Effect of vehicle amphiphilicity on the dissolution and bioavailability of a poorly water-soluble drug from solid dispersions.

Solid dispersions of a poorly water-soluble drug [REV 5901; alpha-pentyl-3-(2-quinolinylmethoxy)benzenemethanol; 1] in an amphiphilic vehicle [Gelucire 44/14; 2] and in polyethylene glycol (PEG) 1000, PEG 1450, and PEG 8000 were prepared. The vehicle 2 was a mixture of hydrogenated fatty acid esters with a mp of 44 degrees C, and had a HLB value of 14. Compound 1 was dissolved or dispersed in molten vehicles at elevated temperatures. The pulverization and compression of solid dispersions were avoided by encapsulating the hot solutions directly into hard gelatin capsules. At room temperature, the dispersions solidified forming plugs inside the capsules. On storage, greater than 180 mg of 1 remained dissolved per gram of vehicle, while the excess drug formed fine crystals (less than 20 micron). When mixed with water, the dissolved drug separated as a metastable liquid. Due to the surfactant property of 2, the oily form of 1 that separated from this vehicle formed an emulsified system with a globular size of less than 1 micron, while greater than 80% of 1 that separated from the other three formulations coalesced to form large oily masses. As a result of the large difference in surface area, the dissolution rate of 1 in simulated gastric fluid from capsules containing 2 was much higher than that of a PEG-based formulation. The bioavailability (AUC) of 1 in dogs from capsules containing 2 was also higher than that from PEG 1000-based capsules.

Physicochemical basis of increased bioavailability of a poorly water-soluble drug following oral administration as organic solutions.

The physicochemical basis of improvement of the bioavailability of a poorly water-soluble drug [REV 5901; alpha-pentyl-3-(2-quinolinylmethoxy)benzenemethanol; 1] after oral administration as organic solutions was investigated. The drug, which exists in solid and metastable liquid forms, had a pKa value of 3.7 and a solubility of approximately 0.002 mg/mL in water (pH approximately 6) at 37 degrees C. It had appreciable aqueous solubility only at pH values less than 2. The dissolution rate of 1 at pH values greater than 3 was practically zero. On dilution of the water-miscible organic solutions (polyethylene glycol 400 and polysorbate 80) of 1 with aqueous media, the drug instantaneously formed saturated solutions and the excess drug separated as emulsified oily globules. The dispersibility of the globules improved in the presence of surfactants. The average globule size of the oily form of 1 was 1.6 micron or less, as compared with a particle size of 5-10 microns for the solids. Thus, a high surface area of 1 was obtained after oral intake of water-miscible organic solutions. Although 1 was practically insoluble under intestinal pH conditions, its solubility was greatly increased in the presence of bile salts, lecithin, and lipid-digestion mixtures. The high surface area of 1 separating from organic solutions would facilitate its dissolution rate in the presence of biological surfactants and lipids and, therefore, would increase its bioavailability.

Preformulation study of a poorly water-soluble drug, alpha-pentyl-3-(2-quinolinylmethoxy)benzenemethanol: selection of the base for dosage form design.

The physicochemical properties of the base and hydrochloride salt of the poorly water-soluble drug alpha-pentyl-3-(2-quinolinylmethoxy) benzenemethanol (REV 5901) were investigated in order to select an appropriate form of the drug for dosage form development. The pH-solubility profiles of both the base and the salt at 37 degrees C were identical and were in agreement with a pKa value of 3.67 determined by the UV spectral method. The solubility of the drug (approximately 0.002 mg/mL at pH 6) increased gradually with a decrease in pH and reached a value of 0.95 mg/mL at pH 1; at pH values less than 1, the solubility decreased due to the common-ion effect. The pHmax, i.e., the pH of maximum solubility of the drug was, therefore, 1.0. The role of the pHmax in the selection of a salt or base form of a compound was investigated. Due to the conversion of the salt to the base at the surface of the dissolving solid at pH values greater than pHmax, the dissolution rates of both the base and the salt were identical. In the solid state, the salt existed in anhydrous and monohydrate forms; the anhydrous salt converted to the hydrate at greater than 40% relative humidity, and the hydrate lost water at 40-60 degrees C. The thermal properties of the salt were indicative of its potential instability, which was confirmed by accelerated stability studies. The base existed in a stable crystalline solid form, and also in an oily liquid form which converted to crystals on standing.(ABSTRACT TRUNCATED AT 250 WORDS)