Decontamination Effect of Hypochlorous Acid Dry Mist on Selected Bacteria, Viruses, Spores, and Fungi as Well as on Components of Electronic Systems.

This publication presents the effect of hypochlorous acid dry mist as a disinfectant on selected bacteria, viruses, spores, and fungi as well as on portable Microlife OXY 300 finger pulse oximeters and electronic systems of Raspberry Pi Zero microcomputers. The impact of hypochlorous acid on microbiological agents was assessed at concentrations of 300, 500, and 2000 ppm of HClO according to PN-EN 17272 (Variant I). Studies of the impact of hypochlorous acid fog on electronic components were carried out in an aerosol chamber at concentrations of 500 ppm and 2000 ppm according to two models consisting of 30 (Variant II) and 90 fogging cycles (Variant III). Each cycle included the process of generating a dry mist of hypochlorous acid (25 mL/m3), decontamination of the test elements, as well as cleaning the chamber of the disinfectant agent. The exposure of the materials examined on hypochlorous acid dry mist in all variants resulted in a decrease in the number of viruses, bacteria, spores, and fungi tested. In addition, the research showed that in the variants of hypochlorous acid fogging cycles analyzed, no changes in performance parameters and no penetration of dry fog of hypochlorous acid into the interior of the tested medical devices and electronic systems were observed.

Ciprofloxacin-, Cefazolin-, and Methicilin-Soaked Graphene Paper as an Antibacterial Medium Suppressing Cell Growth.

This paper presents the results of research on the impact of graphene paper on selected bacterial strains. Graphene oxide, from which graphene paper is made, has mainly bacteriostatic properties. Therefore, the main goal of this research was to determine the possibility of using graphene paper as a carrier of a medicinal substance. Studies of the degree of bacterial inhibition were performed on Staphylococcus aureus and Pseudomonas aeruginosa strains. Graphene paper was analyzed not only in the state of delivery but also after the incorporation of the antibiotics ciprofloxacin, cefazolin, and methicillin into its structures. In addition, Fourier-Transform Infrared Spectroscopy, contact angle, and microscopic analysis of bacteria on the surface of the examined graphene paper samples were also performed. Studies have shown that graphene paper with built-in ciprofloxacin had a bactericidal effect on the strains of Staphylococcus aureus and Pseudomonas aeruginosa. In contrast, methicillin, as well as cefazolin, deposited on graphene paper acted mainly locally. Studies have shown that graphene paper can be used as a carrier of selected medicinal substances.

Laser Emission Spectroscopy of Graphene Oxide Deposited on 316 Steel and Ti6Al4V Titanium Alloy Suitable for Orthopedics.

This paper presents the results of an analysis of carbon (in the form of graphene oxide) deposited on the surface of threads made from stainless steel 316 and titanium alloy Ti6Al4V used in orthopedics using Laser Induced Breakdown Spectroscopy (LIBS). The aim of the article is to indicate the possibility of using the LIBS spectra for the study of thin layers, including graphene derivatives and other elements. Stratigraphic measurements allowed the detection of differences in the spectra peaks of individual elements, not only in the surface layer itself and in the native material, but also in the intermediate layer connecting the two layers. Due to the clear difference in the outline of the spectrum of graphene oxide and the spectrum of the native material of the samples analyzed, a clear incorporation of carbon atoms into the surface layer was observed. A factor analysis was performed, which confirmed the incorporation of graphene oxide into the surface layer of the native material of the elements examined.

Optical Methods of Methane Detection.

Methane is the most frequently analyzed gas with different concentrations ranging from single ppm or ppb to 100%. There are a wide range of applications for gas sensors including urban uses, industrial uses, rural measurements, and environment monitoring. The most important applications include the measurement of anthropogenic greenhouse gases in the atmosphere and methane leak detection. In this review, we discuss common optical methods used for detecting methane such as non-dispersive infrared (NIR) technology, direct tunable diode spectroscopy (TDLS), cavity ring-down spectroscopy (CRDS), cavity-enhanced absorption spectroscopy (CEAS), lidar techniques, and laser photoacoustic spectroscopy. We also present our own designs of laser methane analyzers for various applications (DIAL, TDLS, NIR).

Fluorescence Methods for the Detection of Bioaerosols in Their Civil and Military Applications.

The article presents the history of the development and the current state of the apparatus for the detection of interferents and biological warfare simulants in the air with the laser-induced fluorescence (LIF) method. The LIF method is the most sensitive spectroscopic method and also enables the measurement of single particles of biological aerosols and their concentration in the air. The overview covers both the on-site measuring instruments and remote methods. The spectral characteristics of the biological agents, steady-state spectra, excitation-emission matrices, and their fluorescence lifetimes are presented. In addition to the literature, we also present our own detection systems for military applications.

A Study on the Photopolymerization Kinetics of Selected Dental Resins Using Fourier Infrared Spectroscopy (FTIR).

The aim of the presented study was a comparative analysis of the polymerization kinetics of dental resin-based composites currently used in dentistry in different environmental conditions (irradiance, activation time, layer thickness). The photopolymerization kinetics of eleven dental resins were investigated using a Woodpecker LED source. The DC was measured by FTIR in transmission mode and attenuated total reflection (ATR) from 5 s to 7 days. In the transmission mode, the spectra from parallel optical layers (about 0.2 mm thick) of samples placed between the KBr crystals were recorded. In the reflection mode, an ATR attachment with a diamond window was used. The DC calculation method was applied based on the application of a monomer absorption band at 1638 cm-1 (stretching vibration double bond C=C of the vinyl group) without using a reference band. The data were analyzed by performing an ANOVA test comparison between sample groups at the significance level α = 0.05. For all tested materials, the polymerization kinetics consist of three stages. The fastest stage occurs during the irradiation, and the achieved DC value is 70-75% of the maximum value 5 s after the irradiation. Another 15-20% DC increase at a moderate speed takes about 15-20 min. There is also a very slow further increase in DC of 5-10% within 5 days after irradiation. For 8 out of the 11 tested fillings, the optimal photopolymerization conditions are as follows: a power density of 400 or 1000 mW/cm2; an exposure time of 10 s; and a thickness of the irradiated resin layer of up to 2 mm. The influence of various conditions and factors on the reaction kinetics is dominant only in the early, rapid phase of the conversion. After longer times, the DC values gradually level out under different light conditions. The DC of the dental resins are dependent on the irradiance, light source, filler type, time after irradiance, and monomer thickness.

Studies on the Effect of Graphene Oxide Deposited on Gold and Nickel Microsieves on Prostate Cancer Cells DU 145.

This work shows the effect of graphene oxide deposition on microsieves' surfaces of gold and nickel foils, on DU 145 tumor cells of the prostate gland. The sieves were made by a laser ablation process. The graphene oxide (GO) deposition process was characterized by the complete covering of the inner edges of the microholes and the flat surface between the holes with GO. Electron microscanning studies have shown that due to the deposition method applied, graphene oxide flakes line the interior of the microholes, reducing the unevenness of the downstream surfaces during the laser ablation process. The presence of graphene oxide was confirmed by Fourier infrared spectroscopy. During the screening (sieving) process, the microsieves were placed in a sieve column. Gold foil is proven to be a very good material for the screening of cancer cells, but even more so after screening as a substrate for re-culture of the DU 145. This allows a potential recovery of the cells and the development of a targeted therapy. The sieved cells were successfully grown on the microsieves used in the experiment. Graphene oxide remaining on the surface of the nickel sieve has been observed to increase the sieving effect. Although graphene oxide improved separation efficiency by 9.7%, the nickel substrate is not suitable for re-culturing of the Du 145 cells and the development of a targeted therapy compared to the gold one.

Applications of Laser-Induced Fluorescence in Medicine.

Fluorescence is the most sensitive spectroscopic method of analysis and fluorescence methods. However, classical analysis requires sampling. There are new needs for real-time analyses of biological materials, without the need for sampling. This article presents examples of proprietary applications of laser-induced fluorescence (LIF) in medicine with such methods. A classic example is the analysis of photosensitizers using the photodynamic treatment method (PDT). The level and kinetics of accumulation and excretion of sensitizers in the body are examined, as well as the optimal exposure time after the application of compounds. The LIF method is also used to analyze endogenous fluorophores; it has been used to detect neoplasms, e.g., lung cancer or gynecological and dermatological diseases. Furthermore, it is used for the diagnosis of early stages of tooth decay or detection of fungi. The article will present the construction of sensors based on the LIF method-fiber laser spectrometers and investigated fluorescence spectra in individual applications. Examples of fluorescence imaging, e.g., dermatological, and dental diagnostics and measuring systems will be presented. The advantage of the method is it has greater sensitivity and easily detects lesions early compared to the methods used in observing the material in reflected light.

A Reliable Method of Measuring the Conversion Degrees of Methacrylate Dental Resins.

The main aim of the study was to implement the most reliable method of measuring the degrees of conversion during photopolymerization of dental fillings. Contrary to the methods used so far, the method is based only on comparison with the monomer absorbance spectrum without reference bands. Another aim of the study was to prepare a comparative analysis of the polymerization kinetics of dental resins under various light sources and different environmental conditions (irradiance, light dose, temperature), with estimation of the degrees of conversion (DC) of the resins being the main metric. HRi Universal Enamel (UE2) and HRi Universal Dentine (UD2) were examined under two different types of light sources used in dentistry, LED and halogen. DC was measured by Fourier transform infrared spectroscopy (FTIR) in transmission mode from 5 s up to 7 days. Spectra were recorded from the parallel optical layers of samples that were placed between the KBr crystals. The results are expressed by the changes in the absorbance spectrum during the polymerization and the calculated conversion rates. The results of each experiment were averaged from three separate measurements of three samples, during which the samples were illuminated under identical conditions. The data were analyzed by performing ANOVA test comparisons between sample groups at the significance level α = 0.05. The degree of conversion of the UD2 resin was higher than that of UE2 for each experimental condition, but there was no statistically significant difference between the DC of those materials (p > 0.05). There was statistically significant difference (p < 0.01) in the DC caused by LED and halogen light sources producing the same light doses (38 J/cm2). This was the result of different features of light transmission to the filler in the resin composite. The efficacy of the LED source is twice as high as that of the halogen light source. Maximal DC without any other differences in conditions, such as resin type or light source, reached around 70% for temperatures of 22−37 °C. For 37 °C, this took 24 h, which is a contrast to the 7 days it took for 23 °C. The influences of different conditions and factors on reaction kinetics are only strong in the early and the rapid stage of conversion. The optimal time of irradiance using either light source is 20 s for a monolayer, and its thickness should not exceed 2 mm.

Fatigue Life of Austenitic Steel 304 Bolts Strengthened by Surface Treatment with Graphene Oxide Layer and Surface Shot Peening.

This paper presents the results of investigations of the effect of graphene oxide and surface shot peening on the mechanical properties and fatigue life of bolts made of austenitic 304 steel. An innovative method for the uniform deposition of graphene oxide on screws is presented. The process involved activating the surface using plasma and then performing graphene oxide deposition using centrifugal force and vacuum drying. The screw specimens prepared in this way were subjected to a surface peening process. Comparative studies have shown that the combination of graphene oxide deposition and shot peening processes results in an increase in fatigue life of approximately 42 ÷ 275% (depending on the stress amplitude level) compared to the as-delivered samples. The results presented are promising and may provide a basis for further research on the application of graphene and its derivatives to increase fatigue life and improve the mechanical properties of machine components.

Study on the Effect of Deposited Graphene Oxide on the Fatigue Life of Austenitic Steel 1.4541 in Different Temperature Ranges.

This paper presents the effect of deposited graphene oxide coating on fatigue life of austenitic steel 1.4541 at 20 °C, 100 °C, and 200 °C. The study showed a decrease in the fatigue life of samples with a deposited graphene oxide layer in comparison with reference samples at 20 °C and 100 °C. However, an increase in fatigue life of samples with a deposited graphene oxide layer in comparison with reference samples occurred at 200 °C. This relationship was observed for the nominal stress amplitude of 370 and 420 MPa. Measurements of temperature during the tensile failure of the sample and microfractographic analysis of fatigue fractures were performed. Tests have shown that graphene oxide deposited on the steel surface provides an insulating layer. A higher temperature of the samples with a deposited graphene oxide layer was observed during fracture compared to the reference samples.

Graphene Oxide Aerosol Deposition and its Influence on Cancer Cells. Preliminary Results.

This paper presents the results of the interaction of graphene oxide (GO) on MDA-MB-231 and SW-954 cancer cell lines. The tests were carried out in two variants. In the first one, GO was sprayed on a Petri dish and then, the cancer cell lines were cultured. In the second variant, the cells were covered with an aerosol containing GO. In both variants, cancer cell lines were incubated and tested every 24, 48, and 72 h. After each time period, cell viability and surface morphology were measured. The tests after 72 h showed that coating with GO aerosol caused a reduction in cell viability by 52.7% and 26.4% for MDA-MB-231 and SW-954 cancer cell lines, respectively, with respect to a reference sample (without the influence of GO aerosol). Tests where GO is a culture medium demonstrated a decrease in cell viability by approximately 4.3% compared to a reference sample for both considered cell lines.

Fast, reagentless and reliable screening of "white powders" during the bioterrorism hoaxes.

The classification of dry powder samples is an important step in managing the consequences of terrorist incidents. Fluorescence decays of these samples (vegetative bacteria, bacterial endospores, fungi, albumins and several flours) were measured with stroboscopic technique using an EasyLife LS system PTI. Three pulsed nanosecond LED sources, generating 280, 340 and 460nm were employed for samples excitation. The usefulness of a new 460nm light source for fluorescence measurements of dry microbial cells has been demonstrated. The principal component analysis (PCA) and hierarchical cluster analysis (HCA) have been used for classification of dry biological samples. It showed that the single excitation wavelength was not sufficient for differentiation of biological samples of diverse origin. However, merging fluorescence decays from two or three excitation wavelengths allowed classification of these samples. An experimental setup allowing the practical implementation of this method for the real time fluorescence decay measurement was designed. It consisted of the LED emitting nanosecond pulses at 280nm and two fast photomultiplier tubes (PMTs) for signal detection in two fluorescence bands simultaneously. The positive results of the dry powder samples measurements confirmed that the fluorescence decay-based technique could be a useful tool for fast classification of the suspected "white powders" performed by the first responders.

Comparison of fluorescence spectroscopy and FTIR in differentiation of plant pollens.

Spectroscopic techniques are under investigation on possibility of differentiation of airborne particles. This paper describes pollen discrimination among others bio-particles in laboratory conditions. Pollen samples were characterized with UV-Vis fluorescence, drift and KBr pellet techniques of infrared spectroscopy. Principal Component Analysis of UV-Vis fluorescence and FTIR spectra revealed that pollens can be distinguished from other bio-materials with use of these methods. Both methods resulted in similar classification capability. Combined FTIR and fluorescence data analysis did not improve the discrimination between pollen allergens and other airborne biological materials.

Classification of the biological material with use of FTIR spectroscopy and statistical analysis.

Rapid detection and discrimination of dangerous biological materials such as bacteria and their spores has become a security aim of considerable importance. Various analytical methods, including FTIR spectroscopy combined with statistical analysis have been used to identify vegetative bacteria, bacterial spores and background interferants. The present work discusses the application of FTIR technique performed in reflectance mode using Horizontal Attenuated Total Reflectance accessory (HATR) to the discrimination of biological materials. In comparison with transmission technique the HATR is more rapid and do not require the sample destruction, simultaneously giving similar absorbance bands. HATR-FTIR results combined with statistical analysis PCA and HCA demonstrate that this combination provides novel and accurate microbial identification technique.

Influence of photodynamic effect on biological activity of PBR-PP complexes.

The aim of this study was to examine the influence of photodynamic effect on biological activity of PBR-PP complexes. These measurements were performed in pH dependent environment. Constant concentration of solubilized receptor was titrated with increasing concentration of porphyrins (PPIX, Hp, PP(Arg)(2), Hp(Arg)(2), PP(Gly)(2), PP(Ala)(2), PP(Ser)(2), PP(Phe)(2)) and binding constants were calculated. PBP-PP mixtures were illuminated with 3 J, 5 J or 10 J of blue light and changes in protein fluorescence was recorded. Experimental data were fitted to weak and strong binding models. As a result for all derivatives weak binding model was the best fitted. The strongest binding showed PPIX in pH 7.4 and with pH drop binding constants showed greater values for all examined derivatives. Out of amino acid derivatives the strongest binding was noticed for PP(Gly)(2) and PP(Phe)(2) and for the last one pH influence was not observed.

Interactions of protoporphyrin IX and its derivatives with benzodiazepine receptor.

The aim of this study was to determine binding affinities of the Peripheral benzodiazepine receptor (PBR) with protoporphyrin IX, haematoporphyrin (Hp), and two arginized derivatives: Hp(Arg)(2) and PP(Arg)(2). The quenching of protein fluorescence was used to measure association constants during titration of PBR solution with PP derivatives in a function of concentration. The experimental data was fitted to theoretical curves, assuming strong and weak binding model with one binding site. As a result of this early study affinity constants were determined. The highest affinity toward PBR showed PPIX and Hp, Hp(Arg)(2), PP(Arg)(2) lower, respectively. Changes in pH of protein solution resulted in decrease of association constants in nearly all examined derivatives.

Interactions of peripheral-type benzodiazepine receptor with diamino acid derivatives of protoporphyrin IX.

The aim of this study was to examine and determine binding affinities of the peripheral benzodiazepine receptor (PBR) with diamino acid derivatives of protoporphyrin IX with general structure PP(AA)(2) in a function of environmental pH changes. Fluorescence intensity was used as a measure of protein association constant. Decrease in protein fluorescence, after titration with increasing concentration of porphyrins, gave evidence of interactions between PBR and examined ligands. Experimental data were fitted to theoretical curves, assuming different models of interactions. All examined ligands were best fitted to weak binding model. Increase in environmental acidity resulted in changes in association constants. For all examined derivatives association constants were at least twice higher in pH 5.5 as compared to pH 7.4 and 6.5.