Protein distribution in lupin protein isolates from Lupinus angustifolius L. prepared by various isolation techniques.

Differences in the protein distribution of various protein isolates from Lupinus angustifolius L. Vitabor were identified as affected by the isolation procedure (alkaline and/or salt-induced extraction followed by isoelectric and/or dilutive precipitation). Protein isolates extracted in alkaline solution showed higher protein yields (26.4-31.7%) compared to salt-induced extraction (19.8-30.0%) or combined alkaline and salt-induced extraction (23.3-25.6%). Chemical variations among the protein isolates especially occurred within the albumins. Protein isolates precipitated isoelectrically showed the highest contents, whereas protein isolates precipitated by dilutive showed the lowest contents of conglutin δ. Furthermore, the alkaline subunits of conglutin α and conglutin γ decreased during alkaline extraction compared to salt-induced extraction. A decrease in protein-bound polar and basic amino acids was shown after protein isolation. In contrast, the amounts of nonpolar, aliphatic, aromatic, hydroxylated and sulfur-rich amino acids were higher in the lupin protein isolates compared to the lupin flakes. However, the functional side chains could not be related to the specific molecular arrangements of the protein isolates, as a similar amino acid composition was found among the protein isolates.

Improved identification of wheat gluten proteins through alkylation of cysteine residues and peptide-based mass spectrometry.

The concentration and composition of wheat gluten proteins and the presence, concentration and location of cysteine residues therein are important for wheat flour quality. However, it is difficult to identify gluten proteins, as they are an extremely polymorphic mixture of prolamins. We here present methods for cysteine labeling of wheat prolamins with 4-vinylpyridine (4-VP) and iodoacetamide (IDAM) which, as compared to label-free analysis, substantially improve identification of cysteine-containing peptides in enzymic prolamin digests by electrospray ionization--tandem mass spectrometry. Both chymotrypsin and thermolysin yielded cysteine-containing peptides from different gluten proteins, but more proteins could be identified after chymotryptic digestion. In addition, to the best of our knowledge, we were the first to label prolamins with isotope coded affinity tags (ICAT), which are commonly used for quantitative proteomics. However, more peptides were detected after labeling gluten proteins with 4-VP and IDAM than with ICAT.

Identification of intact high molecular weight glutenin subunits from the wheat proteome using combined liquid chromatography-electrospray ionization mass spectrometry.

The present paper describes a method for the identification of intact high molecular weight glutenin subunits (HMW-GS), the quality determining proteins from the wheat storage proteome. The method includes isolation of HMW-GS from wheat flour, further separation of HMW-GS by reversed-phase high-performance liquid chromatography (RP-HPLC), and their subsequent molecular identification with electrospray ionization mass spectrometry using a quadrupole-time-of-flight mass analyzer. For HMW-GS isolation, wheat proteins were reduced and extracted from flour with 50% 1-propanol containing 1% dithiothreitol. HMW-GS were then selectively precipitated from the protein mixture by adjusting the 1-propanol concentration to 60%. The composition of the precipitated proteins was first evaluated by sodium dodecyl sulfate-polyacrylamide gel electrophoresis with Coomassie staining and RP-HPLC with ultraviolet detection. Besides HMW-GS (≥65%), the isolated proteins mainly contained ω5-gliadins. Secondly, the isolated protein fraction was analyzed by liquid chromatography-mass spectrometry. Optimal chromatographic separation of HMW-GS from the other proteins in the isolated fraction was obtained when the mobile phase contained 0.1% trifluoroacetic acid as ion-pairing agent. Individual HMW-GS were then identified by determining their molecular masses from the high-resolution mass spectra and comparing these with theoretical masses calculated from amino acid sequences. Using formic acid instead of trifluoroacetic acid in the mobile phase increased protein peak intensities in the base peak mass chromatogram. This allowed the detection of even traces of other wheat proteins than HMW-GS in the isolated fraction, but the chromatographic separation was inferior with a major overlap between the elution ranges of HMW-GS and ω-gliadins. Overall, the described method allows a rapid assessment of wheat quality through the direct determination of the HMW-GS composition and offers a basis for further top-down proteomics of individual HMW-GS and the entire wheat glutenin fraction.

Identification of isopeptide bonds in heat-treated wheat gluten peptides.

Results in this paper confirm heat-induced isopeptide bond formation in wheat gluten. Heating (24 h, 130 °C) of wheat gluten [moisture content 7.4%] decreased its extractability in sodium dodecyl sulfate containing buffer (pH 6.8), even after reduction of disulfide (SS) bonds. Thus, both SS bonds and non-SS bonds were responsible for the extractability loss. Cross-links of the lysinoalanine and lanthionine type were not present in the heated samples, but heat treatment reduced levels of available amino groups. Heating of purified and alkylated high molecular weight glutenin subunits (HMW-GS) under similar conditions also resulted in extractability loss, demonstrating that cross-linking did not solely depend on the availability of cysteine or cystine. These observations indicated that heat treatment had induced isopeptide bond formation, resulting in larger and unextractable molecules. Heating HMW-GS lysine- and glutamine-containing peptides induced the formation of isopeptide bonds, thereby supporting the above hypothesis. The level of isopeptide bond formation increased with heating time.

Divalent metal nanoparticles.

Nanoparticles can be used as the building blocks for materials such as supracrystals or ionic liquids. However, they lack the ability to bond along specific directions as atoms and molecules do. We report a simple method to place target molecules specifically at two diametrically opposed positions in the molecular coating of metal nanoparticles. The approach is based on the functionalization of the polar singularities that must form when a curved surface is coated with ordered monolayers, such as a phase-separated mixture of ligands. The molecules placed at these polar defects have been used as chemical handles to form nanoparticle chains that in turn can generate self-standing films.

Low-voltage organic transistors with an amorphous molecular gate dielectric.

Organic thin film transistors (TFTs) are of interest for a variety of large-area electronic applications, such as displays, sensors and electronic barcodes. One of the key problems with existing organic TFTs is their large operating voltage, which often exceeds 20 V. This is due to poor capacitive coupling through relatively thick gate dielectric layers: these dielectrics are usually either inorganic oxides or nitrides, or insulating polymers, and are often thicker than 100 nm to minimize gate leakage currents. Here we demonstrate a manufacturing process for TFTs with a 2.5-nm-thick molecular self-assembled monolayer (SAM) gate dielectric and a high-mobility organic semiconductor (pentacene). These TFTs operate with supply voltages of less than 2 V, yet have gate currents that are lower than those of advanced silicon field-effect transistors with SiO2 dielectrics. These results should therefore increase the prospects of using organic TFTs in low-power applications (such as portable devices). Moreover, molecular SAMs may even be of interest for advanced silicon transistors where the continued reduction in dielectric thickness leads to ever greater gate leakage and power dissipation.