ABSTRACT
Radio frequency (RF) driven H- ion sources are operated at very high power levels of up 100 kW in order to achieve the desired performance. For the experimental setup, these are demanding conditions possibly limiting the source reliability. Therefore, assessing the optimization potential in terms of RF power losses and the RF power transfer efficiency η to the plasma has moved to the focus of both experimental and numerical modeling investigations at particle accelerator and neutral beam heating sources for fusion plasmas. It has been demonstrated that, e.g., at typical neutral beam injection ion source setups, about half of the RF power provided by the generator is lost in the RF coil and the Faraday shield due to Joule heating or via eddy currents. In a best practice approach, it is exemplarily demonstrated at the ITER RF prototype ion source how experimental evaluation accompanied by numerical modeling of the ion source can be used to improve η. Individual optimization measures regarding the Faraday shield, the RF coil, the discharge geometry, the RF driving frequency, and the application of ferrites are discussed, which could reduce the losses by a factor of two. The provided examples are intended as exemplary guidelines, which can be applied at other setups in order to achieve with low-risk effort an optimized ion source design in terms of reduced losses and hence increased reliability.
ABSTRACT
The target parameters of negative ion sources regarding the current of extracted negative ions, the current of co-extracted electrons, the pulse duration, the duty cycle, and the availability of the system can be rather strict. Knowledge of plasma parameters such as the electron temperature and the electron density and also properties of molecules or photon fluxes can provide essential insights into the ion source physics needed for reaching the target parameters. Emission spectroscopy is a non-invasive tool enabling access to line-of-sight averaged values of plasma parameters. This paper gives an overview of the application of emission spectroscopy in the visible range, extended for long wavelengths to the near-IR and for short wavelengths to the vacuum ultraviolet (VUV)/UV range. The amount of information to be gained from measured emission spectra is directly correlated with the effort invested for calibrating the system. Examples are given, ranging from simple monitoring to the complex evaluation of molecular spectra and the determination of highly energetic photon fluxes in the VUV/UV range. Additional emphasis is laid on the population models needed for the interpretation of measured spectra.
ABSTRACT
Optical emission spectroscopy (OES) measurements of the atomic Balmer series and the molecular Fulcher transition have been carried out at the Linac4 ion source in order to determine plasma parameters. As the spectroscopic system was only relatively calibrated, the data evaluation only yielded rough estimates of the plasma parameters (T(e) ≈ 1.2 eV, n(e) ≈ 1 × 10(19) m(-3), and n(H/)n(H2) ≈ 0.5 at standard operational parameters). The analysis of the Fulcher transition revealed a non-thermal "hockey-stick" rotational population of the hydrogen molecules. At varying RF power, the measurements at the on-axis line of sight (LOS) showed a peak in the rotational temperatures between 25 and 40 kW of RF power, whereas a steady decrease with power was observed at a tilted LOS, indicating the presence of strong plasma parameter gradients.
ABSTRACT
CERN's 160 MeV H(-) linear accelerator (Linac4) is a key constituent of the injector chain upgrade of the Large Hadron Collider that is being installed and commissioned. A cesiated surface ion source prototype is being tested and has delivered a beam intensity of 45 mA within an emittance of 0.3 π â mm â mrad. The optimum ratio of the co-extracted electron- to ion-current is below 1 and the best production efficiency, defined as the ratio of the beam current to the 2 MHz RF-power transmitted to the plasma, reached 1.1 mA/kW. The H(-) source prototype and the first tests of the new ion source optics, electron-dump, and front end developed to minimize the beam emittance are presented. A temperature regulated magnetron H(-) source developed by the Brookhaven National Laboratory was built at CERN. The first tests of the magnetron operated at 0.8 Hz repetition rate are described.
ABSTRACT
Large RF driven negative hydrogen ion sources are being developed at IPP Garching for the future neutral beam injection system of ITER. The overall power efficiency of these sources is low, because for the RF power supply self-excited generators are utilized and the plasma is generated in small cylindrical sources ("drivers") and expands into the source main volume. At IPP experiments to reduce the primary power and the RF power required for the plasma production are performed in two ways: The oscillator generator of the prototype source has been replaced by a transistorized RF transmitter and two alternative driver concepts, a spiral coil, in which the field is concentrated by ferrites, which omits the losses by plasma expansion and a helicon source are being tested.
ABSTRACT
In order to allow for a systematic investigation of the plasma properties of discharges containing indium halides, which are proposed as an efficient alternative for mercury based low pressure discharge lamps, a controlled variation of the indium halide density is mandatory. This can be achieved by applying a newly designed setup in which a well-defined cold spot location is implemented and the cold spot temperature can be adjusted between 50 and 350 °C without influencing the gas temperature. The performance of the setup has been proved by comparing the calculated evaporated InBr density (using the vapor pressure curve) with the one measured via white light absorption spectroscopy.
