Preparation of molecularly imprinted polymers for artemisinin based on the surfaces of silica gel.

Artemisinin is an effective antimalarial drug isolated from the herbal medicine Artemisia annua L. Molecular imprinting is a technique of preparing molecularly imprinted polymers (MIPs) which can specifically recognize the imprinted template molecules. In this work, silica gel were used as supporting matrix, and vinyltriethoxysilane (VTES) was grafted onto its surface. The preparation of MIPs for artemisinin was performed on the surfaces of the modified silica gel using artemisinin as the template, acrylamide (AM) and methacrylic acid (MAA) as the functional monomers, ethylene glycol dimethacrylate (EGDMA) as the cross-linker and 2,2'-azo-bis-isobutyronitrile (AIBN) as the initiator. Scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR) and pore size analysis were used to characterize the prepared MIPs. The adsorption kinetic curve, adsorption isotherm and selective adsorption were measured by static method. The adsorption reached equilibrium at about 10 h, while fast adsorption took place during the first 2-3 h. The maximum adsorption capacity has been found to be 37.13 mg/g according to calculation with Langmuir-Freundlich isotherm. The electivity coefficients of MIPs for artemisinin with respect to artemether and arteether were 2.88 and 3.38, respectively. The results showed that the MIPs possessed good specific adsorption capacity and selectivity for artemisinin.

Synthesis of a novel pH-sensitive methacrylate amphiphilic polymer and its primary application in aqueous two-phase systems.

In this study, a novel pH-sensitive and reversible water-soluble polymer(P(ABC)) forming aqueous two-phase systems(ATPS) was synthesized by using 2-(dimethylamino)ethyl methacrylate, t-butyl methacrylate, and methyl methacrylate as monomers and 2,2'-azo-bis-isobutyronitrile as initiator. The P(ABC) could be recovered by adjusting isoelectric point (PI) to 8.4, and recovery at PI could reach 95%. ATPS was formed by 5% (w/w) P(ABC) and 10% (w/w) PEG20000. The partition coefficient K of lysozyme was 6.8, and the partition coefficient K of bovine serum albumin could reach 12.5 in the ATPS.

[Phase transfer catalyzed bioconversion of penicillin G to 6-APA by immobilized penicillin acylase in recyclable aqueous two-phase systems with light/pH sensitive copolymers].

Immobilized penicillin acylase was used for bioconversion of penicillin PG into 6-APA in aqueous two-phase systems consisting of a light-sensitive polymer PNBC and a pH-sensitive polymer PADB. Partition coefficients of 6-APA was found to be about 5.78 in the presence of 1% NaCl. Enzyme kinetics showed that the reaction reached equilibrium at roughly 7 h. The 6-APA mole yields were 85.3% (pH 7.8, 20 degrees C), with about 20% increment as compared with the reaction of single aqueous phase buffer. The partition coefficient of PG (Na) varied scarcely, while that of the product, 6-APA and phenylacetic acid (PA) significantly varied due to Donnan effect of the phase systems and hydrophobicity of the products. The variation of the partition coefficients of the products also affected the bioconversion yield of the products. In the aqueous two-phase systems, the substrate, PG, the products of 6-APA and PA were biased in the top phase, while immobilized penicillin acylase at completely partitioned at the bottom. The substrate and PG entered the bottom phase, where it was catalyzed into 6-APA and PA and entered the top phase. Inhibition of the substrate and products was removed to result in improvement of the product yield, and the immobilized enzyme showed higher efficiency than the immobilized cells and occupied smaller volume. Compared with the free enzyme, immobilized enzyme had greater stability, longer life-time, and was completely partitioned in the bottom phase and recycle. Bioconversion in two-phase systems using immobilized penicillin acylase showed outstanding advantage. The light-sensitive copolymer forming aqueous two-phase systems could be recovered by laser radiation at 488 nm or filtered 450 nm light, while pH-sensitive polymer PADB could be recovered at the isoelectric point (pH 4.1). The recovery of the two copolymers was between 95% and 99%.

Production of 6-aminopenicillanic acid in aqueous two-phase systems by recombinant Escherichia coli with intracellular penicillin acylase.

Bioconversion of penicillin G in PEG 20000/dextran T 70 aqueous two-phase systems was achieved using the recombinant Escherichia coli A56 (ppA22) with an intracellular penicillin acylase as catalyst. The best conversion conditions were attained for: 7% (w/v) substrate (penicillin G), enzyme activity in bottom phase 52 U ml(-1), pH 7.8, temperature 37 degrees C, reaction time 40 min. Five repeated batches could be performed in these conditions. Conversions ratios between 0.9-0.99 mol of 6-aminopenicillanic acid (6-APA) per mol of penicillin G, were obtained and volumetric productivity was 3.6-4.6 micromol min(-1) ml(-1). In addition the product 6-APA could be directly crystallized from the top phase with a purity of 96%.

Affinity Chromatography of Urokinase Using Cefazoline as a Ligand.

Sepharose 4B-based affinity adsorbent was prepared using cefazoline as a ligand, and epichlorohydrin as an activator. The density of the ligand in the affinity adsorbents was about 43 &mgr;mol/g wet gel. The optimal adsorption pH for urokinase was 6.0, and the optimal adsorption salt concentration was 1.0 mol/L NaCl. The optimal conditions of elution were 0.1 mol/L glycine buffer, pH 9.0, containing 0.5 mol/L NaCl. A crude urokinase with specific activity 500 u/mg protein was purified on an affinity chromatography column (1 cm x 12 cm), yielding a product of specific activity of 49 300 u/mg with 78% recovery and 98.6-fold purification.