Synapsid tracks with skin impressions illuminate the terrestrial tetrapod diversity in the earliest Permian of equatorial Pangea.

Lower Permian deposits of the Boskovice Basin in the Czech Republic have long been renowned for extraordinarily abundant specimens of discosauriscid seymouriamorphs, some of which showing exceptional preservation, including widespread soft tissues. The only other tetrapods from the strata are represented by rare temnospondyls. However, recent fieldwork in the Asselian (lowermost Permian) of the Boskovice Basin has yielded a diverse assemblage of tetrapod tracks, illuminating a hidden terrestrial tetrapod diversity. Here, we describe well-preserved isolated tracks, manus-pes couples, and a slab with trackways composed of approximately 20 tracks in at least four different directions belonging to early-diverging, or 'pelycosaur-grade', synapsids. The material originates from three localities situated within the Letovice and Padochov formations and is assignable to the ichnotaxon Dimetropus. The best-preserved specimen further shows rare skin impressions, which have not been observed from the hands or feet of early-diverging mammal-line amniotes before. The new material adds to the scarce record of synapsids from the Carboniferous/Permian transitional interval of equatorial Pangea. At the same time, it highlights the significance of the ichnological record of the Boskovice Basin which has long been neglected despite offering evidence for the presence of diverse faunal components that have not been reported from these basinal deposits before.

Plastic Anisotropy Effect on Variation of Mechanical and Structural Properties of VT23 Titanium Alloy Subjected to Impact-Oscillatory Loading.

The main regularities in the impact of varying intensity impact-oscillatory loading on the variation of the mechanical and structural properties of the VT23 high-strength two-phase transverse-rolled sheet titanium alloy have been found. The intensity of the impulse introduction of energy into the alloy under the dynamic non-equilibrium process (DNP) was estimated by εimp (the increment of dynamic strain). The pulse intensity was found to change the shape of the static strain diagram with further tensioning, as compared to the initial state. This indicates the effect from the structure self-organization inherent in the VT23 titanium alloy upon the DNP. After the DNP (εimp = 1.44%), with further static deformation, the tensile diagram revealed yield sites up to 6.5% long. In most cases, the DNP was found to have a negative effect on the variation of the mechanical properties of the VT23 titanium alloy, especially if the latter was rolled in the transverse direction. The optimal DNP intensity is εimp~1.5%. In this case, the DNP can be used as an effective plasticization technology for the VT23 titanium alloy (regardless of the rolling direction) in the stamping of high-strength titanium alloys. Changes in the mechanical and structural condition of the VT23 titanium alloy subjected to the DNP were confirmed by the fractographic investigation of specimen fractures.

Impact of the Initial Phase Composition of Alloys on the Effects Manifested by Yield Sites That Occur on Sheet Aluminum Alloys Subjected to Impact-Oscillatory Loading.

The impact of the initial phase composition of alloys was evaluated, in particular, the content of Cu, Mn, and Mg in aluminum alloys D16ChATW, 2024-T351 and aluminum alloy T, which in its physical and mechanical characteristics is close to alloy 6013. The impact was evaluated on the effects manifested by yield sites that occur on aluminum alloys that were subject to the dynamic non-equilibrium processes (DNPs) at the expense of impact-oscillatory loading of different intensities under conditions of static tensioning, The one-time DNP, to which the investigated aluminum alloys were subjected at the pre-set levels of elastic strain followed by static tensioning, was found to cause yield sites formation. This is due to self-organization of the alloy structure, which contributes to alloy plasticization. The initial phase alloys composition impact on the yield sites, which occurs when impulse energy of a different intensity is applied to the alloys, was analyzed. The specimens from the aluminum alloys undergoing DNPs of the same level were compared. This made it possible to conclude that alloys D16ChATW and 2024-T351, which have a higher content of Cu, Mn, and Mg, have longer yield sites upon subsequent static tensioning. On the basis of the experimental results, in particular, physical studies, the authors derived a physical and mathematical model of the yield sites that appear after DNPs.

Properties Evaluation of the Welded Joints Made by Disk Laser.

The process of laser welding of sheets of HSLA (high-strength low-alloy steel), DP600 (dual-phase steel) and TRIP steels was investigated. A weld was successfully made in a double-sided hot-dip galvanized sheet with a thickness of 0.78-0.81 mm using a laser power of 2 kW per pass without any pretreatment of the weld zone. Microstructure studies revealed the presence of martensitic and ferritic phases in the weld zone, which could be associated with a high rate of its cooling. This made it possible to obtain good strength of the weld, while maintaining sufficient ductility. A relationship between the microstructural features and mechanical properties of welds made in the investigated steels has been established. The highest hardness was found in the alloying region of steels due to the formation of martensite. The hardness test results showed a very narrow soft zone in the heat affected zone (HAZ) adjacent to the weld interface, which does not affect the tensile strength of the weld. The ultimate tensile strength of welds for HSLA steel was 340-450 MPa, for DP600 steel: 580-670 MPa, for TRIP steel: ~700 MPa, respectively, exceeding the strength of base steels.

Restoration of Worn Movable Bridge Props with Use of Bronze Claddings.

This article examined the possibility of using CuSn6P claddings in sliding bearing renovation of movable pontoon bridge props. The bronze layer was welded on cylinders of the high-strength steel S355J0WP EN 10155-93, in an inert atmosphere using an automated welding method (gas tungsten arc welding). Pulsed arc welding was used to minimize the effects of heat on the cladding area, while also accounting for the differences in the physical properties of the joined metals. The sliding bearing was created in two layers. The quality of the cladding layer was evaluated by nondestructive and/or destructive tests. The quality of the surface was assessed by visual inspection (visual testing) in accordance with the EN ISO 17637 standard. The quality of the claddings was evaluated by metallographic analysis, performed using light microscopy. The microhardness values of a few weld areas were determined by Vickers tests, performed according to the EN ISO 9015-2 standard. The analyses confirmed that the welding parameters and filler material used resulted in high-quality weld joints with no internal (subsurface) or metallurgical defects.