Nitrogen-Doped Cu2O Thin Films for Photovoltaic Applications.

Cuprous oxide (Cu2O) is a p-type semiconductor with high optical absorption and a direct bandgap of about 2.1 eV, making it an attractive material for photovoltaic applications. For a high-performance photovoltaic device, the formation of low-resistivity contacts on Cu2O thin films is a prerequisite, which can be achieved by, for instance, nitrogen doping of Cu2O in order to increase the carrier concentration. In this work, nitrogen-doped p-type Cu2O thin films were prepared on quartz substrates by magnetron sputter deposition. By adding N2 gas during the deposition process, a nitrogen concentration of up to 2.3 × 1021 atoms/cm3 in the Cu2O thin films was achieved, as determined from secondary ion mass spectroscopy measurements. The effect of nitrogen doping on the structural, optical, and electrical properties of the Cu2O thin films was investigated. X-ray diffraction measurements suggest a preservation of the Cu2O phase for the nitrogen doped thin films, whereas spectrophotometric measurements show that the optical properties were not significantly altered by incorporation of nitrogen into the Cu2O matrix. A significant conductivity enhancement was achieved for the nitrogen-doped Cu2O thin films, based on Hall effect measurements, i.e., the hole concentration was increased from 4 × 1015 to 3 × 1019 cm-3 and the resistivity was reduced from 190 to 1.9 Ω⋅cm by adding nitrogen to the Cu2O thin films.

Metal Oxide Thin-Film Heterojunctions for Photovoltaic Applications.

Silicon-based tandem solar cells incorporating low-cost, abundant, and non-toxic metal oxide materials can increase the conversion efficiency of silicon solar cells beyond their conventional limitations with obvious economic and environmental benefits. In this work, the electrical characteristics of a metal oxide thin-film heterojunction solar cell based on a cuprous oxide (Cu2O) absorber layer were investigated. Highly Al-doped n-type ZnO (AZO) and undoped p-type Cu2O thin films were prepared on quartz substrates by magnetron sputter deposition. The electrical and optical properties of these thin films were determined from Hall effect measurements and spectroscopic ellipsometry. After annealing the Cu2O film at 900 °C, the majority carrier (hole) mobility and the resistivity were measured at 50 cm²/V·s and 200 Ω·cm, respectively. Numerical modeling was carried out to investigate the effect of band alignment and interface defects on the electrical characteristics of the AZO/Cu2O heterojunction. The analysis suggests that the incorporation of a buffer layer can enhance the performance of the heterojunction solar cell as a result of reduced conduction band offset.

Improving carrier transport in Cu2O thin films by rapid thermal annealing.

Cuprous oxide (Cu2O) is a promising material for large scale photovoltaic applications. The efficiencies of thin film structures are, however, currently lower than those for structures based on Cu2O sheets, possibly due to their poorer transport properties. This study shows that post-deposition rapid thermal annealing (RTA) of Cu2O films is an effective approach for improving carrier transport in films prepared by reactive magnetron sputtering. The as-deposited Cu2O films were poly-crystalline, p-type, with weak near band edge (NBE) emission in photoluminescence spectra, a grain size of ~100 nm and a hole mobility of 2-18 cm2 V-1 s-1. Subsequent RTA (3 min) at a pressure of 50 Pa and temperatures of 600-1000 °C enhanced the NBE by 2-3 orders of magnitude, evidencing improved crystalline quality and reduction of non-radiative carrier recombination. Both grain size and hole mobility were increased considerably upon RTA, reaching values above 1 µm and up to 58 cm2 V-1 s-1, respectively, for films annealed at 900-1000 °C. These films also exhibited a resistivity of ~50-200 Ω cm, a hole concentration of ~1015 cm-3 at room temperature, and a transmittance above 80%.

TiO2-coated nanostructures for dye photo-degradation in water.

The photocatalytic efficiency of a thin-film TiO2-coated nanostructured template is studied by dye degradation in water. The nanostructured template was synthesized by metal-assisted wet etching of Si and used as substrate for the deposition of a thin film of TiO2 (10 nm thick) by atomic layer deposition. A complete structural characterization was made by scanning and transmission electron microscopies. The significant photocatalytic performance was evaluated by the degradation of two dyes in water: methylene blue and methyl orange. The relevance of the reported results is discussed, opening the route toward the application of the synthesized nanostructured TiO2 for water purification.

An enhanced photocatalytic response of nanometric TiO2 wrapping of Au nanoparticles for eco-friendly water applications.

We propose a ground-breaking approach by an upside-down vision of the Au/TiO2 nano-system in order to obtain an enhanced photocatalytic response. The system was synthesized by wrapping Au nanoparticles (∼8 nm mean diameter) with a thin layer of TiO2 (∼4 nm thick). The novel idea of embedding Au nanoparticles with titanium dioxide takes advantage of the presence of metal nanoparticles, in terms of electron trapping, without losing any of the TiO2 exposed surface, so as to favor the photocatalytic performance of titanium dioxide. A complete structural characterization was made by scanning electron microscopy, transmission electron microscopy and X-ray diffraction. The remarkable photocatalytic performance together with the stability of the nano-system was demonstrated by degradation of the methylene blue dye in water. The non-toxicity of the nano-system was established by testing the effect of the material on the reproductive cycle of Mytilus galloprovincialis in an aquatic environment. The originally synthesized material was also compared to conventional TiO2 with Au nanoparticles on top. The latter system showed a dispersion of Au nanoparticles in the liquid environment, due to their instability in the aqueous solution that clearly represents an environmental contamination issue. Thus, the results show that nanometric TiO2 wrapping of Au nanoparticles has great potential in eco-friendly water/wastewater purification.

Synthesis, structure and magnetic properties of nanocrystalline YMnO3.

Nanocrystalline YMnO(3) has been prepared by wet chemical synthesis routes to obtain crystallites with sizes from 20 nm to bulk material. The crystal structure of hexagonal YMnO(3) nanocrystallites smaller than 80 nm deviates from bulk material in terms of unit cell distortion and unit cell volume. The ferrielectric displacements of Y(3+) cations along the polar c-axis decays progressively with decreasing size below 100 nm. Indications of weak ferromagnetism in the form of a narrow hysteresis loop and enhanced magnetic susceptibility below 43 K in 20 nm YMnO(3) nanoparticles is attributed to extrinsic effects. Low-temperature annealing of the 20 nm crystallites in an oxidizing atmosphere removed all traces of ferromagnetism, showing that this is not a size-induced property. Finally, formation of the competing metastable orthorhombic phase and the thermodynamically stable hexagonal phase is discussed with respect to oxidizing or reducing conditions during synthesis.