ABSTRACT
In this study, we investigate for the first time morphological and compositional changes of silicon quantum dot (SiQD) light-emitting diodes (SiLEDs) upon device operation. By means of advanced transmission electron microscopy (TEM) analysis including energy filtered TEM (EFTEM) and energy dispersive X-ray (EDX) spectroscopy, we observe drastic morphological changes and degradation for SiLEDs operated under high applied voltage ultimately leading to device failure. However, SiLEDs built from size-separated SiQDs operating under normal conditions show no morphological and compositional changes and the biexponential loss in electroluminescence seems to be correlated to chemical and physical degradation of the SiQDs. By contrast, we found that, for SiLEDs fabricated from polydisperse SiQDs, device degradation is more pronounced with three main modes of failure contributing to the reduced overall lifetime compared to those prepared from size-separated SiQDs. With this newfound knowledge, it is possible to devise ways to increase the lifetimes of SiLEDs.
ABSTRACT
We present highly efficient electroluminescent devices using size-separated silicon nanocrystals (ncSi) as light emitting material. The emission color can be tuned from the deep red down to the yellow-orange spectral region by using very monodisperse size-separated nanoparticles. High external quantum efficiencies up to 1.1% as well as low turn-on voltages are obtained for red emitters. In addition, we demonstrate that size-separation of ncSi leads to drastically improved lifetimes of the devices and much less sensitivity of the emission wavelength to the applied drive voltage.
ABSTRACT
We demonstrate a method for the combination of UV-lithography and direct laser writing using two-photon polymerization (2PP-DLW). First a dye doped photoresist is used for UV-lithography. Adding an undoped photoresist on top of the developed structures enables three-dimensional alignment of the 2PP-DLW structures by detecting the spatially varying fluorescence of the two photoresists. Using this approach we show three dimensional alignment by adding 3D structures made by 2PP-DLW to a previously UV-exposed structure. Furthermore, a fluidic system with an integrated total internal reflection mirror to observe particles in a microfluidic channel is demonstrated.
Subject(s)
Lenses , Microfluidic Analytical Techniques/instrumentation , Molecular Imprinting/methods , Photography/methods , Polymers/chemistry , Polymers/radiation effects , Equipment Design , Equipment Failure Analysis , Materials Testing , Photons , Surface Properties/radiation effects , Ultraviolet RaysABSTRACT
White organic light emitting diodes (WOLEDs) suffer from poor outcoupling efficiencies. The use of Bragg-gratings to enhance the outcoupling efficiency is very promising for light extraction in OLEDs, but such periodic structures can lead to angular or spectral dependencies in the devices. Here we present a method which combines highly efficient outcoupling by a TiO(2)-Bragg-grating leading to a 104% efficiency enhancement and an additional high quality microlens diffusor at the substrate/air interface. With the addition of this diffusor, we achieved not only a uniform white emission, but also further increased the already improved device efficiency by another 94% leading to an overall enhancement factor of about 4.
ABSTRACT
We report a simple approach to enhance the out-coupling efficiency in white organic light emitting diodes (WOLEDs). By incorporating MgF2-columns into the ITO-anode and optimizing of their geometry, an overall efficiency enhancement of up to 38% is achieved. In addition, the structuring of the anode does not lead to a change in the electrical behaviour of the devices. As evidenced by goniometric measurements, the angular emission characteristics of the WOLEDs remain unchanged. Simulations, performed with the T-matrix method, reveal the effect of the enhanced outcoupling efficiency of this approach.
Subject(s)
Electrodes , Fluorides/chemistry , Lighting/instrumentation , Magnesium Compounds/chemistry , Semiconductors , Color , Equipment Design , Equipment Failure AnalysisABSTRACT
White organic light emitting diodes (WOLEDs) suffer from poor outcoupling efficiencies. The use of Bragg-gratings to enhance the outcoupling efficiency is very promising for light extraction in OLEDs, but such periodic structures can lead to angular or spectral dependencies in the devices. Here we present a method which combines highly efficient outcoupling by a TiO(2)-Bragg-grating leading to a 104% efficiency enhancement and an additional high quality microlens diffusor at the substrate/air interface. With the addition of this diffusor, we achieved not only a uniform white emission, but also further increased the already improved device efficiency by another 94% leading to an overall enhancement factor of about 4.
ABSTRACT
Bragg gratings incorporated into organic light-emitting diodes (OLEDs) establish a coupling between waveguide modes and useful light (leaky modes). Here we demonstrate that the net coupling direction depends on the OLED stack design. We fabricated two different device structures with gold Bragg gratings. Angle resolved electroluminescence spectra were recorded. For the first device peaks of enhanced emission due to the Bragg grating are observed corresponding to a net energy transfer in direction of the leaky modes. The second device, on the other hand, exhibits dips in the emission spectrum. This reversed direction of energy transfer from the leaky modes to the waveguide modes is explained considering transfer matrix simulations of modal intensity distributions and device emission simulations. An OLED efficiency enhancement is only achieved, if the waveguide mode extraction is dominant.
