ABSTRACT
Techniques of liver replacement would benefit patients awaiting donor livers and may be a substitute for transplantation in patients whose livers can regenerate. Poly(lactic-co-glycolic acid) (PLGA) copolymers are biodegradable and have been shown to be useful as scaffolds for seeding and culturing various types of cells. In this study, foam disks were prepared from PLGA (lactic-to-glycolic mole ratio of 85:15) by lyophilization of benzene (5% w/v) solutions. These disks were then used as scaffolds for rat hepatocyte culture. Foams were coated with either a type I collagen gel (0.1% w/v), coated with gelatin (5% w/v), or treated with oxygen plasma (25 W, 90 s) to modify their surface chemistry and wettability. The disks were then seeded with rat hepatocytes (10(6)/mL) and cultured for a period of 2 weeks. All surface treatments resulted in increased hydrophilicity, the greatest being obtained by collagen treatment (contact angle < 10 degrees ), and a minimal decrease in void fraction (5%). DNA content after a 2-week culture period increased proportionally with the wettability of the treated foam surface. Urea synthesis in untreated foams averaged 15.3 +/- 2.3 microg/h/microg DNA, which was significantly higher than that for controls, whereas gelatin and collagen treated foams exhibited urea synthetic rates below the control levels at all times. The DNA content decreased significantly by about 50% between days 1 and 12. PLGA foams, treated and untreated, represent a promising scaffold for scaling up hepatocyte cultures.
Subject(s)
Biocompatible Materials , Lactic Acid , Liver/physiology , Polyglycolic Acid , Polymers , Tissue Engineering , Animals , Bioprosthesis , Cell Adhesion/physiology , Cells, Cultured , Liver/cytology , Liver Transplantation , Male , Polylactic Acid-Polyglycolic Acid Copolymer , Rats , Rats, Inbred F344ABSTRACT
Biodegradable bone plates were prepared as semi-interpenetrating networks (SIPN) of crosslinked polypropylene fumarate (PPF) within a host matrix of either poly(lactide-co-glycolide)-85:15 (PLGA) or poly(1-lactide-co-d,l-lactide)-70:30 (PLA) using N-vinylpyrrolidone (NVP), ethylene glycol dimethacrylate (EGDMA), 2-hydroxyethyl methacrylate (HEMA), and methyl methacrylate (MMA) as crosslinking agents. Hydroxyapatite (HAP), an inorganic filler material, was used to further augment mechanical strength. The control crosslinking agent (NVP) was replaced partially and totally with other crosslinking agents. The amount of crosslinking agent lost, the characterization change in the mechanical properties and the dimensional stability of the bone plates after in vitro treatment was calculated. The optimum crosslinking agent was selected on the basis of low in vitro release of NVP from SIPN matrix. Bone plates were then prepared using this crosslinking agent at 5 MPa pressure and at temperatures between 100-140 degrees C to determine if there was any augmentation of mechanical properties in the presence of the crosslinked network. In vitro analysis showed that 90% of the crosslinking agent was lost on plates using NVP as a crosslinking agent. This loss was reduced to 50% when NVP was partially replaced with EGDMA or MMA. EGDMA was determined to be superior because (1) its low release as a crosslinking agent, (2) flexural plate strength of 50-67 MPa, (3) flexural modulus of 7-13 GPa, and (4) manufacturability stiffness of 300-600 N/m. HAP-loading resulted in an additional increase in values of mechanical parameters. Substituting PLGA with PLA in the PPF-SIPN did not show any additional improvement of mechanical properties.
Subject(s)
Absorbable Implants , Biocompatible Materials/chemistry , Bone Plates , Cross-Linking Reagents/chemistry , Durapatite/chemistry , Elasticity , Equipment Design , Fumarates/chemistry , Hot Temperature , Humans , Lactic Acid/chemistry , Methacrylates/chemistry , Methylmethacrylate/chemistry , Pliability , Polyesters/chemistry , Polyglycolic Acid/chemistry , Polylactic Acid-Polyglycolic Acid Copolymer , Polymers/chemistry , Polypropylenes/chemistry , Pressure , Pyrrolidinones/chemistry , Stress, MechanicalABSTRACT
Alteration of the geometrical surface configuration of cortical bone allografts may improve incorporation into host bone. A porous biodegradable coating that would maintain immediate structural recovery and subsequently allow normal graft healing and remodeling by promoting bony ingrowth could provide an osteoconductive surface scaffold. We investigated the feasibility of augmenting cortical bone grafts with osteoconductive biodegradable polymeric scaffold coatings. Three types of bone grafts were prepared: Type I--cortical bone without coating (control), Type II--cortical bone coated with PLGA-foam, Type III--cortical bone coated with PPF-foam. The grafts were implanted into the rat tibial metaphysis (16 animals for each type of bone graft). Post-operatively the animals were sacrificed at 2 weeks and 4 weeks (8 animals for each type of bone graft at each time point). Histologic and histomorphometric analysis of grafts showed that the amount of new bone forming around the foam-coated grafts was significantly higher than in the control group (uncoated; p < 0.02). Although both foam formulations were initially equally osteoconductive, PLGA-based foam coatings appeared to have degraded at two weeks postoperatively, whereas PPF-based foam coatings were still present at 4 weeks postoperatively. While significant resorption was present in control allografts with little accompanying reactive new bone formation, PLGA-coated bone grafts showed evidence of bone resorption and subsequent bony ingrowth earlier than those coated with PPF-based foams suggesting that PPF-coated cortical bone grafts were longer protected against host reactions resulting in bone resorption.
