Implementing 1.5 mm internal diameter columns into analytical workflows.

The use of smaller column diameters in liquid chromatography (LC) is often associated with capillary LC. Although there are many analytical benefits gained by adapting this format, routine use continues to be challenging due to column fragility and extra column dispersion. Bridging the gap between routinely used 2.1 mm columns and capillary bore columns allows for a sequential but far from insignificant increase in performance without the need for specialized equipment associated with very low dispersion LC systems. Moreover, an incremental decrease in column internal diameter (i.d.) allows for similar mass load (avoiding column overload that may be observed in much larger decreases in i.d. without trapping) and thus an increase in measured signal. As such, 1.5 mm i.d. columns provide an alternative intermediate dimension between the more regularly used 2.1 mm i.d. columns and 1 mm i.d. columns. These columns balance an increase in sensitivity compared to 2.1 mm i.d. columns (theoretically doubling the time-domain peak area in mass sensitive detectors for the same mass load), while mitigating the efficiency losses due to extra-column dispersion effects that are commonly observed with 1.0 mm i.d. columns. Here, the use of 1.5 mm i.d. columns was applied to LC/UV analysis of small molecules and LC/MS methods for the analysis of monoclonal antibodies. With equivalent mass load on column, the 1.5 mm i.d. columns provide two-to-threefold improvement in analyte peak area signal for small molecules as well as intact, subunit, and peptide levels of antibody analysis. Peak height was also increased using the 1.5 mm i.d. column, although the scale of increase varies between isocratic and gradient modes, likely due to differences in system dispersion effects and variation in electrospray ionization efficiency at different flow rates.

Using 1.5 mm internal diameter columns for optimal compatibility with current liquid chromatographic systems.

This article describes the use of a new prototype column hardware made with 1.5 mm internal diameter (i.d.) and demonstrates some benefits over the 1.0 mm i.d. micro-bore column. The performance of 2.1, 1.5 and 1.0 mm i.d. columns were systematically compared. With the 1.5 mm i.d. column, the loss of apparent column efficiency can be significantly reduced compared to 1.0 mm i.d. columns in both isocratic and gradient elution modes. In the end, the 1.5 mm i.d. column is almost comparable to 2.1 mm i.d. column from a peak broadening point of view. The advantages of the 1.5 mm i.d. hardware vs 2.1 mm i.d. narrow-bore columns are the lower sample and solvent consumption, and reduced frictional heating effects due to decreased operating flow rates.

New wide-pore superficially porous stationary phases with low hydrophobicity applied for the analysis of monoclonal antibodies.

The article describes the development of new stationary phases for the analysis of proteins in reversed phase liquid chromatography (RPLC). The goal was to have columns offering high recovery at low temperature, low hydrophobicity and novel selectivity. For this purpose, three different ligands bound onto the surface of superficially porous silica-based particles were compared, including trimethyl-silane (C1), ethyl-dimethyl-silane (C2) and N-(trifluoroacetomidyl)-propyl-diisopropylsilane (ES-LH). These three phases were compared with two commercial RPLC phases. In terms of protein recovery, the new ES-LH stationary phase clearly outperforms the other phases for any type of biopharmaceutical sample, and can already be successfully used at a temperature of only 60°C. In terms of retention, the new ES-LH and C1 materials were the less retentive ones, requiring lower organic solvent in the mobile phase. However, it is important to mention that the stability of C1 phase was critical under acidic, high temperature conditions. Finally, some differences were observed in terms of selectivity, particularly for the ES-LH column. Besides the chemical nature of the stationary phase, it was found that the nature of organic modifier also plays a key role in selectivity.

Fundamental to achieving fast separations with high efficiency: A review of chromatography with superficially porous particles.

Types of particles have been fundamental to LC separation technology for many years. Originally, LC columns were packed with large-diameter (>100 µm) calcium carbonate, silica gel, or alumina particles that prohibited fast mobile-phase speeds because of the slow diffusion of sample molecules inside deep pores. During the birth of HPLC in the 1960s, superficially porous particles (SPP, ≥30 µm) were developed as the first high-speed stationary-phase support structures commercialized, which permitted faster mobile-phase flowrates due to the fast movement of sample molecules in/out of the thin shells. These initial SPPs were displaced by smaller totally porous particles (TPP) in the mid-1970s. But SPP history repeated when UHPLC emerged in the 2000s. Stationary-phase support structures made from sub-3-µm SPPs were introduced to chromatographers in 2006. The initial purpose of this modern SPP was to enable chromatographers to achieve fast separations with high efficiency using conventional HPLCs. Later, the introduction of sub-2-µm SPPs with UHPLC instruments pushed the separation speed and efficiency to a very fast zone. This review aims at providing readers a comprehensive and up-to-date view on the advantages of SPP materials over TPPs historically and theoretically from the material science angle.

Importance of Particle Pore Size in Determining Retention and Selectivity in Reversed Phase Liquid Chromatography.

Column selection often centers on the identification of a stationary phase that increases resolution for a certain class of compounds. While gains in resolution are most affected by selectivity of the stationary phase or modifications of the mobile phase, enhancements can still be made with an intentional selection of the packing material's microstructure. Unrestricted mass transfer into the particle's porous structure minimizes band broadening associated with hindered access to stationary phase. Increased efficiency, especially when operating above the optimal flow rates, can be gained if the pore size is significantly larger than the solvated analyte. Less studied are the effects of reduced access to pores due to physical hindrance and its impact on retention. This article explores the relationship between pore size and reversed phase retention, and specifically looks at a series of particle architectures with reversed phase and size exclusion modes to study retention associated with access to stationary phase surface area.

Rapid analysis of polycyclic aromatic hydrocarbons.

Polycyclic aromatic hydrocarbons are a continuing environmental and health concern. The analytical methods developed to analyze this class of compounds have relied on reversed phase liquid chromatography and are often on the order of tens of minutes. Reduction in analysis times through the application of sub-2 µm fully porous and superficially porous support materials can increase the throughput of these LC separations. Herein, we demonstrate similar selectivity between a fully porous 1.8 µm and a 2.7 µm superficially porous material. Separations were individually developed with in silico modeling for a given flow rate determined by the fully porous column's backpressure requirements. Since the 2.7 µm superficially porous materials inherently require less backpressure to achieve similar levels of efficiency as the 1.8 µm fully porous materials, a marked increase in throughput is possible with elevated flow rates. Good resolution for a standard 16-component sample mixture is demonstrated in a sub-minute separation.

Predicting the HILIC Retention Behavior of the N-Linked Glycopeptides Produced by Trypsin Digestion of Immunoglobulin Gs (IgGs).

The prediction of the retention behavior/time would facilitate the identification and characterization of glycoproteins, particularly the analytical challenges, such as the characterization of low-abundance glycoforms. This task is essential in the biotherapeutics industry, where the type and amount of glycosylation on recombinant IgG alter the efficacy, function, and immunogenicity. Models exist for the prediction of the hydrophilic interaction liquid chromatography retention of peptides and glycans. Here, we have devised a unified model to predict the retention behavior of glycopeptides from human IgGs and applied this to the analysis of glycopeptides from rabbit IgGs. The combined model is capable of accurately predicting the retention of native IgG glycopeptides on 2 completely different liquid chromatography-mass spectrometry systems.

Peptide retention prediction using hydrophilic interaction liquid chromatography coupled to mass spectrometry.

A model that predicts retention for peptides using a HALO® penta-HILIC column and gradient elution was created. Coefficients for each amino acid were derived using linear regression analysis and these coefficients can be summed to predict the retention of peptides. This model has a high correlation between experimental and predicted retention times (0.946), which is on par with previous RP and HILIC models. External validation of the model was performed using a set of H. pylori samples on the same LC-MS system used to create the model, and the deviation from actual to predicted times was low. Apart from amino acid composition, length and location of amino acid residues on a peptide were examined and two site-specific corrections for hydrophobic residues at the N-terminus as well as hydrophobic residues one spot over from the N-terminus were created.

Reversed-phase chromatography with large pore superficially porous particles for high throughput immunoglobulin G2 disulfide isoform separation.

Reversed-phase liquid chromatography (RPLC) has been commonly used in IgG2 disulfide isoforms analysis. Recently, the columns packed with large pore superficially porous particles (SPP) have become available commercially. This work explores the application of this SPP technology in IgG2 disulfide isoforms separation. A high throughput and improved resolution RPLC method is developed with the optimization of column selection, gradient, temperature and flow rate. Compared with the small particles RP-UHPLC columns, large pore SPP columns provide unique selectivity and several new peaks were resolved and identified to be the free thiol variants of the IgG2 disulfide isoforms. The optimized method enables the detailed characterization of cysteines related variants in a single and fast method.

Predicting the Retention Behavior of Specific O-Linked Glycopeptides.

O-Linked glycosylation is a common post-translational modification that can alter the overall structure, polarity, and function of proteins. Reverse-phase (RP) chromatography is the most common chromatographic approach to analyze O-glycosylated peptides and their unmodified counterparts, even though this approach often does not provide adequate separation of these two species. Hydrophilic interaction liquid chromatography (HILIC) can be a solution to this problem, as the polar glycan interacts with the polar stationary phase and potentially offers the ability to resolve the peptide from its modified form(s). In this paper, HILIC is used to separate peptides with O-N-acetylgalactosamine (O-GalNAc), O-N-acetylglucosamine (O-GlcNAc), and O-fucose additions from their native forms, and coefficients representing the extent of hydrophilicity were derived using linear regression analysis as a means to predict the retention times of peptides with these modifications.

Superficially porous particles with 1000Å pores for large biomolecule high performance liquid chromatography and polymer size exclusion chromatography.

To facilitate mass transport and column efficiency, solutes must have free access to particle pores to facilitate interactions with the stationary phase. To ensure this feature, particles should be used for HPLC separations which have pores sufficiently large to accommodate the solute without restricted diffusion. This paper describes the design and properties of superficially porous (also called Fused-Core®, core shell or porous shell) particles with very large (1000Å) pores specifically developed for separating very large biomolecules and polymers. Separations of DNA fragments, monoclonal antibodies, large proteins and large polystyrene standards are used to illustrate the utility of these particles for efficient, high-resolution applications.

The Separation and Quantitation of Peptides with and without Oxidation of Methionine and Deamidation of Asparagine Using Hydrophilic Interaction Liquid Chromatography with Mass Spectrometry (HILIC-MS).

Peptides with deamidated asparagine residues and oxidized methionine residues are often not resolved sufficiently to allow quantitation of their native and modified forms using reversed phase (RP) chromatography. The accurate quantitation of these modifications is vital in protein biotherapeutic analysis because they can affect a protein's function, activity, and stability. We demonstrate here that hydrophilic interaction liquid chromatography (HILIC) adequately and predictably separates peptides with these modifications from their native counterparts. Furthermore, coefficients describing the extent of the hydrophilicity of these modifications have been derived and were incorporated into a previously made peptide retention prediction model that is capable of predicting the retention times of peptides with and without these modifications. Graphical Abstract ᅟ.

Resolving Isomeric Glycopeptide Glycoforms with Hydrophilic Interaction Chromatography (HILIC).

The ability to resolve glycans while attached to tryptic peptides would greatly facilitate glycoproteomics, as this would enable site-specific glycan characterization. Peptide/glycopeptide separations are typically performed using reversed-phase liquid chromatography (RPLC), where retention is driven by hydrophobic interaction. As the hydrophilic glycans do not interact significantly with the RPLC stationary phase, it is difficult to resolve glycopeptides that differ only in their glycan structure, even when these differences are large. Alternatively, glycans interact extensively with the stationary phases used in hydrophilic interaction chromatography (HILIC), and consequently, differences in glycan structure have profound chromatographic shifts in this chromatographic mode. Here, we evaluate HILIC for the separation of isomeric glycopeptide mixtures that have the same peptide backbone but isomeric glycans. Hydrophilic functional groups on both the peptide and the glycan interact with the HILIC stationary phase, and thus, changes to either of these moieties can alter the chromatographic behavior of a glycopeptide. The interactive processes permit glycopeptides to be resolved from each other based on differences in their amino acid sequences and/or their attached glycans. The separations of glycans in HILIC are sufficient to permit resolution of isomeric N-glycan structures, such as sialylated N-glycan isomers differing in α2-3 and α2-6 linkages, while these glycans remain attached to peptides.

Reliable LC-MS quantitative glycomics using iGlycoMab stable isotope labeled glycans as internal standards.

Glycans have numerous functions in various biological processes and participate in the progress of diseases. Reliable quantitative glycomic profiling techniques could contribute to the understanding of the biological functions of glycans, and lead to the discovery of potential glycan biomarkers for diseases. Although LC-MS is a powerful analytical tool for quantitative glycomics, the variation of ionization efficiency and MS intensity bias are influencing quantitation reliability. Internal standards can be utilized for glycomic quantitation by MS-based methods to reduce variability. In this study, we used stable isotope labeled IgG2b monoclonal antibody, iGlycoMab, as an internal standard to reduce potential for errors and to reduce variabililty due to sample digestion, derivatization, and fluctuation of nanoESI efficiency in the LC-MS analysis of permethylated N-glycans released from model glycoproteins, human blood serum, and breast cancer cell line. We observed an unanticipated degradation of isotope labeled glycans, tracked a source of such degradation, and optimized a sample preparation protocol to minimize degradation of the internal standard glycans. All results indicated the effectiveness of using iGlycoMab to minimize errors originating from sample handling and instruments.

Are sub-2 µm particles best for separating small molecules? An alternative.

Superficially porous particles (SPP) in the 2.5-2.7 µm range provide almost the same efficiency and resolution of sub-2 µm totally porous particles (TPP), but at one-half to one-third of the operating pressure. The advantage of SPP has led to the introduction of sub-2 µm SPP as a natural extension of this technology. While short columns of both SPP and TPP sub-2 µm particles allow very fast separations, the efficiency advantages of these very small particles often are not realized nor sufficient to overcome some of the practical limitations and disadvantages of such small particles. Advantages and disadvantages of columns packed with sub-2 µm particles are described for comparison with the characteristics of larger particles. The authors conclude that while sub-2 µm particles have utility in research studies, columns of larger particles are often better suited for most applications. A suggested 2.0 µm superficially porous particle diameter retains many of the advantages of sub-2 µm particles, but minimizes some of the disadvantages. The characteristics of these new 2.0 µm SPP are described in studies comparing some present sub-2 µm SPP commercial columns for efficiency, column bed homogeneity and stability.

Liquid chromatography-selected reaction monitoring (LC-SRM) approach for the separation and quantitation of sialylated N-glycans linkage isomers.

The study of N-linked glycans is among the most challenging bioanalytical tasks because of their complexity and variety. The presence of glycoform families that differ only in branching and/or linkage position makes the identification and quantitation of individual glycans exceedingly difficult. Quantitation of these individual glycans is important because changes in the abundance of these isomers are often associated with significant biomedical events. For instance, previous studies have shown that the ratio of α2-3 to α2-6 linked sialic acid (SA) plays an important role in cancer biology. Consequently, quantitative methods to detect alterations in the ratios of glycans based on their SA linkages could serve as a diagnostic tool in oncology, yet traditional glycomic profiling cannot readily differentiate between these linkage isomers. Here, we present a liquid chromatography-selected reaction monitoring (LC-SRM) approach that we demonstrate is capable of quantitating the individual SA linkage isomers. The LC method is capable of separating sialylated N-glycan isomers differing in α2-3 and α2-6 linkages using a novel superficially porous particle (Fused-Core) Penta-HILIC (hydrophilic interaction liquid chromatography) column. SRM detection provides the relative quantitation of each SA linkage isomer, and minimizes interferences from coeluting glycans that are problematic for UV/Fluorescence based quantitation. With our approach, the relative quantitation of each SA linkage isomer is obtained from a straightforward liquid chromatography-mass spectrometry (LC-MS) experiment.

The use of ammonium formate as a mobile-phase modifier for LC-MS/MS analysis of tryptic digests.

A major challenge facing current mass spectrometry (MS)-based proteomics research is the large concentration range displayed in biological systems, which far exceeds the dynamic range of commonly available mass spectrometers. One approach to overcome this limitation is to improve online reversed-phase liquid chromatography (RP-LC) separation methodologies. LC mobile-phase modifiers are used to improve peak shape and increase sample load tolerance. Trifluoroacetic acid (TFA) is a commonly used mobile-phase modifier, as it produces peptide separations that are far superior to other additives. However, TFA leads to signal suppression when incorporated with electrospray ionization (ESI), and thus, other modifiers, such as formic acid (FA), are used for LC-MS applications. FA exhibits significantly less signal suppression, but is not as effective of a modifier as TFA. An alternative mobile-phase modifier is the combination of FA and ammonium formate (AF), which has been shown to improve peptide separations. The ESI-MS compatibility of this modifier has not been investigated, particularly for proteomic applications. This work compares the separation metrics of mobile phases modified with FA and FA/AF and explores the use of FA/AF for the LC-MS analysis of tryptic digests. Standard tryptic-digest peptides were used for comparative analysis of peak capacity and sample load tolerance. The compatibility of FA/AF in proteomic applications was examined with the analysis of soluble proteins from canine prostate carcinoma tissue. Overall, the use of FA/AF improved online RP-LC separations and led to significant increases in peptide identifications with improved protein sequence coverage.

Optimized superficially porous particles for protein separations.

Continuing interest in larger therapeutic molecules by pharmaceutical and biotech companies provides the need for improved tools for examining these molecules both during the discovery phase and later during quality control. To meet this need, larger pore superficially porous particles with appropriate surface properties (Fused-Core(®) particles) have been developed with a pore size of 400 Å, allowing large molecules (<500 kDa) unrestricted access to the bonded phase. In addition, a particle size (3.4 µm) is employed that allows high-efficiency, low-pressure separations suitable for potentially pressure-sensitive proteins. A study of the shell thickness of the new fused-core particles suggests a compromise between a short diffusion path and high efficiency versus adequate retention and mass load tolerance. In addition, superior performance for the reversed-phase separation of proteins requires that specific design properties for the bonded-phase should be incorporated. As a result, columns of the new particles with unique bonded phases show excellent stability and high compatibility with mass spectrometry-suitable mobile phases. This report includes fast separations of intact protein mixtures, as well as examples of very high-resolution separations of larger monoclonal antibody materials and associated variants. Investigations of protein recovery, sample loading and dynamic range for analysis are shown. The advantages of these new 400 Å fused-core particles, specifically designed for protein analysis, over traditional particles for protein separations are demonstrated.

Optimization of data-dependent acquisition parameters for coupling high-speed separations with LC-MS/MS for protein identifications.

Recent developments in chromatography, such as ultra-HPLC and superficially porous particles, offer significantly improved peptide separation. The narrow peak widths, often only several seconds, can permit a 15-min liquid chromatography run to have a similar peak capacity as a 60-min run using traditional HPLC approaches. In theory, these larger peak capacities should provide higher protein coverage and/or more protein identifications when incorporated into a proteomic workflow. We initially observed a decrease in protein coverage when implementing these faster chromatographic approaches, due to data-dependent acquisition (DDA) settings that were not properly set to match the narrow peak widths resulting from newly implemented, fast separation techniques. Oversampling of high-intensity peptides lead to low protein-sequence coverage, and tandem mass spectra (MS/MS) from lower-intensity peptides were of poor quality, as automated MS/MS events were occurring late on chromatographic peaks. These observations led us to optimize DDA settings to use these fast separations. Optimized DDA settings were applied to the analysis of Trypanosome brucei peptides, yielding peptide identifications at a rate almost five times faster than previously used methodologies. The described approach significantly improves protein identification workflows that use typical available instrumentation.

An improved approach to hydrophilic interaction chromatography of peptides: salt gradients in the presence of high isocratic acetonitrile concentrations.

Hydrophilic interaction chromatography (HILIC) for separations of peptides has been employed infrequently, particularly considering that this technique was introduced over 20 years ago. The present manuscript describes a radical departure from the traditional HILIC elution approach, where separations are achieved via increasing salt (sodium perchlorate) gradients in the presence of high isocratic concentrations (>80%) of acetonitrile, denoted HILIC/SALT. This initial study compared to reversed-phase chromatography (RPC), HILIC and HILIC/SALT for the separation of mixtures of synthetic peptide standards varying in structure (amphipathic α-helix, random coil), length (10-26 residues), number of positively charged residues (+1 to +11) and hydrophilicity/hydrophobicity. Results showed a marked superiority of the HILIC/SALT approach compared to traditional HILIC and excellent complementarity to RPC for peptide separations. We believe these initial results offer a new dimension to HILIC, enabling it to transform from an occasional HPLC approach for peptide separations to a more generally applicable method.