ABSTRACT
Applying protective or barrier layers to isolate a target item from the environment is a common approach to prevent or delay its degradation. The impermeability of two-dimensional materials such as graphene and hexagonal boron nitride (hBN) has generated a great deal of interest in corrosion and material science. Owing to their different electronic properties (graphene is a semimetal, whereas hBN is a wide-bandgap insulator), their protection behaviour is distinctly different. Here we investigate the performance of graphene and hBN as barrier coatings applied on copper substrates through a real-time study in two different oxidative conditions. Our findings show that the evolution of the copper oxidation is remarkably different for the two coating materials.
ABSTRACT
The relaxation dynamics of unaligned multi-walled carbon nanotubes decorated with metallic nanoparticles have been studied by using transient optical measurements. The fast dynamics due to the short-lived free-charge carriers excited by the pump are not affected by the presence of nanoparticles. Conversely, a second long dynamics, absent in bare carbon nanotubes, appears only in the decorated samples. A combination of experiment and theory allows us to ascribe this long dynamics to relaxation channels involving electronic states localized at the tube-nanoparticle interface.
ABSTRACT
The bulk synthesis of freestanding carbon nanotube (CNT) frameworks is developed through a sulfur-addition strategy during an ambient-pressure chemical vapour deposition process, with ferrocene used as the catalyst precursor. This approach enhances the CNTs' length and contorted morphology, which are the key features leading to the formation of the synthesized porous networks. We demonstrate that such a three-dimensional structure selectively uptakes from water a mass of toxic organic solvent (i.e. o-dichlorobenzene) about 3.5 times higher than that absorbed by individual CNTs. In addition, owing to the presence of highly defective nanostructures constituting them, our samples exhibit an oil-absorption capacity higher than that reported in the literature for similar CNT sponges.
Subject(s)
Chlorobenzenes/analysis , Nanotechnology/methods , Nanotubes, Carbon/chemistry , Water Pollutants, Chemical/analysis , Water Purification/methods , Water/chemistry , Absorption , Carbon/chemistry , Equipment Design , Filtration , Graphite/chemistry , Materials Testing , Microscopy, Electron, Scanning , Microscopy, Electron, Transmission , Oils/chemistry , Organic Chemicals/chemistry , Porosity , Solvents/chemistry , Spectrum Analysis, Raman , Surface PropertiesABSTRACT
We show that Cu metal nanoparticle-multiwall carbon nanotube (MWCNT) assemblies can act as a new hybrid photoactive layer in photo-electrochemical devices. The carbon nanotube (CNT) composites were formed by a controlled thermal deposition of copper which produced crystalline metal nanoparticles localized on the carbon tube outer walls. The photoresponse evaluated in terms of IPCE (incident photon-to-charge carrier generation efficiency) varied for different sized-Cu-MWCNT samples across all the visible and near ultraviolet photon energy range with respect to the response of bare MWCNTs. In the case of 0.2 nm Cu nominal thickness, the IPCE increased, reaching 15%, a value 2.5 times higher than that measured for bare MWCNTs. As the Cu nominal coverage thickened, the IPCE started to decrease and become totally ineffective after 1 nm deposited Cu. The IPCE increase found was interpreted as being the result of a remarkable charge transfer between the Cu metal nanoparticles and the CNTs due to the formation of a strong ionic bond at their interface. The results obtained prove that the metal nanoparticle-CNT composites have optical, electrical and structural properties that can be applied in a variety of nanoscale architectures for novel photo-electrochemical devices.
ABSTRACT
We report on the multiwall carbon nanotube application as energy conversion material to fabricate thin film solar cells, with nanotubes acting as photogeneration sites as well as charge separators, collectors and carrier transporters. The device consists of a semitransparent thin film of nanotubes coating a n-type crystalline silicon substrate. Under illumination electron-hole (e-h) pairs, generated in the nanotubes and in the silicon substrate underneath, are split and charges are transported through the nanotubes (electrons) and the n-Si (holes). We found that a suitable thickness of the nanotube thin film, high density of Schottky junctions between nanotubes and n-Si and lowest number of nanotube walls are all fundamental parameters to improve the device incident photon to electron conversion efficiency. Multiwall carbon nanotubes have been synthesized by chemical vapour deposition in an ultra high vacuum chamber by evaporating a given amount of iron at room temperature and then exposing the substrate kept at 800 degrees C at acetylene gas. The amount of deposited iron is found to directly affect the nanotube size distribution (inner and outer diameter) and therefore the number of walls of the nanotubes.
ABSTRACT
In this paper we illustrate a simple method for the production of multiwall carbon nanotubes thin films decorated with copper metal nanoparticles. The structural information obtained from the transmission electron microscopy study performed on samples differing in the quantity of deposited Copper was linked to the opto-electronic properties evaluated with photo-electrochemical measurements. The photo-response evaluated in terms of incident photon-to-charge carrier generation efficiency varied for different sized-Cu-multiwall carbon nanotubes samples across all the visible and near-ultraviolet photon energy range with respect to the response of bare carbon tubes. The photo-response from the sample covered with of 0.5 nm Cu nominal thickness, reached 10.2%, a value 2 times higher than that measured for bare carbon tubes of 5.9%. While this value decreased to 2.8% when the Cu nominal coverage thickened up to 3 nm. The increase in the photo-response found was interpreted as being the result of a remarkable charge transfer between the Cu metal nanoparticles and the carbon atoms in the tube due to the formation of a strong ionic bond at their interface. The results obtained prove that the metal nanoparticle-carbon nanotube composites have optical, electrical and structural properties that can be applied in a variety of nanoscale architectures for novel photo-electrochemical devices.
ABSTRACT
Densitometric measurements are prone to imprecision in elderly subjects and the present study was primarily designed to dissect out the effects of age and bone mineral density on proximal femur dual energy x-ray absorptiometry (DXA) reproducibility. The study comprised 17 elderly women (mean age 74.6 years, range 65-84 years), 13 early postmenopausal women with osteopenia (mean age 56.2 years, range 50-63 years), and 17 elderly men (mean age 73.8 years, range 65-86 years). Each subject was given triplicate proximal femur scans by a QDR 2000 Densitometer (Hologic Inc., Waltham, MA) with repositioning between scans. Because of subject selection in the early postmenopausal women there were no significant differences in bone mineral density (BMD) at any site among the three groups. Despite this, reproducibility errors expressed as either coefficient of variation (CV) % or mean standard deviation (SD) were greater in the elderly subjects, regardless of gender, when compared with the younger female subjects. The variability in measurement errors with age were least marked for the total hip and trochanteric sites. Within the elderly subjects, BMD appeared to exert little influence on measurement errors. We conclude that short-term proximal femur reproducibility is dependent on age-related factors other than BMD. There is no influence of gender on the measurement errors. It is likely that local factors (e.g., hip osteoarthritis) or general frailty may influence repositioning but this needs further exploration. In the meantime, the total hip and trochanteric sites should be used as they provide the most reproducible measurements in the elderly.