Effects of Zn, Mg, and Cu Content on the Properties and Microstructure of Extrusion-Welded Al-Zn-Mg-Cu Alloys.

The study presents the results of research on the influence of different contents of main alloying additions, such as Mg (2 ÷ 2.5 wt.%), Cu (1.2 ÷ 1.9 wt.%), and Zn (5.5 ÷ 8 wt.%), on the strength properties and plasticity of selected Al-Zn-Mg-Cu alloys extruded on a bridge die. The test material variants were based on the EN AW-7075 alloy. The research specimens, in the form of 100 mm extrusion billets obtained with the DC casting method, were homogenized and extrusion welded during direct extrusion on a 5 MN horizontal press. A 60 × 6 mm die cross-section was used, with one bridge arranged in a way to extrude a flat bar with a weld along its entire length. The obtained materials in the F and T6 tempers were characterized in terms of their strength properties, hardness, and microstructure, using EBSD and SEM. The extrusion welding process did not significantly affect the properties of the tested materials; the measured differences in the yield strength and tensile strength between the materials, with and without the welding seam, were up to ±5%, regardless of chemical composition. A decrease in plasticity was observed with an increase in the content of the alloying elements. The highest strength properties in the T6 temper were achieved for the alloy with the highest content of alloying elements (10.47 wt.%), both welded and solid. Significant differences in the microstructure between the welded and solid material in the T6 temper were observed.

FEM Numerical and Experimental Work on Extrusion Welding of 7021 Aluminum Alloy.

Extrusion welding of AlZnMg alloys encounters great technological difficulties in practice associated with high shaping forces and the low quality of longitudinal welds. Three different chemical compositions of 7021 aluminum alloy, differing in terms of Zn and Mg contents, were used in the first stage of the research. The laboratory device modelling the behavior of metal in welding chambers of the porthole die was applied to examine the ability of 7021 alloys to produce high-quality joints. The weldability tests were carried out for different welding temperatures-400, 450 and 500 °C-and for a fixed welding pressure of 300 MPa. The microstructural effects in pressure-welds were evaluated with the use of OM and SEM/EDS. The temperature-pressure parameters in the welding chambers were analyzed by using the FEM method for original porthole dies while extruding tubes with dimensions of Ø50 × 2 mm. Finally, the industrial extrusion trials were performed with examination of the structure and strength of the seam welds. It was found that it is possible to produce high-quality high-strength welds in tubes extruded from AlZnMg alloys in industrial conditions (the strength of welds in the range of 96-101% of the strength of the basic non-welded material) through properly matched alloy chemical composition of the alloy, construction of the porthole dies and temperature-speed conditions of deformation.

Effect of Zirconium Diboride and Titanium Diboride on the Structure and Properties of 316L Steel-Based Composites.

The effect of zirconium diboride (ZrB2) and titanium diboride (TiB2) on the microstructure as well as the physical, mechanical, and tribological properties of composites based on 316 L steel is presented. Each reinforcing phase was added to the base alloy in the amount of 5 wt% and 10 wt%. The composites were fabricated by the SPS process (Spark Plasma Sintering). The results show that the weight fraction of the reinforcing phase affects the physical, mechanical, and tribological properties of the sintered composites. The sintered materials were characterized by a very high level of density. The addition of TiB2 has proved to be effective in increasing the hardness and compressive strength of the composites. The hardness of the composites with the addition of 10% TiB2 increased by 100% compared to the hardness of sintered 316L steel. It was found that introducing ZrB2 to the steel matrix significantly improved the wear resistance of the composites. The results showed that compared to 316L steel with the wear rate of 519 × 10-6 mm3/Nm, the wear rate of the composites containing 10% ZrB2 decreased more than twice, i.e., to 243 × 10-6 mm3/Nm.

Microstructure, Mechanical and Corrosion Properties of Copper-Nickel 90/10 Alloy Produced by CMT-WAAM Method.

In the case of copper and its alloys, Wire Arc Additive Manufacturing (WAAM) 3D printing technology is mainly used to produce elements for the maritime industry and research has focused on the use of Cu-Al alloys. There is little information devoted to the use of Cu-Ni alloys in this technology, which are also widely used in the maritime industry. In this work, tests were carried out on the microstructure, mechanical properties, and corrosion properties in a 1M NaCl solution of Cu-Ni 90/10 alloy 3D walls printed using the WAAM method. The obtained objects are characterized by a microstructure with elongated column grains and particles of the Ni-Ti phase, hardness in the range of 138-160 HV10, ultimate tensile strength of 495-520 MPa, yield strength of 342-358 MPa, elongation of 16.6-17.9%, and a low average corrosion rate of 7.4 × 10-5 mm/year. The work shows that it is possible to obtain higher mechanical properties of Cu-Ni 90/10 alloy 3D objects produced using the WAAM method compared to cast materials, which opens up the possibility of using this alloy to produce objects with more complex shapes and for use in corrosive working conditions.

Ultrafine-Grained Microstructures of Al-Cu Alloys with Hypoeutectic and Hypereutectic Composition Produced by Extrusion Combined with Reversible Torsion.

In this study, binary as-cast Al­Cu alloys: Al25Cu (Al­25%Cu) and Al45Cu (Al­45%Cu) (in wt%) were severely plastically deformed by extrusion combined with a reversible torsion (KoBo) method to produce an ultrafine-grained structure (UFG). The binary Al­Cu alloys consist of α-Al and intermetallic Al2Cu phases. The morphology and volume fraction of α-Al and Al2Cu phases depend on the Cu content. The KoBo process was carried out using extrusion ratios of λ = 30 and λ = 98. The effect of phase refinement has been studied by means of scanning electron microscopy with electron backscattering diffraction and scanning transmission electron microscopy. The mechanical properties were assessed using compression tests. Detailed microstructural analysis shows that after the KoBo process, a large number fraction of high-angle boundaries (HABs) and a very fine grain structure (~2­4 µm) in both phases are created. An increase of λ ratio during the KoBo processing leads to a decrease in average grain size of α-Al and Al2Cu phases and an increase in fraction of HABs. UFG microstructure and high fraction of HABs provide the grain boundary sliding mechanism during KoBo deformation. UFG microstructure contributes to the enhanced mechanical properties. Compressive strength (Rc) of Al25Cu alloy increases from 172 to 340 MPa with an increase of λ. Compressive strain (Sc) for Al25Cu alloy increased from 35 to 67% with an increase of λ. High fraction of intermetallic phase in Al45Cu alloy was responsible for room temperature strengthening of alloy and low compressive strain. The deformed Al45Cu alloy with λ = 30 showed that Rc is 194 MPa and Sc is equal to 10%.

Non-Equilibrium Crystallization of Monotectic Zn-25%Bi Alloy under 600 g.

This study investigated the influence of supergravity on the segregation of components in the Zn-Bi monotectic system and consequently, the creation of an interface of the separation zone of both phases. The observation showed that near the separation boundary, in a very narrow area of the order of several hundred microns, all types of structures characteristic for the concentration range from 0 to 100% bismuth occurred. An additional effect of crystallization in high gravity is a high degree of structural order and an almost perfectly flat separation boundary. This is the case for both the zinc-rich zone and the bismuth-rich zone. Texture analysis revealed the existence of two privileged orientations in the zinc zone. Gravitational segregation also resulted in a strong rearrangement of the heavier bismuth to the outer end of the sample, leaving only very fine precipitates in the zinc region. For comparison, the results obtained for the crystallization under normal gravity are given. The effect of high orderliness of the structure was then absent. Despite segregation, a significant part of bismuth remained in the form of precipitates in the zinc matrix, and the separation border was shaped like a lens. The described method can be used for the production of massive bimaterials with a directed orientation of both components and a flat interface between them, such as thermo-generator elements or bimetallic electric cell parts, where the parameters (thickness) of the junction can be precisely defined at the manufacturing stage.

Microstructure, Mechanical Properties, and Corrosion Resistance of Thermomechanically Processed AlZn6Mg0.8Zr Alloy.

The paper presents results of the investigations on the effect of low-temperature thermomechanical treatment (LTTT) on the microstructure of AlZn6Mg0.8Zr alloy (7000 series) and its mechanical properties as well as electrochemical and stress corrosion resistance. For comparison of the LTTT effect, the alloy was subjected to conventional precipitation hardening. Comparative studies were conducted in the fields of metallographic examinations and static tensile tests. It was found that mechanical properties after the LTTT were better in comparison to after conventional heat treatment (CHT). The tested alloy after low-temperature thermomechanical treatment with increasing plastic deformation shows decreased electrochemical corrosion resistance during potentiodynamic tests. The alloy after low-temperature thermomechanical treatment with deformation degree in the range of 10 to 30% is characterized by a high resistance to stress corrosion specified by the level of PSCC indices.