ABSTRACT
This paper presents a critical review of the main research progress and application of Shirasu concretes in Japan recently. As a kind of pyroclastic-flow deposits, Shirasu aggregate was considered as one kind of nonstandard aggregates for modern concrete industries because it usually has a low density and a high water content rate, and also contains a large amount of fine powder on its surface. However, with the considerations that Shirasu has a high level of pozzolanic activity and can be available widely and easily in Japan, many studies had been performed in Japan in the last two decades. The key concerns in the paper focus on the basic fresh properties of Shirasu raw material, the mix design, and the basic material properties of Shirasu concretes. Based on this review, several recommendations were provided for future works. Through the review, Shirasu concrete considered as a construction material could present accepted material properties compared with traditional concrete, including basic fresh and mechanical, and durability properties. It was suggested to apply concrete structures with careful concerns and recommended to structures under several special environments. Using this aggregate, several kinds of high-performance concrete also could be produced.
Subject(s)
Recycling , Waste Management , Construction Materials , Industrial Waste/analysis , JapanABSTRACT
The influence of using cement on the residual properties of fly ash geopolymer concrete (FAGC) after exposure to high temperature of up to 800 °C was studied in terms of mass loss, residual compressive strength and microstructure. The mass loss was found to increase with the increase of exposure temperature, which is attributed to vaporization of water and dehydroxylation of sodium aluminosilicate hydrate (N-A-S-H) gels. The dehydroxylation of calcium silicate hydrate (C-S-H) gels and the disintegration of portlandite were responsible for higher mass loss ratio of FAGCs containing cement. The results showed that cement could increase compressive strength of FAGCs up to 200 °C, after which a significant reduction in residual strength was observed. It was found that FAGCs without cement yielded higher residual strength than the original strength after heating up to 600 °C. The observed increase of compressive strength up to 200 °C was attributed to the secondary geopolymerization which was evidenced in the scanning electronic microscopy (SEM) images.
ABSTRACT
In this study, conductive carbon nanofibers (CNFs) were dispersed into epoxy resin and then infused into glass fiber fabric to fabricate CNF/glass fiber-reinforced polymer (GFRP) laminates. The electrical resistance and strain of CNF/GFRP laminates were measured simultaneously during tensile loadings to investigate the in situ strain and damage monitoring capability of CNF/GFRP laminates. The damage evolution and conduction mechanisms of the laminates were also presented. The results indicated that the percolation threshold of CNFs content for CNF/GFRP laminates was 0.86 wt % based on a typical power law. The resistance response during monotonic tensile loading could be classified into three stages corresponding to different damage mechanisms, which demonstrated a good ability of in situ damage monitoring of the CNF/GFRP laminates. In addition, the capacity of in situ strain monitoring of the laminates during small strain stages was also confirmed according to the synchronous and reversible resistance responses to strain under constant cyclic tensile loading. Moreover, the analysis of the resistance responses during incremental amplitude cyclic tensile loading with the maximum strain of 1.5% suggested that in situ strain and damage monitoring of the CNF/GFRP laminates were feasible and stable.
ABSTRACT
This paper presents an experimental study of the basic properties of the main materials found in reinforced concrete (RC) structures strengthened by fibre reinforced polymer (FRP) sheets with scope to investigate the effect of ultraviolet (UV) exposure on the degradation of FRP, resin adhesive materials and concrete. The comparison studies focused on the physical change and mechanical properties of FRP sheet, and resin adhesive materials and concrete before and after UV exposure. However, the degradation mechanisms of the materials under UV exposure were not analyzed. The results show that the ultimate tensile strength and modulus of FRP sheets decrease with UV exposure time and the main degradation of FRP-strengthened RC structures is dependent on the degradation of resin adhesive materials. The increase in the number of FRP layers cannot help to reduce the effect of UV exposure on the performance of these materials. However, it was verified that carbon FRP materials have a relatively stable strength and elastic modulus, and the improvement of the compression strength of concrete was also observed after UV exposure.
ABSTRACT
Massive volcano-related materials (VRMs) erupted from volcanoes bring the impacts to natural environment and humanity health worldwide, which include generally volcanic ash (VA), volcanic pumice (VP), volcanic tuff (VT), etc. Considering the pozzolanic activities and mechanical characters of these materials, civil engineers propose to use them in low carbon/cement and environment-friendly concrete industries as supplementary cementitious materials (SCMs) or artificial/natural aggregates. The utilization of VRMs in concretes has attracted increasing and pressing attentions from research community. Through a literature review, this paper presents comprehensively the properties of VRMs and VRM concretes (VRMCs), including the physical and chemical properties of raw VRMs and VRMCs, and the fresh, microstructural and mechanical properties of VRMCs. Besides, considering environmental impacts and the development of long-term properties, the durability and stability properties of VRMCs also are summarized in this paper. The former focuses on the resistance properties of VRMCs when subjected to aggressive environmental impacts such as chloride, sulfate, seawater, and freezing-thawing. The latter mainly includes the fatigue, creep, heat-insulating, and expansion properties of VRMCs. This study will be helpful to promote the sustainability in concrete industries, protect natural environment, and reduce the impacts of volcano disaster. Based on this review, some main conclusions are discussed and important recommendations regarding future research on the application of VRMs in concrete industries are provided.
