ABSTRACT
Online techniques for the quantitative analysis of reaction products have many advantages over offline methods. However, owing to the low product formation rates in electrochemical reactions, few of these techniques can be coupled to electrochemistry. An exception is differential electrochemical mass spectrometry (DEMS), which gains increasing popularity not least because of its high time resolution in the sub-second regime. DEMS is often combined with a dual thin-layer cell (a two-compartment flow cell), which helps to mitigate a number of problems that arise due to the existence of a vacuum|electrolyte interface. However, the efficiency with which this cell transfers volatile reaction products into the vacuum of the mass spectrometer is far below 100%. Therefore, a calibration constant that considers not only the sensitivity of the DEMS setup but also the transfer efficiency of the dual thin-layer cell is needed to translate the signals observed in the mass spectrometer into electrochemical product formation rates. However, it can be challenging or impossible to design an experiment that yields such a calibration constant. Here, we show that the transfer efficiency of the dual thin-layer cell depends on the diffusion coefficient of the analyte. Based on this observation, we suggest a two-point calibration method. That is, a plot of the logarithm of the transfer efficiencies determined for H2 and O2 versus the logarithm of their diffusion coefficients defines a straight line. Extrapolation of this line to the diffusion coefficient of another analyte yields a good estimate of its transfer efficiency. This is a versatile and easy calibration method, because the transfer efficiencies of H2 and O2 are readily accessible for a large range of electrode-electrolyte combinations.
ABSTRACT
To date the electroactive species of selective aldehyde oxidation to carboxylates at gold electrodes is usually assumed to be the diolate. It forms with high concentration only in very alkaline electrolytes, when OH- binds to the carbonyl carbon atom. Accordingly, the electrochemical upgrading of biomass-derived aldehydes to carboxylates is believed to be limited to very alkaline electrolytes at many electrode materials. However, OH- -induced aldehyde decomposition in these electrolytes prevents application of electrochemical aldehyde oxidation for the sustainable upgrading of biomass to value-added chemicals at industrial scale. Here, we demonstrate the successful oxidation of aliphatic aldehydes at a rotating gold electrode at pHâ 12, where only 1 % of the aldehyde resides as the diolate species. This concentration is too small to account for the observed current, which shows that also other aldehyde species (i. e., the geminal diol and the non-hydrated aldehyde) are electroactive. This insight allows developing strategies to omit aldehyde decomposition while achieving high current densities for the selective aldehyde oxidation, making its future industrial application viable.
ABSTRACT
In this work, we employ differential electrochemical mass spectrometry (DEMS) to track the real-time evolution of CO at nanoporous gold (NpAu) catalysts with varying pore parameters (diameter and length) during the electrochemical CO2 reduction reaction (CO2RR). We show that due to the increase in the local pH with increasing catalyst roughness, NpAu catalysts suppress the bicarbonate-mediated hydrogen evolution reaction (HER) compared to a flat Au electrode. Additionally, the geometric current density for CO2RR increases with the roughness of NpAu catalysts, which we attribute to the increased availability of active sites at NpAu catalysts. Together, the enhancement of CO2RR and the suppression of competing HER results in a drastic increase in the faradaic selectivity for CO2RR with increasing pore length and decreasing pore diameter, reaching near 100% faradaic efficiency for CO in the most extreme case. Interestingly, unlike the geometric current density, the specific current density for CO2RR has a more complicated relation with the roughness of the NpAu catalysts. We show that this is due to the presence of ohmic drop effects along the length of the porous channels. These ohmic drop effects render the pores partially electrocatalytically inactive and hence, they play an important role in tuning the CO2RR activity on nanoporous catalysts.
ABSTRACT
Selective oxidation of higher alcohols using heterogeneous catalysts is an important reaction in the synthesis of fine chemicals with added value. Though the process for primary alcohol oxidation is industrially established, there is still a lack of fundamental understanding considering the complexity of the catalysts and their dynamics under reaction conditions, especially when higher alcohols and liquid-phase reaction media are involved. Additionally, new materials should be developed offering higher activity, selectivity, and stability. This can be achieved by unraveling the structure-performance correlations of these catalysts under reaction conditions. In this regard, researchers are encouraged to develop more advanced characterization techniques to address the complex interplay between the solid surface, the dissolved reactants, and the solvent. In this mini-review, we report some of the most important approaches taken in the field and give a perspective on how to tackle the complex challenges for different approaches in alcohol oxidation while providing insight into the remaining challenges.
ABSTRACT
In this article, we investigate the poisoning reaction that occurs at platinum electrodes during the electrocatalytic hydrogenation of acetone. A better understanding of this poisoning reaction is important to develop electrocatalysts that are both active for the hydrogenation of carbonyl compounds and resilient against poisoning side reactions. We adsorb acetone to Pt(331), Pt(911), Pt(510), and Pt(533) (i.e., Pt[2(111) × (110)], Pt[5(100) × (111)], [5(100) × (110)], and Pt[4(111) × (100), respectively])) as well as Pt(100) single-crystal electrodes and perform reductive and oxidative stripping experiments after electrolyte exchange. We found that acetone adsorbs molecularly intact on all sites apart from Pt(100) terrace sites and can be stripped reductively from the electrode surface at a potential positive of hydrogen evolution. However, at Pt(100) terraces, acetone adsorbs dissociatively as carbon monoxide, which remains attached to the electrode surface and leads to its poisoning. Strikingly, dissociative adsorption does not occur on step sites with (100) geometry, which suggests that the dissociative adsorption of acetone is limited to Pt(100) terraces featuring a certain minimum "ensemble" number of freely available Pt atoms.
ABSTRACT
In this article we investigate the electrochemical reduction of CO2 at gold electrodes under mildly acidic conditions. Differential electrochemical mass spectroscopy (DEMS) is used to quantify the amounts of formed hydrogen and carbon monoxide as well as the consumed amount of CO2. We investigate how the Faradaic efficiency of CO formation is affected by the CO2 partial pressure (0.1-0.5 bar) and the proton concentration (1-0.25 mM). Increasing the former enhances the rate of CO2 reduction and suppresses hydrogen evolution from proton reduction, leading to Faradaic efficiencies close to 100%. Hydrogen evolution is suppressed by CO2 reduction as all protons at the electrode surfaces are used to support the formation of water (CO2 + 2H+ + 2e- â CO + H2O). Under conditions of slow mass transport, this leaves no protons to support hydrogen evolution. On the basis of our results, we derive a general design principle for acid CO2 electrolyzers to suppress hydrogen evolution from proton reduction: the rate of CO/OH- formation must be high enough to match/compensate the mass transfer of protons to the electrode surface.
ABSTRACT
Electrode surfaces may change their surface structure as a result of the adsorption of chemical species, impacting their catalytic activity. Using density functional theory, we find that the strong adsorption of hydrogen at low electrode potentials promotes the thermodynamics and kinetics of a unique type of roughening of 110-type Pt step edges. This change in surface structure causes the appearance of the so-called "third hydrogen peak" in voltammograms measured on Pt electrodes, an observation that has eluded explanation for over 50 years. Understanding this roughening process is important for structure-sensitive (electro)catalysis and the development of active and stable catalysts.
ABSTRACT
This paper studies the electrochemical hydrogenation of the carbonyl functional group of acetophenone and 4-acetylpyridine at platinum single-crystal electrodes. Comparison with results obtained for the hydrogenation of acetone featuring an isolated carbonyl functional group reveals the influence of the phenyl ring and the pyridine ring, respectively. Lack of acetone adsorption at Pt(111) and Pt(100) due to a weak interaction between surface and carbonyl functional group renders these surfaces inactive for the hydrogenation of acetone. Adsorption through a strong interaction with the phenyl ring of acetophenone activates the Pt(111) and Pt(100) surfaces for hydrogenation of the acetyl substituent. In agreement with previous results for acetone reduction, the Pt(100) surface is specifically active for the hydrogenolysis reaction, breaking the C-O bond, whereas the other surfaces only hydrogenate the carbonyl functionality. In contrast to the phenyl ring, the pyridine ring has a very different effect: due to the dominant interaction of the N atom of the pyridine ring with the platinum electrode, a vertical adsorption mode is realized. The resulting large physical distance between the carbonyl functional group and the electrode surface inhibits the hydrogenation at all platinum surfaces. This also holds for the Pt(110) electrode, which is otherwise active for the electrochemical hydrogenation of the isolated carbonyl functional group of aliphatic ketones. Our results show how the combination of molecular structure of the reactant and surface structure of the catalyst determine the selective electroreduction of functionalized ketones.