ABSTRACT
Millimeter-wave (mmWave) radars attain high resolution without compromising privacy while being unaffected by environmental factors such as rain, dust, and fog. This study explores the challenges of using mmWave radars for the simultaneous detection of people and small animals, a critical concern in applications like indoor wireless energy transfer systems. This work proposes innovative methodologies for enhancing detection accuracy and overcoming the inherent difficulties posed by differences in target size and volume. In particular, we explore two distinct positioning scenarios that involve up to four mmWave radars in an indoor environment to detect and track both humans and small animals. We compare the outcomes achieved through the implementation of three distinct data-fusion methods. It was shown that using a single radar without the application of a tracking algorithm resulted in a sensitivity of 46.1%. However, this sensitivity significantly increased to 97.10% upon utilizing four radars using with the optimal fusion method and tracking. This improvement highlights the effectiveness of employing multiple radars together with data fusion techniques, significantly enhancing sensitivity and reliability in target detection.
Subject(s)
Algorithms , Privacy , Animals , Humans , Reproducibility of Results , Energy Transfer , RadarABSTRACT
The effective deployment of Internet of Things (IoT) applications such as smart cities, smart farming and smart transport systems must ensure the network robustness, scalability and longevity. Therefore, guaranteeing the successful delivery of information and extending the lifetime of the nodes that make up a wireless sensor network (WSN) are two essential aspects for IoT applications. This work evaluates the performance of a cooperative WSN by adopting two multiantenna schemes: antenna selection (AS) and beamforming transmission using the singular value decomposition (SVD) technique. In addition, cooperation is established according to an ON-OFF probability, so that the RF receiving circuits of the relays are activated in a probabilistic way, aiming at reducing the energy consumption of the sensors, extending their useful lifetime. Our main goal is to increase the amount of information effectively transmitted by the network, keeping an outage probability constraint. The results show that, when both techniques are used, there is a significant gain in the amount of information effectively transmitted by the network, with emphasis on the AS scheme at short transmission distances. By increasing the number of antennas, it was found that a lower ON-OFF probability is required, i.e., a trade-off is established between the nodes' hardware complexity and their need for cooperation.
ABSTRACT
Energy-efficiency is crucial for modern radio-frequency (RF) receivers dedicated to Internet of Things applications. Energy-efficiency enhancements could be achieved by lowering the power consumption of integrated circuits, using antenna diversity or even with an association of both strategies. This paper compares two wideband RF front-end architectures, based on conventional low-noise amplifiers (LNA) and low-noise transconductance amplifiers (LNTA) with N-path filters, operating with three transmission schemes: single antenna, antenna selection and singular value decomposition beamforming. Our results show that the energy-efficiency behavior varies depending on the required communication link conditions, distance between nodes and metrics from the front-end receivers. For short-range scenarios, LNA presents the best performance in terms of energy-efficiency mainly due to its very low power consumption. With the increasing of the communication distance, the very low noise figure provided by N-path LNTA-based architectures outperforms the power consumption issue, yielding higher energy-efficiency for all transmission schemes. In addition, the selected front-end architecture depends on the number of active antennas at the receiver. Hence, we can observe that low noise figure is more important with a few active antennas at the receiver, while low power consumption becomes more important when the number of active RF chains at the receiver increases.
ABSTRACT
Wireless Sensors Networks (WSNs) are an essential element of the Internet of Things (IoT), and are the main producers of big data. Collecting a huge amount of data produced by a resource-constrained network is a very difficult task, presenting several challenges. Big data gathering involves not only periodic data sensing, but also the forwarding of queries and commands to the network. Conventional network protocols present unfeasible strategies for large-scale networks and may not be directly applicable to IoT environments. Information-Centric Networking is a revolutionary paradigm that can overcome such big data gathering challenges. In this work, we propose a soft-state information-centric protocol, ICENET (Information Centric protocol for sEnsor NETworks), for big data gathering in large-scale WSNs. ICENET can efficiently propagate user queries in a wireless network by using a soft-state recovery mechanism for lossy links. The scalability of our solution is evaluated in different network scenarios. Results show that the proposed protocol presents approximately 84% less overhead and a higher data delivery rate than the CoAP (Constrained Application Protocol), which is a popular protocol for IoT environments.
ABSTRACT
Underwater acoustic networks (UAN) allow for efficiently exploiting and monitoring the sub-aquatic environment. These networks are characterized by long propagation delays, error-prone channels and half-duplex communication. In this paper, we address the problem of energy-efficient communication through the use of optimized channel coding parameters. We consider a two-layer encoding scheme employing forward error correction (FEC) codes and fountain codes (FC) for UAN scenarios without feedback channels. We model and evaluate the energy consumption of different channel coding schemes for a K-distributed multipath channel. The parameters of the FEC encoding layer are optimized by selecting the optimal error correction capability and the code block size. The results show the best parameter choice as a function of the link distance and received signal-to-noise ratio.
