Temporal and spatial distribution of microplastics in green infrastructures: Rain gardens.

Rain gardens, a type of green infrastructure (GI), have been recognized for mitigating flooding and improving water quality from minor storms by trapping stormwater pollutants. Yet, the capability of these systems to retain microplastics (MPs) from stormwater, especially in size <125 µm, remains inadequately understood. This study investigated the spatial and temporal distributions of MPs in three rain gardens located in Newark, New Jersey, USA. The rain gardens have been in operation for ∼7 years and located in different land uses: low-density residential (Site 1), commercial (Site 2), and high-density residential (Site 3). The sediment samples were collected during May 2022, August 2022, and February 2023 at various soil depths and horizontal distances of rain gardens. The MPs were quantified and characterized using Fourier transform infrared (FTIR) spectrometer and a Raman microscope. The overall mean concentration varied between sampling sites, with 469 ± 89.8 pkg-1 in Site 1, 604 ± 91.4 pkg-1 in Site 2, and 997 ± 64.3 pkg-1 in Site 3, with Polypropylene as the dominant polymer, followed by nylon and polyethylene. In the vertical direction, larger MPs (250 µm-5 mm) were effectively retained within the top 5 cm and their concentration declined exponentially with the increasing depths. Small-sized MPs (1-250 µm) were prevalent at deeper depths (≥ 10 cm), and no MPs were found below 15 cm. In the horizontal direction, the highest MP concentration was observed near the stormwater inlet, and the concentration decreased away from the inlet. Over the nine-month period, a notable increase in concentration was observed at all sites. These findings contribute valuable knowledge towards developing effective measures for retaining MPs from stormwater and monitoring GIs in urban environments.

Mobilization of per- and poly-fluoroalkyl substances (PFAS) in soils with different organic matter contents.

There is considerable interest in addressing soils contaminated with per- and polyfluoroalkyl substances (PFAS) because of the PFAS in the environment and associated health risks. The neutralization of PFAS in situ is challenging. Consequently, mobilizing the PFAS from the contaminated soils into an aqueous solution for subsequent handling has been pursued. Nonetheless, the efficiency of mobilization methods for removing PFAS can vary depending on site-specific factors, including the types and concentrations of PFAS compounds, soil characteristics. In the present study, the removal of perfluorooctanoate (PFOA) and perfluorooctane sulfonate (PFOS) from artificially contaminated soils was investigated in a 2D laboratory setup using electrokinetic (EK) remediation and hydraulic flushing by applying a hydraulic gradient (HG) for a duration of 15 days. The percent removal of PFOA by EK was consistent (∼80%) after a 15-day treatment for all soils. The removal efficiency of PFOS by EK significantly varied with the OM content, where the PFOS removal increased from 14% at 5% OM to 60% at 50% OM. With HG, the percent removal increased for both PFOA and PFOS from about 20% at 5% OM up to 80% at 75% OM. Based on the results, the mobilization of PFAS from organic soil would be appropriate using both hydraulic flushing and EK considering their applicability and advantages over each other for site-specific factors and requirements.

Repurposing spent biomass of vetiver grass used for stormwater treatment to generate biochar and ethanol.

Stormwater pollution is a key factor contributing to water quality degradation, posing substantial environmental and human health risks. Although stormwater retention ponds, also referred to as wet ponds, are commonly implemented to alleviate stormwater challenges by reducing peak flow and removing suspended solids, their effectiveness in removing heavy metals and nutrients is limited. This study evaluated the performance of floating treatment platforms (FTPs) featuring vetiver grass (Chrysopogon zizanioides), a non-invasive, nutrient- and metal-accumulating perennial grass, in removing heavy metals (Cu, Pb, and Zn) and nutrients (P and N) in stormwater retention ponds. Furthermore, the potential for utilizing the spent vetiver biomass for generating biochar and bioethanol was investigated. The study was conducted in a greenhouse setup under simulated wet and dry weather conditions using pond water collected from a retention pond in Stafford Township, New Jersey, USA. Two FTPs with vetiver (vegetated FTPs) were compared with two FTPs without vetiver (non-vegetated FTPs), which served as controls. Results showed that the removal of heavy metals and nutrients by the FTPs with vetiver was significantly higher (p < 0.05) than the FTPs without vetiver. Notably, vetiver showed resilience to stormwater pollutants and hydroponic conditions, displaying no visible stress symptoms. The biochar and bioethanol generated from the spent vetiver exhibited desirable yield and quality, without raising concerns regarding pollutant leaching, indicated by very low TCLP and SPLP concentrations. This study provides compelling evidence that the implementation of vetiver-based FTPs offers a cost-effective and environment-friendly solution for mitigating stormwater pollution in retention ponds. Furthermore, the utilization of vetiver biomass for biofuel and biochar production supports clean production and fostering circular economy efforts.

Weather and the City: Machine Learning for Predicting and Attributing Fine Scale Air Quality to Meteorological and Urban Determinants.

Urban air quality persists as a global concern, with critical health implications. This study employs a combination of machine learning (gradient boosting regression, GBR) and spatial analysis to better understand the key drivers behind air pollution and its prediction and mitigation strategies. Focusing on New York City as a representative urban area, we investigate the interplay between urban characteristics and weather factors, showing that urban features, including traffic-related parameters and urban morphology, emerge as crucial predictors for pollutants closely associated with vehicular emissions, such as elemental carbon (EC) and nitrogen oxides (NOx). Conversely, pollutants with secondary formation pathways (e.g., PM2.5) or stemming from nontraffic sources (e.g., sulfur dioxide, SO2) are predominantly influenced by meteorological conditions, particularly wind speed and maximum daily temperature. Urban characteristics are shown to act over spatial scales of 500 × 500 m2, which is thus the footprint needed to effectively capture the impact of urban form, fabric, and function. Our spatial predictive model, needing only meteorological and urban inputs, achieves promising results with mean absolute errors ranging from 8 to 32% when using full-year data. Our approach also yields good performance when applied to the temporal mapping of spatial pollutant variability. Our findings highlight the interacting roles of urban characteristics and weather conditions and can inform urban planning, design, and policy.

Modeling impacts of river hydrodynamics on fate and transport of microplastics in riverine environments.

Microplastics pose a significant and growing threat to marine ecosystems and human health. Rivers serve as critical pathways for the entry of inland-produced microplastics into marine environments. In this paper, we developed a numerical modeling scheme using OpenFOAM to investigate the fate and transport of microplastics in a river system. Our simulation results show that microplastics undergo significant aggregation and breakage as they are transported downstream by river flows. This significantly alters the particle size distribution of microplastics. The aggregation-breakage process is mainly controlled by river hydrodynamics and pollution scale. Our findings suggest that a significant extent of particle aggregation occurs at an early stage of the release of microplastics in the river, while the aggregation-breakage process becomes limited as the microplastic plume is gradually dispersed and diluted downstream. Eddy diffusivity drives the dispersion of the microplastic plume in the river, and its spatial patterns affect the aggregation-breakage process.

Characterizing microplastics in urban runoff: A multi-land use assessment with a focus on 1-125 µm size particles.

Urban areas play a significant role in generating microplastics (MPs) through increased vehicular and human activities, making urban runoff a key source of MP pollution in receiving waterways. The composition of MPs is anticipated to vary with land use; hence, identifying the hotspots of contamination within urban areas is imperative for the targeted interventions to reduce MPs at their sources. This study collected one-liter stormwater runoffs from three different land uses as sheet flow during two storm events to quantify the MPs and identify the polymers transported from land-based sources. The analytical method included a combination of Fourier transform infrared spectrometer, Raman microscope, and Nile red staining techniques. This study analyzed the broad spectrum of MPs, i.e., 1 µm-5 mm, and tire wear and bitumen particles, considered the two major research gaps in stormwater studies. The MP concentrations were 67.7 ± 11.3 pL-1in commercial, 23 ± 10.3 pL-1 in residential, and 168.7 ± 37.1 pL-1in highways. The trend of MP concentrations followed an order of highway > commercial > residential with an exclusive presence of polymethylmethacrylate and ethylene-vinyl acetate in highways; cellophane, methylcellulose, polystyrene, polyamide, and polytetrafluorethylene in commercial; and high-density polyethylene in residential areas. The dominant MP morphology consisted of fragments, accounting for 89 % of the identified MPs, followed by 10 % fibers and 1 % films. This study observed a prevalence of MPs sizes <125 µm constituting 49 % of the total composition. These findings underscore the vital role of land use patterns in shaping MP abundance and reinforce the urgency of implementing effective management strategies to mitigate MP pollution in stormwater runoff.

A generic approach to construct pseudo components for oil weathering models.

Oil weathering models are essential for predicting the behavior of spilled oil in the environment. Most models use a "Pseudo Component" (PC) approach to represent the wide range of compounds found in petroleum products. Within the approach, rather than modeling each individual compound in an oil, a manageable number of PCs are developed that represent whole classes of compounds. However, previous studies focused mainly on traditional crude oils and did not develop a generic approach to create an optimal set of PCs for a variety of oils. In developing the updates to the NOAA oil weathering model, we propose herein a generic approach to construct PCs using oil distillation data to capture the complexity of oil evaporative weathering. We validated our approach with 899 oils from the Automated Data Inquiry for Oil Spills (ADIOS) oil library and found that an optimal set of sixteen PCs should be used. These PCs include two with low boiling point (below 144 °C), one with a high boiling point (above 400 °C), and thirteen constructed within a middle range of boiling points with a temperature resolution of 20 °C. Our simulation tests suggested that this set of sixteen PCs adequately characterizes oil evaporation processes for a wide variety of oils.

Field fluorometers for assessing oil dispersion at sea.

Oil dispersion by the application of chemical dispersants is an important tool in oil spill response, but it is difficult to quantify in the field in a timely fashion that is useful for coordinators and decision-makers. One option is the use of rugged portable field fluorometers that can deliver essentially instantaneous results if access is attainable. The United States Coast Guard has suggested, in their Special Monitoring of Applied Response Technologies (SMART) protocols, that successful oil dispersion can be identified by a five-fold increase in oil fluorescence. Here we test three commercial fluorometers with different excitation/emission windows (SeaOWL, Cyclops 7FO, and Cyclops 7F-G) that might prove useful for such applications. Results show that they have significantly different dynamic ranges for detecting oil and that using them (or similar instruments) in combination is probably the best option for successfully assessing the effectiveness of oil dispersion operations. Nevertheless, the rapid dilution of dispersed oil means that measurements must be made within an hour or two of dispersion, suggesting that one feasible scenario would be monitoring ship-applied dispersants by vessels following close behind the dispersant application vessel. Alternatively, autonomous submersibles might be pre-deployed to monitor aerial dispersant application, although the logistical challenges in a real spill would be substantial.

Green engineered mulch for phosphorus and metal removal from stormwater runoff in bioretention systems.

Phosphorus and metals in stormwater runoff are major causes of water quality degradation. Bioretention systems are increasingly implemented to improve stormwater quality and to better manage stormwater quantity. Many studies have focused on modifying the composition of the soil bed to improve pollutant removal. However, the pollutant removal performance of bioretention systems can diminish over time, such as when clogging of the media occurs. Sediment accumulation on the soil surface may inhibit infiltration into the soil bed, thus limiting pollutant removal. Soil replacement may be eventually required as pollutants accumulate in the soil. In this study, a green retrofit material, called green engineered mulch (GEM), was generated by coating regular wood mulch with aluminum-based water treatment residuals (WTR) via a simple and low-energy process (patent pending). The GEM was developed to serve as a green retrofit for bioretention systems to enhance the removal of phosphorus and metals from stormwater runoff. The GEM was placed in a rain garden in Secaucus, NJ, USA for 15 months, during which 12 storm events (ranging from 6.0 mm to 89.6 mm) were monitored. Runoff and infiltrate samples were analyzed for dissolved and total concentrations of phosphorus and metals, along with other key water quality parameters. The GEM significantly reduced (p < 0.05) the total concentrations of phosphorus and metals in stormwater infiltrate compared to the inlet, unlike the regular mulch. Minimal or no contact with the GEM resulted in no significant pollutant removal from surface runoff. No significant pollutant export from the GEM was observed. The spent GEM can be disposed of as non-hazardous waste in municipal landfills. This study demonstrates that the GEM is a safe and effective retrofit. Moreover, the GEM is a simple and economical retrofit solution that can be used in place of regular mulch in bioretention systems.

Recommendations for advancing media preparation methods used to assess aquatic hazards of oils and spill response agents.

Laboratory preparation of aqueous test media is a critical step in developing toxicity information needed for oil spill response decision-making. Multiple methods have been used to prepare physically and chemically dispersed oils which influence test outcome, interpretation, and utility for hazard assessment and modeling. This paper aims to review media preparation strategies, highlight advantages and limitations, provide recommendations for improvement, and promote the standardization of methods to better inform assessment and modeling. A benefit of media preparation methods for oil that rely on low to moderate mixing energy coupled with a variable dilution design is that the dissolved oil composition of the water accommodation fraction (WAF) stock is consistent across diluted treatments.  Further, analyses that support exposure confirmation maybe reduced and reflect dissolved oil exposures that are bioavailable and amenable to toxicity modeling.  Variable loading tests provide a range of dissolved oil compositions that require analytical verification at each oil loading. Regardless of test design, a preliminary study is recommended to optimize WAF mixing and settling times to achieve equilibrium between oil and test media. Variable dilution tests involving chemical dispersants (CEWAF) or high energy mixing (HEWAF) can increase dissolved oil exposures in treatment dilutions due to droplet dissolution when compared to WAFs. In contrast, HEWAF/CEWAFs generated using variable oil loadings are expected to provide dissolved oil exposures more comparable to WAFs. Preparation methods that provide droplet oil exposures should be environmentally relevant and informed by oil droplet concentrations, compositions, sizes, and exposure durations characteristic of field spill scenarios. Oil droplet generators and passive dosing techniques offer advantages for delivering controlled constant or dynamic dissolved exposures and larger volumes of test media for toxicity testing. Adoption of proposed guidance for improving media preparation methods will provide greater comparability and utility of toxicity testing in oil spill response and assessment.

Modeling the Breakup of Oil-Particle Aggregates in Turbulent Environments for Projectile Penetration.

After an oil spill incident, the spilled oil slicks are observed to migrate to the shoreline area. Under the turbulent conditions, they break into small droplets and are suspended in the water column. The dispersed droplets are expected to interact with the suspended particles and form the oil-particle aggregates (OPAs), which significantly changes the transport of the oil. Instead of an earlier assumption that particles cover the oil surface, thus preventing further breakage or aggregation of OPAs, recent studies demonstrated that particles act like projectiles penetrating the oil droplets, resulting in the breakage of OPAs over a longer period of time. A model looking into the OPA breakup through two breakup mechanisms was proposed for the first time. The first method depicted the breakup of one large OPA into two daughter droplets owing to the turbulent nature, while the second method demonstrated the tear of the OPA surface layer caused by particle uprooting. The model was then calibrated by an experimental study targeting crude oil with varied viscosities, along with previous experimental investigations. Three key factors were identified accounting for the breakage of OPAs, where the increase in particle concentration in the natural environment and the increase in turbulent energy of the surrounding flows benefited the breakage of OPAs, and the increase in oil viscosity suppressed the breakage due to large resistance to shear stress. Besides these elements, the impact of the particle shape on the penetration depth was discussed. The model serves as a fundamental theory to describe the evolution of OPAs for fragmentation behavior.

Post-Formation of Oil Particle Aggregates: Breakup and Biodegradation.

Spilled oil slicks are likely to break into droplets in the subtidal and intertidal zones of seashores due to wave energy. The nonliving suspended fine particles in coastal ecosystems can interact with the dispersed oil droplets, resulting in the formation of Oil Particle Aggregates (OPAs). Many investigations assumed that these aggregates will settle due to the particles' high density. Recent studies, however, reported that some particles penetrate the oil droplets, which results in further breakup while forming smaller OPAs that remain suspended in the water column. Here, we investigated the interaction of crude oil droplets with intertidal and subtidal sediments, as well as artificial pure kaolinite, in natural seawater. Results showed that the interaction between oil droplets and intertidal sediments was not particularly stable, with an Oil Trapping Efficiency (OTE) < 25%. When using subtidal sediments, OTE reached 56%. With artificial kaolinite, OPA formation and breakup were more significant (OTE reaching up to 67%) and occurred faster (within 12 h). Oil chemistry analysis showed that the biodegradation of oil in seawater (half-life of 485 h) was significantly enhanced with the addition of sediments, with half-lives of 305, 265, and 150 h when adding intertidal sediments, subtidal sediments, and pure kaolinite, respectively. Such results reveal how the sediments' shape and size affect the various oil-sediment interaction mechanisms, and the subsequent impact on the microbial degradation of petroleum hydrocarbons. Future studies should consider investigating the application of fine (several microns) and sharp (elongated-sheeted) sediments as a nondestructive and nontoxic technique for dispersing marine oil spills.

Effect of clay content on the mobilization efficiency of per- and polyfluoroalkyl substances (PFAS) from soils by electrokinetics and hydraulic flushing.

The need for the efficient remediation of soils impacted by per- and polyfluoroalkyl substances (PFAS) is substantially growing because of the notable upsurge in societal and regulatory awareness of this class of chemicals. To remediate PFAS-contaminated soils using mobilization approaches, the choice of appropriate techniques highly depends on the soil's composition, particularly the clay content, which significantly affects the soil's permeability. Here, we investigated the PFAS mobilization efficiency from soils with different clay contents by using two techniques: electrokinetic (EK) remediation and hydraulic flushing. Artificial kaolinite was added to a loamy sand soil to prepare four soil blends with clay contents of 5, 25, 50, and 75%, each contaminated with perfluorooctanoic acid (PFOA) and perfulorooctanesulfonic acid (PFOA) at 10,000 µg/kg. EK remediation was conducted by applying a low voltage (30 V) with a current of 100 mA, and hydraulic flushing was carried out by applying a hydraulic gradient (HG) with a slope of 6.7%. Results show that, with a 14-day treatment duration, the EK-mobilization efficiency was enhanced substantially with the increase of clay content (removal of PFOS increased from 20% at 5% clay to 80% at 75% clay), most likely due to the increase of electroosmotic flow due to the higher content of particles having a zeta potential (i.e., clay). For HG, increasing the clay content significantly suppressed the mobilization of PFAS (removal of PFOS decreased from 40% at 5% clay to 10% at 75% clay) due to a notable decrease in the soil's permeability. Based on the results, applying hydraulic flushing and washing techniques for mobilizing PFAS would be appropriate when treating permeable soils with a maximum clay content of about 25%; otherwise, other suitable mobilization techniques such as EKs should be considered.

Optimizing the maintenance strategies for a network of green infrastructure: An agent-based model for stormwater detention basins.

Various stormwater best management practices and green infrastructures (GIs) are recommended to address flooding, stormwater runoff, water quality, and sustainability. While detention basins are considered one of the main GI strategies, their benefits cannot be fully realized without properly maintaining them and making sure that they stay operational. Therefore, this paper used agent-based modeling (ABM) to devise an optimal maintenance program for detention basins to ensure that they function properly and continue to perform their water quality and flood control functions. More specifically, the following 2 agent types were incorporated in the model: 1) the detention basins were considered as static agents, and 2) the service teams responsible for the operation (maintenance, repair, and replacement) of the detention basins were considered as active agents. The developed ABM was applied for the entire network of stormwater detention basins in Newark, NJ. Sensitivity analysis was conducted to identify the most critical variables affecting the total cost of operating the network of detention basins as well as the functioning percentage of detention basins. In addition, optimization was implemented to determine the best maintenance program or policy that minimizes the total cost of operations, while also making sure that a desired functionality level or threshold is achieved for the entire network of detention basins. Finally, the ABM was statistically validated using a total of 10,000 Monte Carlo runs and 99% confidence intervals. The optimization results showed that, in order to minimize the total cost of maintaining the entire network of detention basins and ensure that at least 80% of the basins are in a functioning state at the end of the planning horizon, the decision-maker should implement the following maintenance program or strategy: have 2 service teams for the operations of the detention basins, follow a replacement policy, and replace detention basins after 3 maintenance periods. Also, the identified optimal maintenance program or strategy would result with an average total annual cost of around $4,085,000, where the average annual repair cost is around $2,572,200, the average annual maintenance cost is around $19,700, the average annual replacement cost is around $763,100, and the average annual service team cost is around $730,000. The proposed ABM for detention basins can be extended to other GIs as well as to different geographical areas. The usage of ABM has the advantage to reduce the subjectivity in developing plans for managing GIs.

Oil Transport Following the Deepwater Horizon Blowout.

The Deepwater Horizon oil spill in the Gulf of Mexico in 2010 was the largest in US history, covering more than 1,000 km of shorelines and causing losses that exceeded $50 billion. While oil transformation processes are understood at the laboratory scale, the extent of the Deepwater Horizon spill made it challenging to integrate these processes in the field. This review tracks the Deepwater Horizon oil during its journey from the Mississippi Canyon block 252 (MC252) wellhead, first discussing the formation of the oil and gas plume and the ensuing oil droplet size distribution, then focusing on the behavior of the oil on the water surface with and without waves. It then reports on massive drifter experiments in the Gulf of Mexico and the impact of the Mississippi River on the oil transport. Finally, it concludes by addressing the formation of oil-particle aggregates. Although physical processes lend themselves to numerical modeling, we attempted to elucidate them without using advanced modeling, as our goal is to enhance communication among scientists, engineers, and other entities interested in oil spills.

Relative sensitivity of hydrodynamic, thermodynamic, and chemical processes for simulating the buoyant multiphase plume and surfacing flows of an oil and gas blowout.

Deepwater hydrocarbon releases experience complex chemical and physical processes. To assess simplifications of these processes on model predictions, we present a sensitivity analysis using simulations for the Deepwater Horizon oil spill. We compare the buoyant multiphase plume metrics (trap height, rise time etc), the hydrocarbon mass flowrates at the near-field plume termination and their mass fractions dissolved in the water column and reaching the water surface. The baseline simulation utilizes a 19-component hydrocarbon model, live-fluid state equations, hydrate dynamics, and heat and mass transfer. Other simulations turn-off each of these processes, with the simplest one using inert oil and methane gas. Plume metrics are the least sensitive to the modeled processes and can be matched by adjusting the release buoyancy flux. The mass flowrate metrics are more sensitive. Both liquid- and gas-phase mass transfer should be modeled for accurate tracking of soluble components (e.g. C1 - C7 hydrocarbons) in the environment.

A perspective on quantifying resilience: Combining community and infrastructure capitals.

The resilience of communities has emerged as a major goal in policy and practice. Cities, states, and counties within the United States and around the world are passing laws requiring the incorporation of climate-related hazard vulnerability assessments within their master plan updates for resilience planning and design. The resilience of communities under present and future scenarios is thus becoming a cornerstone of decision making and actions. Decisions that would enhance resilience, however, span multiple sectors and involve various stakeholders. Quantifying community resilience is a key step in order to describe the preparedness level of communities, and subsequently locating non-resilient areas to further enhance their capacity to endure disasters. Two main approaches are currently being pursued to evaluate resilience. The first approach is the "community resilience" developed mainly by social scientists and planners, and it captures social resilience using numerous pre-disaster attributes to describe the functioning of a community. This approach subsumes that pre-disaster attributes can predict the community resilience to a disaster. The second approach is adopted for infrastructure resilience, mostly used by engineers, and it focuses on robustness, redundancy, resourcefulness, and rapidity. This approach is appropriate for systems that are operated by highly skilled personnel and where the actions are of engineering type. In this paper, we provide an overview of the two approaches, and we leverage their limitations to propose a hybrid approach that combines community and infrastructure capitals into an Area Resilience metric, called ARez. ARez captures the role/impact of both infrastructure and community and combines five sectors: energy, public health, natural ecosystem, socio-economic, and transportation. We present a proof-of-concept for the ARez metric, showing its practicality and applicability as a direct measure for resilience, over various time scales.

Aggregation of microplastics and clay particles in the nearshore environment: Characteristics, influencing factors, and implications.

Since nearly half of the world's population lives near the coast, coastal areas have become hotspots for microplastic (MP) pollution due to human activity. The ubiquity of natural colloids in coastal waters plays a critical role in the potential fate of, and risks posed by, MPs. Nevertheless, far less has been known regarding the aggregation of MPs with inorganic natural clay colloids, especially in the complicated nearshore environment. In this study, the aggregation behavior of MPs as well as the interaction between MPs and clay particles were investigated under different nearshore environmental conditions (MP-to-clay ratio, salinity gradient, humic acid concentration, and wave energy). The aggregation behavior was subjected by the repulsive energy barrier between particles and external energy transferred to the system. The low energy associated with mild wave conditions was favorable for the occurrence of aggregation, whereas sustained high energy under intense wave conditions was found to be detrimental to the aggregation behavior, and the aggregates were prone to fragmentation even if particles coalesced into large clusters. The analysis for the environmental fate of MPs demonstrated that the shoreline was likely to be the sink for most MPs ultimately.

Numerical simulation of multiphase oil behaviors in ice-covered nearshore water.

There has been an increase in marine transportation in cold regions, which in turn has led to an increasing risk of oil spills in these areas. To better support risk assessment and pollution control of oil spills, it is important to have a good understanding of oil transport in the environment. This information is essential to manage response priorities and help prepare contingency and mitigating measures. This study aims to simulate 3D wave propagation in shallow water with different broken-ice aerial coverage percentages to assess the fate and transport of oil spill in a nearshore area under different conditions. Based on the Reynolds-averaged Navier-Stokes momentum equations for an incompressible viscous fluid and the Volume of Fluid (VOF) method that is coupled with Six Degree of Freedom (6-DOF) model, a 3D numerical model of three-phase transient flow was developed. It was found that the presence of ice makes the spreading of spilled oil slower in the horizontal direction since the ice can build natural barriers to oil movement. The higher the ice concentration, the slower spilled oil migrates in all directions. The maximum oil volume fraction varies with increasing ice coverage on the water surface area. The wave frequency, the averaged flow velocity, and oil properties affect the oil spread extent and the oil volume fraction. The dumping effect of the wave due to the presence of ice makes the impact of this factor less critical than those in open water.

Development of an offshore response guidance tool for determining the impact of SSDI on released gas and benzene from artificial subsea oil well blowout simulations.

We present an analysis of 2225 simulations of artificial oil well blowouts in nearshore and offshore waters of Newfoundland, Canada. In the simulations, we coupled the VDROP-J and TAMOC models to simulate the fate and transport of oil and gas from the release to the sea surface. Simulations were conducted with and without subsea dispersant injection. We analyzed the simulation database to quantify the mass fraction of oil and gas that surfaces, the mass fraction of released benzene that surfaces, and the horizontal offset to the surfacing zone. These data are also synthesized to yield empirical correlations to predict these output metrics from key input parameters. These correlations are summarized in an excel spreadsheet that allows rapid evaluation of spill dynamics with minimal initial knowledge of spill details. We call this tool an offshore response guidance table, which allows exploration of spill dynamics under diverse spill and response options.