PAHs in baby food: assessment of three different processing techniques for the preparation of reference materials.

A feasibility study for producing a matrix reference material for selected polycyclic aromatic hydrocarbons (PAHs) in baby food is reported. A commercially available baby food, containing carrots, potatoes, tomato, white beans and meat, was spiked with the so-called 15 + 1 PAHs included in the PAHs priority list for food of the EU, at a mass fraction level of 1 µg/kg. The contaminated baby food was further processed by autoclaving, freezing or freeze drying. The homogeneity of the three materials (bottle-to-bottle variation) and their short-term (4 weeks) and long-term (18 months) stability at different temperatures were assessed. To this end, an analytical method based on a solid-liquid extraction followed by cleaning up with gel permeation chromatography (GPC) and solid phase extraction (SPE) and GC-IDMS determination, was validated in-house. It could be demonstrated that the procedure fulfilled the demands for application to the homogeneity and isochronous stability studies for the candidate reference materials targeted here. All three materials proved to be sufficiently homogeneous for the intended use. Measurements on the autoclaved material provided the most promising results in terms of envisaged shelf life, although freeze drying was also found to be a suitable processing technique for most of the investigated PAHs. These results are an important step towards the development of a matrix reference material for PAHs in a processed food matrix in a presentation very similar to routine samples.

Nitrite in feed: from animal health to human health.

Nitrite is widely consumed from the diet by animals and humans. However the largest contribution to exposure results from the in vivo conversion of exogenously derived nitrate to nitrite. Because of its potential to cause to methaemoglobin (MetHb) formation at excessive levels of intake, nitrite is regulated in feed and water as an undesirable substance. Forages and contaminated water have been shown to contain high levels of nitrate and represent the largest contributor to nitrite exposure for food-producing animals. Interspecies differences in sensitivity to nitrite intoxication principally result from physiological and anatomical differences in nitrite handling. In the case of livestock both pigs and cattle are relatively susceptible. With pigs this is due to a combination of low levels of bacterial nitrite reductase and hence potential to reduce nitrite to ammonia as well as reduced capacity to detoxify MetHb back to haemoglobin (Hb) due to intrinsically low levels of MetHb reductase. In cattle the sensitivity is due to the potential for high dietary intake and high levels of rumen conversion of nitrate to nitrite, and an adaptable gut flora which at normal loadings shunts nitrite to ammonia for biosynthesis. However when this escape mechanism gets overloaded, nitrite builds up and can enter the blood stream resulting in methemoglobinemia. Looking at livestock case histories reported in the literature no-observed-effect levels of 3.3mg/kg body weight (b.w.) per day for nitrite in pigs and cattle were estimated and related to the total daily nitrite intake that would result from complete feed at the EU maximum permissible level. This resulted in margins of safety of 9-fold and 5-fold for pigs and cattle, respectively. Recognising that the bulkiness of animal feed limits their consumption, these margins in conjunction with good agricultural practise were considered satisfactory for the protection of livestock health. A human health risk assessment was also carried out taking into account all direct and indirect sources of nitrite from the human diet, including carry-over of nitrite in animal-based products such as milk, eggs and meat products. Human exposure was then compared with the acceptable daily intake (ADI) for nitrite of 0-0.07 mg/kg b.w. per day. Overall, the low levels of nitrite in fresh animal products represented only 2.9% of the total daily dietary exposure and thus were not considered to raise concerns for human health. It is concluded that the potential health risk to animals from the consumption of feed or to man from eating fresh animal products containing nitrite, is very low.

Human risk assessment of heavy metals: principles and applications.

Humans are exposed to a number of "heavy metals" such as cadmium, mercury and its organic form methylmercury, uranium, lead, and other metals as wel as metalloids, such as arsenic, in the environment, workplace, food, and water supply. Exposure to these metals may result in adverse health effects, and national and international health agencies have methodologies to set health-based guidance values with the aim to protect the human population. This chapter introduces the general principles of chemical risk assessment, the common four steps of chemical risk assessment: hazard identification, hazard characterization, exposure assessment, risk characterization, and toxicokinetic and toxicity aspects. Finally, the risk assessments performed by international health agencies such as the World Health Organisation, the Environmental Protection Agency of the United States, and the European Food Safety Authority are reviewed for cadmium, lead, mercury, uranium, and arsenic.

Optimisation of the GC-MS conditions for the determination of the 15 EU foodstuff priority polycyclic aromatic hydrocarbons.

European legislation has recently established a list of 15 priority polycyclic aromatic hydrocarbons (PAHs) to be monitored in foodstuff. Thus, the accurate determination of these compounds has become a highly relevant issue. The fact that some of these European Union (EU) PAHs differ from those typically analysed, requires the re-evaluation of the instrumental conditions for the proper determination of the new target compounds. In this study, the influence of the stationary phase and dimensions of the GC capillary column on the chromatographic resolution of the 15 EU PAHs has been investigated. Apolar (DB-5 type) and medium polar (DB-17 type) stationary phases with different lengths and film thickness have been evaluated for the separation of the target compounds, with special emphasis on those coelutions involving isomers such as the three benzofluoranthenes included in the EU PAHs. In addition, the influence of the injection technique and the column dimensions on the recovery of the high molecular mass PAHs has been studied. A programmable temperature vaporising (PTV) injector has been used in three different operational modes and the results were compared to those obtained using on-column injection. The experimental parameters involved in the injection step were optimised by using experimental design.

Occurrence of PCBs, PCDD/Fs, PBDEs and DDTs in Spanish breast milk: enantiomeric fraction of chiral PCBs.

Concentrations and congener specific profile of DDTs, PCBs and PCDD/Fs have been determined in a number of Spanish breast milk samples. The concentrations found indicate a decreasing tendency compared to previous data from the 1990s. Mean concentrations of 238 ng/g fat weight, 111 ng/g fat weight and 82.1 pg/g fat weight were found for DDTs, PCBs and 2,3,7,8-PCDD/Fs, respectively. When the WHO-TEQs were calculated, PCDD/Fs was the family contributing with the highest percentage to the total (62-84%), followed by the non-ortho PCBs (10-25%) and the mono-ortho PCBs (5-24%). The congener specific accumulation patterns found were comparable to those reported in other studies in industrialised countries. In addition, the levels of 9 PBDEs congeners have been also determined in the breast milk samples. The concentrations ranged from 0.04 to 1.38 ng/g fat weight. The enantiomeric enrichment of a number of chiral PCBs in the breast milk samples, including congeners 84, 91, 95, 132, 135, 149, 171, 174, 176 and 183, has also been studied, for some of them for the first time in this matrix.

Feasibility of two multidimensional techniques, heart-cut MDGC and GCxGC, for the separation of PCBs and PBDEs.

The feasibility of heart-cut MDGC-ECD and GCxGC-muECD for the separation of polybrominated diphenyl ethers (PBDEs) and polychlorinated biphenyls (PCBs) has been evaluated. Among the different column combinations tested, the best results were obtained when using either a DB-5 type or an HT-8 column as the first dimension combined with a mid-polar stationary phase (50% phenyl) as the second dimension. The co-elutions between the target PCBs and PBDEs in the first dimension were satisfactorily resolved once transferred to the second column. Repeatability and intermediate precision were satisfactory in both systems, considering retention times in both dimensions. Nevertheless, peak area/volume precision was better for heart-cut MDGC since software for the data analysis in the case of GCxGC was still under development. The need for multiple injections of the same extract on the heart-cut MDGC system was the main drawback since the analysis time it increased. GCxGC becomes then a valuable alternative able to achieve the same performance in one injection. However, the GCxGC data analysis is still very time-consuming and needs further development. The applicability of both separation techniques was shown using a human breast milk sample with low concentrations of PCBs (0.2-227 pg/g fresh weight) and PBDEs (1.2-41 pg/g fresh weight).

Determination of toxaphene enantiomers by comprehensive two-dimensional gas chromatography with electron-capture detection.

Comprehensive two-dimensional gas chromatography with micro electron-capture detection (GC x GC-microECD) has been evaluated for the enantioseparation of five chiral toxaphenes typically found in real-life samples (Parlar 26, 32, 40, 44 and 50). From the two enantioselective beta-cyclodextrin-based columns evaluated as first dimension column, BGB-176SE and BGB-172, the latter provided the best results and was further combined with three non-enantioselective columns in the second dimension: HT-8, BPX-50 and Supelcowax-10. The combination BGB-172 x BPX-50 was finally selected because it provided a complete separation among all enantiomers. A satisfactory repeatability and reproducibility of the retention times in both the first and the second dimension were observed for all target compounds (RSDs below 0.8%, n = 4). Linear responses in the tested range of 10-200 pg/microl and limits of detection in the range of 2-6 pg/microl were obtained. The repeatability and reproducibility at a concentration of 100 pg/microl, evaluated as the RSDs calculated for the enantiomeric fraction (EF), was better than 11% (n = 4) in all instances. The feasibility of the method developed for real-life analyses was illustrated by the determination of the enantiomeric ratios and concentration levels of the test compounds in four commercial fish oil samples. These results were compared to those obtained by heart-cut multidimensional gas chromatography using the same enantioselective column.

Quantitative analysis of polybrominated diphenyl ethers in adipose tissue, human serum and foodstuff samples by gas chromatography with ion trap tandem mass spectrometry and isotope dilution.

A method based on gas chromatography (GC) separation followed by ion trap tandem mass spectrometry detection in EI mode (ITD-MS/MS), using isotope dilution, was developed for the determination of ten native polybrominated diphenyl ethers (PBDEs) and four (13)C(12)-labeled congeners in biological (fat tissue and human serum) and food samples. The highest-mass fragment ions were used as precursor ions for those congeners with molecular ions with m/z values higher than the maximum of the instrument. In these cases (hepta-BDEs and (13)C(12)-hexa-BDEs) no fragmentation was achieved under the experimental conditions employed. Repeatability (lower than 9%) and reproducibility (lower than 13%), expressed as relative standard deviation (RSD, n = 3 and 4, respectively), were satisfactory. Similarly, the coefficient of variation (n = 4) of the isotopic ratio between the two most abundant product ions was lower than 10 and 6% for native and labeled congeners, respectively. To evaluate the feasibility of the method, the optimized isotope dilution GC/ITD-MS/MS method was used for the quantitation of selected PBDE congeners in different samples including adipose tissue, human serum and foodstuff samples, from three inter-laboratory comparative exercises, covering a wide range of concentrations. A solid-phase extraction procedure, previously developed for PCB determination in small-size bird serum samples, was successfully applied to quantification of PBDEs in 1 mL samples of human serum.

Evaluation of organochlorine compounds in peregrine falcon (Falco peregrinus) and their main prey (Columba livia) inhabiting central Spain.

The population of peregrine falcon (Falco peregrinus sbs. brookei) inhabiting the Regional Park of southeastern Madrid (RPSM), Spain, has experienced an increase of unsuccessful pairs (from 15% among a total of 20 pairs in 1995 to 55% among a total of 18 pairs in 2001). Traditionally, this area has been known to be contaminated with organochlorine compounds and toxic metals, which are known to be deleterious to the reproductive system of birds. During the breeding seasons of 2000 and 2001, contaminant residues were measured in unhatched eggs of peregrine falcons and liver of their main prey, to determine if they could be affecting the survival of the population. The most abundant contaminants were ortho-polychlorinated biphenyls (ortho-PCBs), ranging from 202.56 to 3,335.16 ng/g (wet wt) in falcon eggs and from 10.25 to 53.51 ng/g (wet wt) in pigeon livers. In all samples, the 2,3,7,8-substituted polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) were detected, although these levels never exceeded 20 pg/g (wet wt). The major contributor to total toxic equivalent quantities (TEQs) were non-ortho-PCBs. Organochlorine levels found in this study may contribute to the entire suite of stressors that are negatively affecting the peregrine population.

Chiral comprehensive two-dimensional gas chromatography with electron-capture detection applied to the analysis of chiral polychlorinated biphenyls in food samples.

The feasibility of comprehensive two-dimensional gas chromatography with electron-capture detection (GC x GC-ECD) for the enantioseparation of chiral PCBs from other possible interfering compounds has been evaluated. Three commercially available enantioselective beta-cyclodextrin-based capillary columns (Chirasil-Dex, BGB-172 and BGB-176SE) have been tested as first-dimension columns. Three non-enantioselective stationary phases (HT-8, BPX-50 and Supelcowax-10) were combined with the enantioselective columns to allow the unambiguous determination of the enantiomers of the target chiral PCBs. Each enantioselective first-dimension column tested was able to separate into enantiomers different PCB congeners, but in all cases, the use of Supelcowax-10 as second-dimension column provided the most satisfactory results. The Chirasil-Dex x Supelcowax-10 column combination allowed the determination of the enantiomeric fraction (EF) of PCBs 84, 91, 95, 132, 136, 149, 174 and 176 in the working standard solution, while that of congener 135 was hindered. The BGB-172 x Supelcowax-10 column set allowed a proper EF determination of congeners 45, 84, 131, 132, 135, 171, 174 and 183, while that of PCB 91 was interfered with co-elutants. The column combination BGB-176SE x Supelcowax-10 allowed the determination of all congeners that this enantioselective stationary phase was able to separate into enantiomers, i.e. PCBs 45, 91, 95, 136, 149 and 176. These column combinations have also been evaluated for the simultaneous determination of the 12 congeners with a toxic equivalency factor assigned by the WHO (PCBs 77, 81, 105, 114, 118, 123, 126, 156, 157, 167, 169, 189) and the seven indicator congeners (PCBs 28, 52, 101, 118, 138, 153 and 180), and evaluated for the analysis of food samples.

EROD induction and PCDD/F levels in fish liver from the Biobio River in Chile.

The Biobio River basin, located in central Chile, is one of the most important freshwater resources for a population of 1 million inhabitants. The river receives discharges of pulp mills, sewage treatment plants and there is a diffuse input of materials coming from the drainage basin. Previous studies reported high levels of etoxyresorufin-O-deethylase (EROD) induction in fish from the lower stretch of the river, mainly due to polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) exposure. The present study investigates polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzo-furans (PCDFs) levels as well as EROD induction in fish livers from Central Chile's Biobio River. Dioxin and furan levels in fish livers are reported for the first time in three areas of the Basin. In all samples the highest concentrations were found for the octachlorodibenzo-p-dioxin (OCDD) and PCDD/F TEQ concentrations ranged from 2.83 to 6.33 ppt (wet weight). The results indicate a clear induction of EROD activity in different fish species as the river mouth is approached, although this induction is not clearly related with dioxin and furan levels found in the fish livers. Our results clearly show that other pollutants might be acting as EROD inductors in the Biobio Basin.

Enantiomeric separation of chiral polychlorinated biphenyls on beta-cyclodextrin capillary columns by means of heart-cut multidimensional gas chromatography and comprehensive two-dimensional gas chromatography. Application to food samples.

Three commercially available chiral capillary columns, Chirasil-Dex, BGB-176SE, and BGB-172, have been evaluated for the separation into enantiomers of the 19 chiral polychlorinated biphenyls (PCB) congeners stable at room temperature. The enantiomers of 15 chiral PCBs were, at least to some extent, separated using these beta-cyclodextrin based columns. Multidimensional techniques, such as heart-cut multi-dimensional gas chromatography (heart-cut MDGC) and comprehensive two-dimensional gas chromatography (GC x GC), were investigated for their ability to solve coelution problems with other PCBs present in commercial mixtures and real-life samples. Heart-cut MDGC improved the separation as compared to one-dimensional GC, and enantiomeric fractions of the investigated chiral PCBs could be determined free from interferences. However, limitations on the number of target compounds that can be transferred to the second column in a single run and, therefore, the time consumption, have led to the evaluation of GC x GC as an alternative for this type of analysis. With GC x GC, two column set-ups were tested, both having a chiral column as first-dimension column, and two different polar stationary phase columns in the second dimension. On using both column combinations, congeners 84, 91, 95, 132, 135, 136, 149, 174, and 176 could be determined free from coelutions with other PCBs. Results on the application of heart-cut MDGC to food samples such as milk and cheese are given, as well as the first results on the application of GC x GC to this type of samples.

Survey of persistent organochlorine contaminants (PCBs, PCDD/Fs, and PAHs), heavy metals (Cu, Cd, Zn, Pb, and Hg), and arsenic in food samples from Huelva (Spain): levels and health implications.

Concentrations of PCBs, PCDDs, and PCDFs, heavy metals (Cu, Cd, Zn, Pb, and Hg), and arsenic have been determined in a great variety of food samples purchased in different markets across the city of Huelva, located in southwestern Spain and under strong industrial activity. All samples analyzed presented concentrations below the maximum allowed by the European Community regarding PCDD/Fs, with the exception of samples within the meat group. An estimation of the daily intake resulted in 1.15 pg of WHO(PCDD/Fs)-TEQ/kg of body weight/day for a 70 kg person and 2.63 pg of WHO-TEQ/kg of body weight/day when PCBs were included, therefore accounting for a similar or even higher percentage than PCDD/Fs and showing the importance of their inclusion in monitoring studies. Meat and meat products, together with vegetable oils and dairy products, were the major food groups contributing to the estimated daily intake. For heavy metals and arsenic, the concentrations found were under the value proposed by European regulations, and estimated daily intakes were well below those proposed by the WHO for all metals investigated. PAHs have been analyzed in food samples from marine origin, values ranging from 8.22 to 71.4 ng/g of fresh weight. Pyrene was the most abundant compound, accounting for >80% in the samples investigated. The most carcinogenic PAHs, such as benzo[a]pyrene and dibenz[a,h]anthracene, were in all cases below the limits of detection. Therefore, the samples analyzed in this survey can be considered as safe with regard to the levels obtained and the in-force legislation.