Comparison of L1 and L5 Bands GNSS Signals Acquisition.

Nowadays, civil Global Navigation Satellite System (GNSS) signals are available in both L1 and L5 bands. A receiver does not need to acquire independently the signals in both bands coming from a same satellite, since their carrier Doppler and code delay are closely related. Therefore, the question of which one to acquire first rises naturally. Although the common thought would tell the L1 band signals which are narrowband, an accurate comparison has never been done, and the decision is not as easy as it seems. Indeed, L5 band signals have several advantages such as stronger power, lower carrier Doppler, or a pilot channel, unlike the Global Positioning System (GPS) L1 C/A signal. The goal of this paper is therefore to compare the acquisition of L1 and L5 bands signals (GPS L1 C/A and L5, Galileo E1 and E5a/b) to determine which one is more complex and by which factor, in terms of processing time and memory, considering hardware receivers and the parallel code search. The results show that overall the L5 band signals are more complex to acquire, but it depends strongly on the conditions. The E5 signal is always more complex to acquire than E1, while the L5 signal can have a complexity close to the L1 C/A in some cases. Moreover, precise assistance providing accurate Doppler could significantly reduce the L5 complexity below the L1 complexity.

Derivation of the Cramér-Rao Bound in the GNSS-Reflectometry Context for Static, Ground-Based Receivers in Scenarios with Coherent Reflection.

The use of the reflected Global Navigation Satellite Systems' (GNSS) signals in Earth observation applications, referred to as GNSS reflectometry (GNSS-R), has been already studied for more than two decades. However, the estimation precision that can be achieved by GNSS-R sensors in some particular scenarios is still not fully understood yet. In an effort to partially fill this gap, in this paper, we compute the Cramér-Rao bound (CRB) for the specific case of static ground-based GNSS-R receivers and scenarios where the coherent component of the reflected signal is dominant. We compute the CRB for GNSS signals with different modulations, GPS L1 C/A and GPS L5 I/Q, which use binary phase-shift keying, and Galileo E1 B/C and E5, using the binary offset carrier. The CRB for these signals is evaluated as a function of the receiver bandwidth and different scenario parameters, such as the height of the receiver or the properties of the reflection surface. The CRB computation presented considers observation times of up to several tens of seconds, in which the satellite elevation angle observed changes significantly. Finally, the results obtained show the theoretical benefit of using modern GNSS signals with GNSS-R techniques using long observation times, such as the interference pattern technique.

Standalone GPS L1 C/A Receiver for Lunar Missions.

Global Navigation Satellite Systems (GNSSs) were originally introduced to provide positioning and timing services for terrestrial Earth users. However, space users increasingly rely on GNSS for spacecraft navigation and other science applications at several different altitudes from the Earth surface, in Low Earth Orbit (LEO), Medium Earth Orbit (MEO), Geostationary Earth Orbit (GEO), and feasibility studies have proved that GNSS signals can even be tracked at Moon altitude. Despite this, space remains a challenging operational environment, particularly on the way from the Earth to the Moon, characterized by weaker signals with wider gain variability, larger dynamic ranges resulting in higher Doppler and Doppler rates and critically low satellite signal availability. Following our previous studies, this paper describes the proof of concept "WeakHEO" receiver; a GPS L1 C/A receiver we developed in our laboratory specifically for lunar missions. The paper also assesses the performance of the receiver in two representative portions of an Earth Moon Transfer Orbit (MTO). The receiver was connected to our GNSS Spirent simulator in order to collect real-time hardware-in-the-loop observations, and then processed by the navigation module. This demonstrates the feasibility, using current technology, of effectively exploiting GNSS signals for navigation in a MTO.

Normalized GNSS interference pattern technique for altimetry.

It is well known that reflected signals from Global Navigation Satellite Systems (GNSS) can be used for altimetry applications, such as monitoring of water levels and determining snow height. Due to the interference of these reflected signals and the motion of satellites in space, the signal-to-noise ratio (SNR) measured at the receiver slowly oscillates. The oscillation rate is proportional to the change in the propagation path difference between the direct and reflected signals, which depends on the satellite elevation angle. Assuming a known receiver position, it is possible to compute the distance between the antenna and the surface of reflection from the measured oscillation rate. This technique is usually known as the interference pattern technique (IPT). In this paper, we propose to normalize the measurements in order to derive an alternative model of the SNR variations. From this model, we define a maximum likelihood estimate of the antenna height that reduces the estimation time to a fraction of one period of the SNR variation. We also derive the Cramér-Rao lower bound for the IPT and use it to assess the sensitivity of different parameters to the estimation of the antenna height. Finally, we propose an experimental framework, and we use it to assess our approach with real GPS L1 C/A signals.

Implementation and performance of a GPS/INS tightly coupled assisted PLL architecture using MEMS inertial sensors.

The use of global navigation satellite system receivers for navigation still presents many challenges in urban canyon and indoor environments, where satellite availability is typically reduced and received signals are attenuated. To improve the navigation performance in such environments, several enhancement methods can be implemented. For instance, external aid provided through coupling with other sensors has proven to contribute substantially to enhancing navigation performance and robustness. Within this context, coupling a very simple GPS receiver with an Inertial Navigation System (INS) based on low-cost micro-electro-mechanical systems (MEMS) inertial sensors is considered in this paper. In particular, we propose a GPS/INS Tightly Coupled Assisted PLL (TCAPLL) architecture, and present most of the associated challenges that need to be addressed when dealing with very-low-performance MEMS inertial sensors. In addition, we propose a data monitoring system in charge of checking the quality of the measurement flow in the architecture. The implementation of the TCAPLL is discussed in detail, and its performance under different scenarios is assessed. Finally, the architecture is evaluated through a test campaign using a vehicle that is driven in urban environments, with the purpose of highlighting the pros and cons of combining MEMS inertial sensors with GPS over GPS alone.