ABSTRACT
The process of chemical modification of tar and oxidized bitumen with formalin (a 37% aqueous solution of formaldehyde) in a hermetic container was investigated and the effectiveness of the proposed process was proven. It is shown that the most effective raw material for the process is tar, not oxidized bitumen. The expediency and impact of using different types of solvents (toluene, p-xylene and petroleum solvent, and n-octane) in the modification process were studied. It was established that the solvent should be used in the modification of oxidized bitumens, not tars. The low efficiency of the process of tar modification with formaldehyde without the use of a catalyst was proven, and it was shown that the most active catalyst in the process is sulfuric acid. The influence and optimal values of the main factors controlling the process of chemical modification of tar with formaldehyde were established, namely temperature, duration, and content of the modifier-formaldehyde. On the basis of the found regularities and optimal conditions of the modification process, samples of binding materials (of different brands) with different operational characteristics were obtained, and their comprehensive research was carried out. With the help of FTIR spectroscopy, the chemical interaction of tar with formaldehyde in the presence of an acid catalyst was confirmed. The design of the compositions of asphalt concrete mixtures using formaldehyde-modified tar was carried out, from which cylindrical samples of stone mastic asphalt (SMA-15 brand) were obtained, which were tested according to the main indicators: average density, water-saturation, compression strength at 20 and 50 °C, compression strength after water-saturation (MPa) at 50 °C.
ABSTRACT
Due to the increasingly higher requirements for rubber vulcanizates, following the example of previous research on the effect of resin addition on mechanical properties and adhesion of rubbers, the following studies investigated the relationship between the addition of adipic acid-modified epoxy dian resin (ED-24 AK) to butadiene-acrylonitrile rubber (NBR). It can be seen that the addition of ED-24 AK, compared to the reference additive ED-20 (Epidian 5), additionally increase crosslinking density of the system, changes its mechanical and tribological properties, and exerts a positive effect on adhesion of the rubber vulcanizates to glass fiber. ED-20 and ED-24 AK resins do not enter the structure of the vulcanized rubber but act as the additives. ED-20 acts without changes in its structure, and ED-24 AK is a partially crosslinked additive. Modification, especially with ED-24 AK, makes mechanical strength of NBR increased even up to 240% in comparison to virgin rubber vulcanizate. This is responsible for lower friction of the vulcanizates. The decrease in the friction force of NBR due to the modified dian resin addition can reach up to 40%. Adhesion of the modified NBR to glass fibers increases due to its modification with the epoxy resins, however this time the ED-24 is more efficient than ED-24 AK reaching ca. 50% increase comparing to ca. 20% improvement, respectively. The best performance of the resins Generally, the best modification results were obtained when the addition of resins did not exceed 5 phr.
ABSTRACT
With the continuing growth of waste sulfur production from the petroleum industry processes, its utilization for the production of useful, low-cost, and environmentally beneficial materials is of primary interest. Elemental sulfur has a significant and established history in the modification of bitumen binders, while the sulfur-containing high-molecular compounds are limited in this field. Herein, we report a novel possibility to utilize the sulfur/organic copolymers obtained via the inverse vulcanization process as modifiers for bitumen binders. Synthesis and thermal characterization (TGA-DSC) of polysulfides derived from elemental sulfur (S8) and unsaturated organic species (dicyclopentadiene, styrene, and limonene) have been carried out. The performance of modified bitumen binders has been studied by several mechanical measurements (softening point, ductility, penetration at 25 °C, frass breaking point, adhesion to glass and gravel) and compared to the unmodified bitumen from the perspective of normalized requirements concerning polymer-modified bitumen. The interaction of bitumen binder with sulfur/organic modifier has been studied by means of FTIR spectroscopy and DSC measurements. The impact of the modification on the performance properties of bitumen has been demonstrated. The bitumen binders modified with sulfur/organic copolymers are in general less sensitive to higher temperatures (higher softening point up to 7 °C), more resistant to permanent deformations (lower penetration depth), and more resistant to aging processes without intrusive deterioration of parameters at lower temperatures. What is more, the modification resulted in significantly higher adhesion of bitumen binders to both glass (from 25% up to 87%) and gravel surfaces in combination with a lower tendency to form permanent deformations (more elastic behavior of the modified materials).
ABSTRACT
In this study, well-known oligomers containing ethyl methacrylate (EMA) and glycidyl methacrylate (GMA) components for the synthesis of the oligomeric network [P(EMA)-co-(GMA)] were used. In order to change the hydrophobic character of the [P(EMA)-co-(GMA)] to a more hydrophilic one, the oligomeric chain was functionalized with ethanolamine, xylitol (Xyl), and L-ornithine. The oligomeric materials were characterized by nuclear magnetic resonance and Fourier transform infrared spectroscopy, scanning electron microscopy, and differential thermogravimetric analysis. In the final stage, thanks to the large amount of -OH groups, it was possible to obtain a three-dimensional hydrogel (HG) network. The HGs were used as a matrix for the immobilization of methylene blue, which was chosen as a model compound of active substances, the release of which from the matrix was examined using spectrophotometric detection. The cytotoxic test was performed using fluid extracts of the HGs and human skin fibroblasts. The cell culture experiment showed that only [P(EMA)-co-(GMA)] and [P(EMA)-co-(GMA)]-Xyl have the potential to be used in biomedical applications. The studies revealed that the obtained HGs were porous and non-cytotoxic, which gives them the opportunity to possess great potential for use as an oligomeric network for drug reservoirs in in vitro application.
Subject(s)
Epoxy Compounds/chemistry , Fibroblasts/drug effects , Hydrogels/chemistry , Methacrylates/chemistry , Microwaves , Polymers/pharmacology , Skin/drug effects , Humans , Hydrophobic and Hydrophilic Interactions , Polymers/chemistryABSTRACT
The research was aimed at checking the effect of monoperoxy derivative of epoxy resin (PO) on the possibility of rubber crosslinking and a subsequent adhesion of the modified rubber to silver wires. Three of the commonly industrially used rubbers were selected for the study: styrene-butadiene rubber (SBR), acrylonitrile-butadiene rubber (NBR) and carboxylated acrylonitrile-butadiene rubber (XNBR), together with the popular, commercially available Epidian 6 epoxy resin, subjected to the functionalization. An improvement in the adhesion of rubbers to silver wires was observed when using the modified resin. In some cases, an improvement in the mechanical properties of the rubber was observed, especially when the resin was used for crosslinking together with dicumyl peroxide (DCP). Crosslinking synergy between dicumyl peroxide and the modified resin could be observed especially in the case of PO applied for peroxide curing of SBR and NBR.
ABSTRACT
This research was aimed at verifying the effect of carboxy-containing peroxy oligomer (CPO) addition on the possibility of rubber crosslinking and a subsequent adhesion of the modified rubber to silver wires. Three commonly industrially used rubbers were selected for the study: styrene-butadiene rubber (SBR), acrylonitrile-butadiene rubber (NBR) and carboxylated acrylonitrile-butadiene rubber (XNBR), together with carboxy-containing peroxy oligomer (CPO). An improvement in the adhesion of rubbers to silver wires was observed when applying the oligomeric peroxide with functional groups, with no deterioration of mechanical properties of the vulcanizates. Crosslinking synergy between dicumyl peroxide (DCP) and the modifier could hardly be observed. Nevertheless, the studies demonstrated, that to a small extent, even the CPO itself can crosslink NBR and especially XNBR, resulting in a material of notable elasticity and adhesion to silver wires.
