated at 400 °C for 2 h exhibits a specific capacity of approximately 110-130 F/g at a discharge current density ranging from 4 to 100 mA/g.

A Study of the Relationship between the Dynamic Viscosity and Thermodynamic Properties of Palm Oil, Hydrogenated Palm Oil, Paraffin, and Their Mixtures Enhanced with Copper and Iron Fines.

The article presents the results of phase transition studies in which the following substances and their mixtures were tested: 100% palm oil, 100% paraffin, 100% hydrogenated palm oil, 50% palm oil + 50% paraffin, 50% hydrogenated palm oil + 50% palm oil, 33% hydrogenated palm oil + 33% palm oil + 33% soft paraffin, 20% hydrogenated palm oil + 30% palm oil + 50% soft paraffin, 50% hydrogenated palm oil + 50% palm oil + copper, and 50% hydrogenated palm oil + 50% palm oil + iron. The measurements were carried out on a station for testing phase-change materials (PCMs) designed specifically for the analysis of phase changes. Viscosity values were also determined for the tested materials, and their potential impact on heat accumulation was assessed. The primary goal of the experiment was to determine some key thermodynamic parameters, including transition time, transition heat, specific heat, and dynamic viscosity at 58 °C. A one-way ANOVA test confirmed the statistical significance of minimum transition temperature, maximum transition temperature, and phase transition time, validating the reliability and utility of the results. The melting point, crucial for applications involving phase changes, was identified as an important factor. The careful selection of components allows for the customization of properties tailored to specific applications. A significant result is that the analyzed substances with higher specific heat values tend to have a higher average dynamic viscosity. The Pearson correlation coefficient of 0.82 indicated a strong positive association between the average dynamic viscosity and the heat of fusion of the substances examined. This suggests that changes in the heat of fusion significantly influence alterations in dynamic viscosity. Substances with higher specific heat values tend to exhibit higher average dynamic viscosity, emphasizing the direct impact of composition on viscosity.

Modeling of the Efficiency of the Centrifugal Conical Disk Dispenser of Bulk Materials.

Centrifugal disk dispensers are widely used in various tasks of dosing bulk, dispersed materials. The design of the disk depends on the physical and mechanical characteristics of the dosing medium. The work discusses the development of an analytical model of the movement of a material particle along a conical centrifugal disk depending on the kinematic characteristics of the dosing process and the characteristics of the dosing material, as well as experimental confirmation of the theoretical model, which is relevant for the calculation and design of working elements of this type. The obtained system of differential equations is solved using the Runge-Kutta numerical method. Experimental studies were carried out using the method of a planned factorial experiment. The experiment was conducted for three factors at three levels. The feedback criterion was the performance of a centrifugal conical disk dispenser for bulk materials. The disk cone angle was set at 10, 20, and 30°. The disk diameter was 130, 150, and 170 mm, the gap between the disk and the edge of the hopper neck was 6, 8, and 10 mm, and the rotational speed of the conical disk was 0.65, 1.02, and 1.39 rad/s. The dispensing rate of the dispenser ranged from 15 to 770 g/s, depending on the values of the experimental factors. For use in the regression equation of the natural values of the factors, a method of transforming the terms of the equation from coded values to natural ones is provided. The obtained experimental correlation dependencies were checked for reproducibility with Cochrane's test, and the adequacy of the model was checked using Fisher's test. The significance of the coefficients in the correlation equation was evaluated using the Student's t-test. The difference between the experimental data and the results of the theoretical modeling does not exceed 5%. The obtained system of differential equations makes it possible to model the radial velocity of the ascent of bulk material from the conical rotating disk depending on the rotation frequency, disk diameter, and the height of the annular gap between the discharge throat of the hopper and the conical disk. The analytical model enables the modeling of the productivity of the conical dispenser for bulk materials for arbitrary parameters of rotation frequency, disk diameter, and the size of the annular gap between the discharge throat of the hopper and the conical disk.

Development of Gluten-Free Bread Production Technology with Enhanced Nutritional Value in the Context of Kazakhstan.

This research aims to enhance the nutritional value of gluten-free bread by incorporating a diverse range of components, including additives with beneficial effects on human health, e.g., dietary fibers. The research was focused on improving the texture, taste, and nutritional content of gluten-free products by creating new recipes and including novel biological additives. The goal was to develop gluten-free bread with less than 3 ppm gluten content that can be eaten by people suffering from gluten sensitivity. The physical and chemical properties of gluten-free rice, corn, green buckwheat, chickpea, amaranth, and plantain flours were examined to understand their unique characteristics and the possibility of their mixing combination to achieve the desired results. Initially, nine recipes were prepared, and in survey research, four baking recipes were selected and tested. The composition of amino acids in the prepared gluten-free bread was determined. The variant made of corn, green buckwheat flour with plantain was found to be top-rated. Changes in the nutritional content of the new product were analyzed, and general regulations and nutritional values were identified. Experimental baking processes were carried out, leading to the successful formulation of gluten-free bread containing corn, green buckwheat, and plantain flour in a ratio of 40:40:20, meeting gluten-free requirements and demonstrating improved nutritional properties, as well as consumption properties, confirmed by surveys conducted on a group of consumers.

Improving the Technology of Primary Purification of the Safflower Oil Using Secondary Products of Processing on a Biological Basis.

Safflower oil is a very valuable product for the body and human health. It is rich in macro- and microelements, vitamins and minerals, and also has antioxidant properties. The primary purification of safflower oil is an important stage of its production and directly affects the quality of the final product and its storage ability. Purifying safflower oil using a combination of filtration and sedimentation processes in an experimental cone-shaped centrifuge is a new direction in its processing. The purpose of this study was to determine the effects of flax fiber as a filter material for safflower oil. The Akmai variety of the safflower was tested. The results showed that the quality indicators of safflower oil before and after filtration through flax fiber are different. The amount of unsaturated fatty acids such as oleic (18.31 ± 0.874%) and cis-linoleic acid (82.52 ± 1.854%) increased, as well as the content of arginine (2.1), tyrosine (0.57), methionine (0.4), cystine (2.5), tryptophan (2.6), and other amino acids (in oil g per 100 g of protein). The increase in the total amount of phenols (322.12 ± 6 mgEAG/kg of oil) was observed, which directly caused the higher antioxidant activity (42.65 ± 8%) of the safflower oil. These results demonstrate that flax fiber can enrich safflower oil. To find the optimal conditions for safflower oil centrifugation in a cone-shaped sedimentary-filtering centrifuge, the thickness of the flax fiber and the distance between the inner and outer perforated filter rotor were tested. It was found that the optimal and effective thickness of the flax fiber is 1.5 × 107 nm, while the thickness of the sediment is 0.5 × 107 nm.

Porous Structure and Fractal Dimensions of Activated Carbon Prepared from Waste Coffee Grounds.

The present work reports the results of a systematic study on the evolution of the morphological properties of porous carbons derived from coffee waste using a one-pot potassium-hydroxide-assisted process at temperatures in the range of 400-900 °C. Raw materials and obtained carbons were studied by TG, DTG, SEM and nitrogen adsorption porosimetry. The decomposition temperature ranges for hemicellulose, cellulose and lignin as the main component of the feedstock have been established. It is shown that the proposed method for the thermochemical treatment of coffee waste makes it possible to obtain activated carbon with a controllable pore size distribution and a high specific surface area (up to 1050 m2/g). A comparative study of the evolution of the distribution of pore size, pore area and pore volume has been carried out based on the BJH and NL-DFT (slit-like pores approximation) methods. The fractal dimension of the obtained carbons has been calculated by Frenkel-Halsey-Hill method for single-layer and multilayer adsorptions.

Experimental Study on the Cutting Process of Single Triticale Straws.

This paper presents experimental research on cutting a single stalk of triticale straw for the production of biofuel in the process of its compaction using the piston technique. In the first stage of the experimental study of cutting single triticale straws, the variable parameters were the moisture contents of the stem equal to 10% and 40%, the offset between the blade and the counter-blade g, and the linear velocity of the knife blade V. The blade angle and rake angle were equal to α = 0° and ß = 0°. In the second stage, the variables, including the blade angle values α = 0°, 15°, 30°, and 45° and the rake angle values ß = 5°, 15°, and 30°, were introduced. Taking into account the analysis of the distribution of forces on the knife edge leading to the determination of the force quotients Fc″/Fc and Fw/Fc, and on the basis of the optimization performed and the adopted optimization criteria, the optimal knife edge angle α can be determined (at values g = 0.1 mm and V = 8 mm/s) at α ≅ 0° and the angle of attack ß within the range of 5-26°. What the value will be in this range depends on the value of the weight adopted in the optimization. The choice of their values may be decided by the constructor of the cutting device.

On the Influence of Heat Input on Ni-WC GMAW Hardfaced Coating Properties.

Hardfacing is one of the techniques used for part lifecycle elongation. Despite being used for over 100 years, there still is much to discover, as modern metallurgy provides more and more sophisticated alloys, which then have to be studied to find the best technological parameters in order to fully utilize complex material properties. One of the most efficient and versatile hardfacing approaches is Gas Metal Arc Welding technology (GMAW) and its cored-wire equivalent, known as FCAW (Flux-Cored/Cored Arc Welding). In this paper, the authors study the influence of heat input on the geometrical properties and hardness of stringer weld beads fabricated from cored wire consisting of macrocrystalline tungsten carbides in a nickel matrix. The aim is to establish a set of parameters which allow to manufacture wear-resistant overlays with high deposition rates, preserving all possible benefits of this heterogenic material. This study shows, that for a given diameter of the Ni-WC wire, there exists an upper limit of heat input beyond which the tungsten carbide crystals may exhibit undesired segregation at the root.

Tool Wear Issues in Hot Forging of Steel.

Steel forging tools are subjected to a number of tribological wear mechanisms depending on the geometry and surface of the tool and the flow of the material. Thus, there is no single general tribological wear mechanism, and only the predominant wear mechanisms in this case can be indicated. The problem has been known for years, but due to its complexity research on it is still relevant. In this study, the various wear mechanisms of hot work tools are analyzed on the basis of original research. Moreover, the influence of the micro- and macrostructure of the material and of its mechanical, physical, and technological characteristics on susceptibility to a given type of wear is considered. Adhesive wear, wear caused by plastic deformation, mechanical fatigue, thermal fatigue, the influence of hardness, heat treatment, and impact strength on tool wear and the mechanisms causing this wear are discussed in addition to tribological wear mechanisms such as abrasive wear. The influence of thermomechanical history and the characteristics of the tool material, including structural anisotropy, on the wear of these tools is indicated. The analysis of wear mechanisms performed will enable more precise definition of the principles of tool material selection and tool material condition for the hot forging of steel.

Optical and Mechanical Properties of Layered Infrared Interference Filters.

The design and manufacturing technology of interference-absorbing short-wave filters based on a layered composition of Si-SiO on a sapphire substrate of various shapes was developed. A transition layer of SiO was applied to the surface of the substrate, alternating with layers of Si-SiO with an odd number of quarter-wave layers of materials with high (Si) and low refractive indices (SiO), and the application of an outer layer of SiO as an appropriate control of the materials' thickness. The optical properties of the infrared light filter were studied. It was established that the created design of the light filter provides the minimum light transmission in the visible region of the spectrum from 0.38 to 0.78 µm and the maximum in the near infrared region from 1.25 to 5 µm and has stable optical indicators. A method for studying the stress-strain state and strength of a multilayer coating of a light filter under the action of a local arbitrarily oriented load was developed. For simplicity in the analysis and for obtaining results in the analytical form, the one-dimensional model of the configuration "multilayer covering-firm substrate" constructed earlier by authors was used. From a mechanical point of view, the upper protective layer of the multilayer coating was modeled by a flexible plate, and the inner operational composite N-layer was subjected to Winkler's hypothesis about the proportionality of stresses and elastic displacements.

Multiclass Level-Set Segmentation of Rust and Coating Damages in Images of Metal Structures.

This paper describes the combined detection of coating and rust damages on painted metal structures through the multiclass image segmentation technique. Our prior works were focused solely on the localization of rust damages and rust segmentation under different ambient conditions (different lighting conditions, presence of shadows, low background/object color contrast). This paper method proposes three types of damages: coating crack, coating flaking, and rust damage. Background, paint flaking, and rust damage are objects that can be separated in RGB color-space alone. For their preliminary classification SVM is used. As for paint cracks, color features are insufficient for separating it from other defect types as they overlap with the other three classes in RGB color space. For preliminary paint crack segmentation we use the valley detection approach, which analyses the shape of defects. A multiclass level-set approach with a developed penalty term is used as a framework for the advanced final damage segmentation stage. Model training and accuracy assessment are fulfilled on the created dataset, which contains input images of corresponding defects with respective ground truth data provided by the expert. A quantitative analysis of the accuracy of the proposed approach is provided. The efficiency of the approach is demonstrated on authentic images of coated surfaces.

On the Influence of Linear Energy/Heat Input Coefficient on Hardness and Weld Bead Geometry in Chromium-Rich Stringer GMAW Coatings.

Wear of the working surfaces of machinery parts is a phenomenon that cannot be fully countered, only postponed. Among surface lifecycle elongation techniques, hardfacing is one which is most often used in heavy load applications. Hardfaced coating can be applied using different welding approaches or thermal spraying technologies, which differ when it comes to weld bead dimensional precision, layer thickness, process efficiency and material. In this study the authors examine the geometrical behavior and hardness properties of two distinctive chromium-based Gas Metal Arc Welding (GMAW) cored wires. The stringer beads are applied numerically with five levels of linear energy, being a resultant of typical values of welding speed and wire feed, ranging between 250 mm/s to 1250 mm/s (welding speed) and 2 m/min to 10 m/min (wire feed). The samples were cut, etched and measured using a digital microscope and Vickers indenter, additionally the chemical composition was also examined. Hardness was measured at five points in each cutout, giving 40 measurements per sample. The values were analyzed using an ANOVA test as a statistical background in order to emphasize the divergent behavior of the cored wires. It appeared that, despite having less chromium in its chemical composition, wire DO*351 exhibits higher hardness values; however, DO*332 tends to have a more stable geometry across all of the heat input levels.

The Volumetric Wear Assessment of a Mining Conical Pick Using the Photogrammetric Approach.

The rapid wear of conical picks used in rock cutting heads in the mining industry has a significant economic impact in cost effectiveness for a given mineral extraction business. Any mining facility could benefit from decreasing the cost along with a substantial durability increase of a conical pick; thus, the hardfacing method of production and regeneration should be taken into account. In order to automatize the regeneration, the wear rate assessment is necessary. This paper presents a methodology used to create a 3D photogrammetric model of most of the commercially available tangential-rotary cutters in their before and after abrasive exploitation state. An experiment of three factors on two levels is carried out to indicate the proper setup of the scanning rig to obtain plausible results. Those factors are: light level, presence of polarizing filter and the distance from the scanned object. The 3D scan of the worn out specimen is compared to the master model via algorithm developed by the authors. This approach provides more detailed information about the wear mechanism and can help either in roadheader cutting head diagnostics or to develop a strategy and optimize the toolpath for the numerically controlled hardfacing machine.

Modelling of the Fine-Grained Materials Briquetting Process in a Roller Press with the Discrete Element Method.

By using the Altair® EDEM™ software, which implements the discrete element method, modelling and further study of the processes occurring in the roller press's deformation area were carried out. It was shown that the discrete element method makes it possible to accurately describe the phenomena occurring in the area of roller press deformation compared with the finite element method. Models of material compaction in a roller press are developed using calcium hydroxide (slaked lime) and copper ore concentrate. The developed model makes it possible to determine the process's energy parameters and the material's compaction characteristics, taking into account the characteristics of its constituent particles. It was shown that discrete element modelling could be used effectively to create roller presses that provide rational characteristics of the briquetting process, taking into account the properties of the material being briquetted and the operating modes of the equipment. The results of the studies provided the basis for the applicability of the development of the discrete element method for describing the phenomena occurring in roller presses and accelerating the design of press equipment and briquetting technological processes.

Microstructure and Wear Characterization of the Fe-Mo-B-C-Based Hardfacing Alloys Deposited by Flux-Cored Arc Welding.

An analysis of common reinforcement methods of machine parts and theoretical bases for the selection of their chemical composition were carried out. Prospects for using flux-cored arc welding (FCAW) to restore and increase the wear resistance of machine parts in industries such as metallurgy, agricultural, wood processing, and oil industry were presented. It is noted that conventional series electrodes made of tungsten carbide are expensive, which limits their widespread use in some industries. The scope of this work includes the development of the chemical composition of tungsten-free hardfacing alloys based on the Fe-Mo-B-C system and hardfacing technology and the investigation of the microstructure and the mechanical properties of the developed hardfacing alloys. The composition of the hardfacing alloys was developed by extending the Fe-Mo-B-C system with Ti and Mn. The determination of wear resistance under abrasion and impact-abrasion wear test conditions and the hardness measurement by means of indentation and SEM analysis of the microstructures was completed. The results obtained show that the use of pure metal powders as starting components for electrodes based on the Fe-Mo-B-C system leads to the formation of a wear-resistant phase Fe(Mo,B)2 during FCAW. The addition of Ti and Mn results in a significant increase in abrasion and impact-abrasion wear resistance by 1.2 and 1.3 times, respectively.

Optimization of Technological Parameters of the Process of Forming Therapeutic Biopolymer Nanofilled Films.

The prospects of using biopolymer nano-containing films for wound healing were substantiated. The main components of biopolymer composites are gelatin, polyvinyl alcohol, glycerin, lactic acid, distilled water, and zinc oxide (ZnO) nanoparticles (NPs). Biopolymer composites were produced according to various technological parameters using a mould with a chrome coating. The therapeutic properties of biopolymer films were evaluated by measuring the diameter of the protective effect. Physico-mechanical properties were studied: elasticity, vapour permeability, degradation time, and swelling. To study the influence of technological parameters of the formation process of therapeutic biopolymer nanofilled films on their therapeutic and physico-mechanical properties, the planning of the experiment was used. According to the results of the experiments, mathematical models of the second-order were built. The optimal values of technological parameters of the process are determined, which provide biopolymer nanofilled films with maximum healing ability (diameter of protective action) and sufficiently high physical and mechanical properties: elasticity, vapour permeability, degradation time and swelling. The research results showed that the healing properties of biopolymer films mainly depend on the content of ZnO NPs. Degradation of these biopolymer films provides dosed drug delivery to the affected area. The products of destruction are carbon dioxide, water, and a small amount of ZnO in the bound state, which indicates the environmental safety of the developed biopolymer film.

Research on the Influence of Processing Parameters on the Specific Tensile Strength of FDM Additive Manufactured PET-G and PLA Materials.

Fused deposition modeling (FDM) is one of the most accessible additive manufacturing (AM) technologies for processing polymeric materials. It allows processing most of thermoplastic polymers, with polyethylene terephthalate glycol-modified (PET-G) and polylactic acid (PLA). AM parts tend to display anisotropic behavior because of layer-by-layer fabrication and various technological parameters that can be set for 3D print, so it is hard to predict and analyze how the manufactured parts would behave under load. This research presents results of classic tensile strength tests performed on 57 PET-G specimens and 57 PLA specimens manufactured with varying technological parameters such as: printing temperature, print orientation, layer height, and infill percentage. Afterward, a comparative analysis is performed, proposing specific tensile strength (STS) as a benchmark to determine how 3D printed parts strength is varying due to beforementioned parameters, eliminating bias induced by varying weight of specimens. The biggest relative increase of UTS and the biggest relative decrease of STS was noted for variable infill percentage (increasing infill-PLA: 37.27% UTS increase and 30.41% STS decrease; PET-G: 24.42% UTS increase and 37.69% STS decrease). The biggest relative increase of STS between examined parameters was observed for both materials as the printing temperature was increased (27.53% for PLA and 12.69% for PET-G). Similar trends in STS changes were observed for both materials. Obtained data shows which FDM AM parameters are the most important to obtain the biggest UTS of manufactured parts, and those do not overlap with parameters needed to obtain optimal strength-to-weight ratio.

The Thermographic Analysis of the Agglomeration Process in the Roller Press of Pillow-Shaped Briquettes.

When the briquetting process of fine-grained material takes place in the roller press unit, the pressure reached is over a hundred megapascals. This parameter is a result, among other factors, of the geometry of a compaction unit and also the properties of the consolidated material. The pressure of the unit is not constant and the changes in value depend on a given place on the molding surface. By the process of generating different types of pressure on the surface of briquettes, their compaction is different as well. The distribution of temperature on the surface of the briquettes may determine the pressure used locally on them. Nevertheless, the distribution of stress in the briquetting material is still a subject of scientific study. However, it is known that the pressure exerted on the briquette is different for different compaction systems. The article includes authors' further thermography studies on the classical pillow-shaped briquetting process (instead of the saddle-shaped ones that were previously conducted) of four materials (calcium hydroxide and water mixture, mill scale, charcoal fines and starch mixture, as well as a mixture of EAFD, scale, fine coke breeze, molasses, and calcium hydroxide). Immediately after the briquettes left the compaction zone, thermal images were taken of them, as well as forming rollers. Thermograms that were obtained and the variability of temperature at characteristic points of the surface of pillow-shaped briquettes were analyzed. They showed differences in temperature on the surface of briquettes. In all four cases, the highest briquette temperatures were recorded in their upper part, which proves their better densification in this part. The temperature differences between the lower and upper part of the briquettes ranged from 1.8 to 9.7 °C, depending on the mixture.