Dosimetry of microbeam radiotherapy by flexible hydrogenated amorphous silicon detectors.

Detectors that can provide accurate dosimetry for microbeam radiation therapy (MRT) must possess intrinsic radiation hardness, a high dynamic range, and a micron-scale spatial resolution. In this work we characterize hydrogenated amorphous silicon detectors for MRT dosimetry, presenting a novel combination of flexible, ultra-thin and radiation-hard features. Two detectors are explored: an n-i-p planar diode (NIP) and an NIP with an additional charge selective layer (NIP+CSC). The sensitivity of the NIP+CSC detector was greater than the NIP detector for all measurement conditions. At 1 V and 0 kGy under the 3T Cu-Cu synchrotron broadbeam, the NIP+CSC detector sensitivity of (7.76 ± 0.01) pC/cGy outperformed the NIP detector sensitivity of (3.55 ± 0.23) pC/cGy by 219 %. The energy dependence of both detectors matches closely to the attenuation coefficient ratio of Silicon against Water. Radiation damage measurements of both detectors out to 40 kGy revealed a higher radiation tolerance in the NIP detector compared to the NIP+CSC (17.2 % and 33.5 % degradations, respectively). Percentage depth dose profiles matched the PTW microDiamond detector's performance to within ± 6 % for all beam filtrations except in 3T Al-Al due to energy dependence. The microbeam field profile was reconstructed with a high spatial resolution, returning microbeam widths and peak-to-peak distances of (51 ± 1) µm and (405 ± 5) µm, respectively. The peak-to-valley dose ratio was measured as a function of depth and agrees within error to the values obtained with the PTW microDiamond. X-ray beam induced charge mapping of the detector revealed minimal dose perturbations from extra-cameral materials. The detectors are comparable to commercially available dosimeters for quality assurance in MRT. With added benefits of being micron-sized and possessing a flexible water-equivalent substrate, these detectors are attractive candidates for quality assurance, in-vivo dosimetry and in-line beam monitoring for MRT and FLASH therapy. .

Increased concentrations of P2X7R in oligodendrocyte derived extracellular vesicles of Multiple sclerosis patients.

Activation of the purinergic receptor P2X7 (P2X7R) is believed to be deleterious in autoimmune diseases and it was hypothesized to play a role in the pathogenesis of MS. P2X7R is an ATP-gated non-selective cationic channel; its activation can be driven by high concentrations of ATP and leads to the generation of large, cytolytic conductance pores. P2X7R activation can also result in apoptosis as a consequence of the activation of the caspase cascade via P2X7R-dependent stimulation of the NLRP3 inflammasome. We measured P2X7R in oligodendrocyte derived extracellular vesicles (ODEVs) in MS patients and in healthy subjects. Sixty-eight MS patients (50 relapsing-remitting, RR-MS, 18 primary progressive, PP-MS) and 57 healthy controls (HC) were enrolled. ODEVs were enriched from serum by a double step immunoaffinity method using an anti OMGp (oligodendrocyte myelin glycoprotein) antibody. P2X7R concentration was measured in ODEVs lysates by ELISA. One-way Anova test showed that P2X7R in ODEVs is significantly higher in PP-MS (mean: 1742.89 pg/mL) compared both to RR-MS (mean: 1277.33 pg/mL) (p < 0.001) and HC (mean: 879.79 pg/mL) (p < 0.001). Comparison between RR-MS and HC was also statistically significant (p < 0.001). Pearson's correlations showed that P2RX7 in ODEVs was positively correlated with EDSS (p = 0.002, r = 0.38, 0.15-0.57 95% CI) and MSSS (p = 0.004, r = 0.34, 0.12-0.54 95% CI) scores, considering MS patients together (PP-MS + RR-MS) and with disease duration in PP-MS group (p = 0.02, r = 0.53, 0.09-0.80 95% CI). Results suggest that ODEVs-associated P2X7R levels could be a biomarker for MS.

Heterogeneous Integration of Acoustic Microextraction with an Optoelectronic Sensor on Glass for Nucleic Acid Testing.

Lab-on-a-chip systems (LOCs), characterized by their high sensitivity, low sample consumption, and portability, have significantly advanced the field of on-site testing. Despite the evolution of integrated LOCs from qualitative to quantitative analyses, on-chip full integration of sample preparation, purification, and multiplexed detection remains a challenge. Here, we propose a strategy for the heterogeneous integration of a set of complementary metal oxide semiconductor-compatible devices including acoustic resonator, thin-film resistors, and temperature/photosensors as a new type of LOC for nucleic acid testing (NAT). Programmed acoustic streaming-based particles and fluid manipulations largely simplify the nucleic acid extraction process including cell lysis, nucleic acid capture, and elution. The design of the acoustic microextraction module and extraction process was thoroughly studied. Benefitted by the microelectromechanical system approach, the conventional mechanical actions and complex flow control are avoided, which enables a compact hand-held NAT instrument without complicated peripherals. Validation experiments conducted on plasma-harboring mutations in the epidermal growth factor receptor (EGFR) gene confirmed the robustness of the system, achieving an impressive nucleic acid (NA) extraction efficiency of approximately 90% within 5 min and a limit of detection of the target NA in the plasma of 1 copy/µL.

EBV and multiple sclerosis: expression of LMP2A in MS patients.

Several evidences, including increased serum titers of Epstein-Barr virus (EBV)-specific antibodies and the presence of EBV DNA in brain of patients suggest a possible role of this virus in the pathogenesis of Multiple Sclerosis (MS), a chronic neurodegenerative disease with an unknown etiopathology. Aim of the present study is to verify if the expression of LMP2A and EBNA-1, two EBV genes, is altered in MS patients. EBV viral load, LMP2A and EBNA-1 gene expression and EBNA-1 antibodies titers were evaluated in blood of EBV-seropositive MS patients (n = 57; 31 relapsing remitting -RRMS- and 26 progressive -PMS-patients) and age- and sex-matched healthy controls (HC, n = 49). Results showed that EBNA-1 and VCA antibodies titers are significantly augmented in MS patients compared to HC (p < 0.05 for both antibodies); detection of EBV DNA was more frequent as well in MS patients compared to HC, although without reaching statistical significance. Regarding viral gene expression, LMP2A was significantly more frequently detected and more expressed in MS patients compared to HC (p < 0.005) whereas no differences were observed for EBNA-1. Considering patients alone, EBNA-1 was significantly more frequent in PMS compared to RRMS (p < 0.05), whereas no differences were observed for LMP2A. Increased expression of the LMP2A latency-associated gene in MS patients supports the hypothesis that EBV plays a role in disease etiopathology.

APHRODITE: A Compact Lab-on-Chip Biosensor for the Real-Time Analysis of Salivary Biomarkers in Space Missions.

One of the main challenges to be faced in deep space missions is to protect the health and ensure the maximum efficiency of the crew by preparing methods of prevention and in situ diagnosis. Indeed, the hostile environment causes important health problems, ranging from muscle atrophy, osteopenia, and immunological and metabolic alterations due to microgravity, to an increased risk of cancer caused by exposure to radiation. It is, therefore, necessary to provide new methods for the real-time measurement of biomarkers suitable for deepening our knowledge of the effects of space flight on the balance of the immune system and for allowing the monitoring of the astronaut's health during long-term missions. APHRODITE will enable human space exploration because it fills this void that affects both missions in LEO and future missions to the Moon and Mars. Its scientific objectives are the design, production, testing, and in-orbit demonstration of a compact, reusable, and reconfigurable system for performing the real-time analysis of oral fluid samples in manned space missions. In the frame of this project, a crew member onboard the ISS will employ APHRODITE to measure the selected target analytes, cortisol, and dehydroepiandrosterone sulfate (DHEA-S), in oral fluid, in four (plus one additional desired session) separate experiment sessions. The paper addresses the design of the main subsystems of the analytical device and the preliminary results obtained during the first implementations of the device subsystems and testing measurements on Earth. In particular, the system design and the experiment data output of the lab-on-chip photosensors and of the front-end readout electronics are reported in detail along with preliminary chemical tests for the duplex competitive CL-immunoassay for the simultaneous detection of cortisol and DHEA-S. Different applications also on Earth are envisaged for the APHRODITE device, as it will be suitable for point-of-care testing applications (e.g., emergency medicine, bioterrorism, diagnostics in developing countries, etc.).

Sensitive and Compact Evanescent-Waveguide Optical Detector for Sugar Sensing in Commercial Beverages.

This work presents a compact and sensitive refractive index sensor able to evaluate the concentration of an analyte in a sample. Its working principle leverages on the changes in the optical absorption features introduced by the sample itself on the evanescent waves of a light beam. The device's high compactness is achieved by embedding the sample-light interaction site and the detector in a 1 cm2 glass substrate, thanks to microelectronics technologies. High sensitivity is obtained by employing a low-noise p-i-n hydrogenated amorphous silicon junction, whose manufacture process requires only four UV lithographic steps on a glass substrate, thus ensuring low production costs. The system's capabilities are investigated by sensing the sugar content in three commercial beverages. Sensitivities of 32, 53 and 80 pA/% and limits of detection of 47, 29 and 18 ppm are achieved. The above performance is comparable with state-of-the-art results available in the literature, where more complex optical setups, expensive instrumentation and bulky devices are used.

Valorisation of Tuff and Brick Wastes by Alkali Activation for Historical Building Remediation.

Nowadays, the preservation and restoration of a historical building needs to be faced in accordance with a novel sensibility regarding the environment in order to preserve the building for future generations. In this context, the scientific community is focusing on novel and sustainable materials and techniques that allow for durability and mechanical performance as well as compatibility with the existing heritage. Alkali-activated materials represent a great challenge to the production of new materials, starting from the existing ones, with the goal of reducing consumption, emission of greenhouse gases and environmental impact. This study deals with the valorisation of waste materials coming from demolition and construction activities in the manufacture of geocomposites suitable for the restoration and conservation of historical heritage. In particular, waste from tuff sawing and brick grinding were used as raw materials, and then the geopolymeric samples produced were characterized based on a physical-chemical and mechanical point of view in order to investigate their performance and evaluate their suitability as materials for a historical building's recovery. The results showed that brick waste-based geocomposites were more compact than the tuff-based ones, as shown by the higher-density values and the lower values of open porosity and water absorption and as further confirmed by the trend of the mechanical performance. Moreover, experimental data showed that the physical and mechanical properties of both bricks and tuff waste-based geocomposites, even with different waste content, are compatible with existing building materials as well as traditional repairing products.

Vitamin D Receptor Gene Polymorphism Predicts the Outcome of Multidisciplinary Rehabilitation in Multiple Sclerosis Patients.

Better knowledge about the possible role of genetic factors in modulating the response to multiple sclerosis (MS) treatment, including rehabilitation, known to promote neural plasticity, could improve the standard of care for this disease. Vitamin D receptor (VDR) gene polymorphisms are associated with MS risk, probably because of the role played by vitamin D in regulating inflammatory and reparative processes. The aim of this study was to evaluate the association of the most important functional VDR SNPs (TaqI (T/C), ApaI (A/C), and FokI (C/T)) with functional outcome in MS patients undergoing multidisciplinary inpatient rehabilitation (MDR) treatment, in order to determine whether genetic profiling might be useful to identify subjects with a higher chance of recovery. To this end, 249 MS inpatients with a diagnosis of either progressive (pMS; n = 155) or relapsing remitting (RRMS; n = 94) disease who underwent MDR treatment (average duration = 5.1 weeks) were genotyped for VDR SNPs by real-time allelic discrimination. The rehabilitation outcome was assessed using the modified Barthel Index (mBI), Expanded Disability Status Scale (EDSS), and pain numerical rating scores (NRS) at the beginning and the end of MDR treatment. A positive correlation was observed in RRMS patients between the VDR TaqI major allele (TT) and mBI increase (i.e., better functional recovery), as assessed by the linear and logistic regression analysis adjusted for gender, age, disease duration, time of hospitalization, HLA-DRB1*15.01 positivity, and number of rehabilitative interventions (Beta = 6.35; p = 0.0002). The VDR-1 TaqI, ApaI, FokI: TCC haplotype was also associated with mBI increase in RRMS patients (Beta = 3.24; p = 0.007), whereas the VDR-2: CAC haplotype was correlated with a lower mBI increase (Beta = -2.18 p = 0.04) compared with the other haplotypes. VDR TaqI major allele (TT), as well as the VDR-1 TaqI, ApaI, FokI: TCC haplotype could be associated with a better rehabilitation outcome in RRMS patients.

Gold Nanoparticles-Functionalized Cotton as Promising Flexible and Green Substrate for Impedometric VOC Detection.

This work focuses on the possible application of gold nanoparticles on flexible cotton fabric as acetone- and ethanol-sensitive substrates by means of impedance measurements. Specifically, citrate- and polyvinylpyrrolidone (PVP)-functionalized gold nanoparticles (Au NPs) were synthesized using green and well-established procedures and deposited on cotton fabric. A complete structural and morphological characterization was conducted using UV-VIS and Fourier transform infrared (FT-IR) spectroscopy, atomic force microscopy (AFM), and scanning electron microscopy (SEM). A detailed dielectric characterization of the blank substrate revealed interfacial polarization effects related to both Au NPs and their specific surface functionalization. For instance, by entirely coating the cotton fabric (i.e., by creating a more insulating matrix), PVP was found to increase the sample resistance, i.e., to decrease the electrical interconnection of Au NPs with respect to citrate functionalized sample. However, it was observed that citrate functionalization provided a uniform distribution of Au NPs, which reduced their spacing and, therefore, facilitated electron transport. Regarding the detection of volatile organic compounds (VOCs), electrochemical impedance spectroscopy (EIS) measurements showed that hydrogen bonding and the resulting proton migration impedance are instrumental in distinguishing ethanol and acetone. Such findings can pave the way for the development of VOC sensors integrated into personal protective equipment and wearable telemedicine devices. This approach may be crucial for early disease diagnosis based on nanomaterials to attain low-cost/low-end and easy-to-use detectors of breath volatiles as disease markers.

Biomolecular Monitoring Tool Based on Lab-on-Chip for Virus Detection.

Lab-on-Chip (LoC) devices for performing real-time PCR are advantageous compared to standard equipment since these systems allow to conduct in-field quick analysis. The development of LoCs, where the components for performing the nucleic acid amplification are all integrated, can be an issue. In this work, we present a LoC-PCR device where thermalization, temperature control and detection elements are all integrated on a single glass substrate named System-on-Glass (SoG) obtained using metal thin-film deposition. By using a microwell plate optically coupled with the SoG, real-time reverse transcriptase PCR of RNA extracted from both a plant and human virus has been carried out in the developed LoC-PCR device. The limit of detection and time of analysis for the detection of the two viruses by using the LoC-PCR were compared with those achieved by standard equipment. The results showed that the two systems can detect the same concentration of RNA; however, the LoC-PCR performs the analysis in half of the time compared to the standard thermocycler, with the advantage of the portability, leading to a point-of-care device for several diagnostic applications.

New Materials and Technologies for Durability and Conservation of Building Heritage.

The increase in concrete structures' durability is a milestone to improve the sustainability of buildings and infrastructures. In order to ensure a prolonged service life, it is necessary to detect the deterioration of materials by means of monitoring systems aimed at evaluating not only the penetration of aggressive substances into concrete but also the corrosion of carbon-steel reinforcement. Therefore, proper data collection makes it possible to plan suitable restoration works which can be carried out with traditional or innovative techniques and materials. This work focuses on building heritage and it highlights the most recent findings for the conservation and restoration of reinforced concrete structures and masonry buildings.

AstroBio-CubeSat: A lab-in-space for chemiluminescence-based astrobiology experiments.

Space exploration is facing a new era in view of the planned missions to the Moon and Mars. The development and the in-flight validation of new technologies, including analytical and diagnostic platforms, is pivotal for exploring and inhabiting these extreme environments. In this context, biosensors and lab-on-chip devices can play an important role in many situations, such as the analysis of biological samples for assessing the impact of deep space conditions on man and other biological systems, environmental and food safety monitoring, and the search of molecular indicators of past or present life in extra-terrestrial environments. Small satellites such as CubeSats are nowadays increasingly exploited as fast and low-cost platforms for conducting in-flight technology validation. Herein, we report the development of a fully autonomous lab-on-chip platform for performing chemiluminescence-based bioassays in space. The device was designed to be hosted onboard the AstroBio CubeSat nanosatellite, with the aim of conducting its in-flight validation and evaluating the stability of (bio)molecules required for bioassays in a challenging radiation environment. An origami-like microfluidic paper-based analytical format allowed preloading all the reagents in the dried form on the paper substrate, thus simplifying device design and analytical protocols, facilitating autonomous assay execution, and enhancing the stability of reagents. The chosen approach should constitute the first step to implement a mature technology with the aim to conduct life science research in space (e.g., for evaluation the effect of deep space conditions on living organisms or searching molecular evidence of life) more easily and at lower cost than previously possible.

Myelin Basic Protein in Oligodendrocyte-Derived Extracellular Vesicles as a Diagnostic and Prognostic Biomarker in Multiple Sclerosis: A Pilot Study.

Approximately 15% of multiple sclerosis (MS) patients develop a progressive form of disease from onset; this condition (primary progressive-PP) MS is difficult to diagnose and treat, and is associated with a poor prognosis. Extracellular vesicles (EVs) of brain origin isolated from blood and their protein cargoes could function as a biomarker of pathological conditions. We verified whether MBP and MOG content in oligodendrocytes-derived EVs (ODEVs) could be biomarkers of MS and could help in the differential diagnosis of clinical MS phenotypes. A total of 136 individuals (7 clinically isolated syndrome (CIS), 18 PPMS, 49 relapsing remitting (RRMS)) and 70 matched healthy controls (HC) were enrolled. ODEVs were enriched from serum by immune-capture with anti-MOG antibody; MBP and MOG protein cargoes were measured by ELISA. MBP concentration in ODEVs was significantly increased in CIS (p < 0.001), RRMS (p < 0.001) and PPMS (p < 0.001) compared to HC and was correlated with disease severity measured by EDSS and MSSS. Notably, MBP concentration in ODEVs was also significantly augmented in PPMS compared to RRMS (p = 0.004) and CIS (p = 0.03). Logistic regression and ROC analyses confirmed these results. A minimally invasive blood test measuring the concentration of MBP in ODEVs is a promising tool that could facilitate MS diagnosis.

Two Single Nucleotide Polymorphisms in the Purinergic Receptor P2X7 Gene Are Associated with Disease Severity in Multiple Sclerosis.

Multiple sclerosis (MS) is a chronic autoimmune inflammatory disease of the central nervous system (CNS) that leads to progressive physical disability. Recent evidence has suggested that P2X7 receptor (P2X7R)-mediated purinergic signalling pathways play a role in MS-associated neuroinflammation, possibly contributing to disease pathogenesis. To evaluate possible associations between P2X7R polymorphisms and MS disease severity, we performed an association study of five non-synonymous SNPs coding variants of the P2X7R gene: rs1718119 Ala348Thr, rs2230911 Thr357Ser, rs2230912 Gln460Arg, rs3751143 Glu496Ala, and rs28360457 Arg307Gln, modulating P2X7R expression in 128 MS patients (relapsing remitting MS, RRMS: n = 94; secondary progressive, SPMS: n = 34). All patients were genotyped, and multiple sclerosis severity score (MSSS) was evaluated in every case; 189 healthy subjects were enrolled as well as controls. Results showed that P2X7R rs1718119(A) 348Thr and rs22390912(G) 464Arg, two SNPs of minor allele frequency (MAF) known to confer gain of function to the P2X7R protein, were associated with significantly higher MSSS in RRMS patients alone (SMRR (p < 0.001, p = 0.01, respectively)). Interestingly, two whole haplotypes resulted in having significant association with MSSS in these same patients. Thus: (1) the P2X7R-4 "ACGAG" haplotype, characterized by the co-presence of the rs1718119-rs2230912 AG MAF alleles, was associated with higher MSSS (Beta: 1.11 p = 0.04), and (2) the P2X7R-1 "GCAAG" complementary haplotype, which contains the rs1718119 and rs2230912 GA wild-type alleles, was more frequently carried by patients with lower MSSS and less severe disease (Beta: −1.54 p < 0.001). Although being preliminary and needing confirmation in an ampler cohort, these results suggest that 348Thr and 464Arg variants have a role as modulators of disease severity in RRMS patients.

Thin-Film-Based Multifunctional System for Optical Detection and Thermal Treatment of Biological Samples.

In this work, we present a multifunctional Lab-on-Chip (LoC) platform based on hydrogenated amorphous silicon sensors suitable for a wide range of application in the fields of biochemical and food quality control analysis. The proposed system includes a LoC fabricated on a 5 cm × 5 cm glass substrate and a set of electronic boards for controlling the LoC functionalities. The presented Lab-on-Chip comprises light and temperature sensors, a thin film resistor acting as a heating source, and an optional thin film interferential filter suitable for fluorescence analysis. The developed electronics allows to control the thin film heater, a light source for fluorescence and absorption measurements, and the photosensors to acquire luminescent signals. All these modules are enclosed in a black metal box ensuring the portability of the whole platform. System performances have been evaluated in terms of sensor optical performances and thermal control achievements. For optical sensors, we have found a minimum number of detectable photons of 8 × 104 s-1·cm-2 at room temperature, 1.6 × 106 s-1·cm-2 in presence of fluorescence excitation source, and 2.4 × 106 s-1·cm-2 at 90 °C. From a thermal management point of view, we have obtained heating and cooling rates both equal to 2.2 °C/s, and a temperature sensor sensitivity of about 3 mV/°C even in presence of light. The achieved performances demonstrate the possibility to simultaneously use all integrated sensors and actuators, making promising the presented platform for a wide range of application fields.

Assessing the consequences of prolonged usage of disposable face masks.

Due to the SARS-CoV-2 outbreak, wearing a disposable face mask has become a worldwide daily routine, not only for medical operators or specialized personnel, but also for common people. Notwithstanding the undeniable positive effect in reducing the risk of virus transmission, it is important to understand if a prolonged usage of the same face mask can have effectiveness on filtering capability and potential health consequences. To this aim, we present three investigations. A survey, carried out in central Italy, offers an overview of the distorted public awareness of face mask usage. A functional study shows how prolonged wearing leads to substantial drops in humid air filtration efficiency. Finally, a morphological analysis reports the proliferation of fungal or bacteria colonies inside an improperly used mask. Our study highlights therefore that wearing a face mask is really beneficial only if it is used correctly.

The Improvement of Durability of Reinforced Concretes for Sustainable Structures: A Review on Different Approaches.

The topic of sustainability of reinforced concrete structures is strictly related with their durability in aggressive environments. In particular, at equal environmental impact, the higher the durability of construction materials, the higher the sustainability. The present review deals with the possible strategies aimed at producing sustainable and durable reinforced concrete structures in different environments. It focuses on the design methodologies as well as the use of unconventional corrosion-resistant reinforcements, alternative binders to Portland cement, and innovative or traditional solutions for reinforced concrete protection and prevention against rebars corrosion such as corrosion inhibitors, coatings, self-healing techniques, and waterproofing aggregates. Analysis of the scientific literature highlights that there is no preferential way for the production of "green" concrete but that the sustainability of the building materials can only be achieved by implementing simultaneous multiple strategies aimed at reducing environmental impact and improving both durability and performances.

Mineralogical and Technological Characterization of Zeolites from Basin and Range as Pozzolanic Addition of Cement.

The present paper assesses petrographic, mineralogical, chemical, and technological features of different zeolitic tuff samples from various western USA districts of the Basin and Range Province containing mainly erionite, mordenite, clinoptilolite/heulandite and phillipsite. The aim of this characterization is to evaluate the pozzolanic activity of these samples according to European normative UNI-EN 196/5 (Fratini test) to program a possible use as addition for blended cements. Petrographic and mineralogical results show that the two phillipsite-bearing tuffs have a higher theoretical Cation Exchange Capacity (CEC) than the other samples; technological characterization shows a pozzolanic behavior for all the samples but higher for the tuff samples containing phillipsite, which shows a higher reactivity with CaO. All the samples could be thus advantageously employed for the preparation of blended cements, potentially reducing CO2 emissions by 70-90%.

Alterations of the miR-126-3p/POU2AF1/Spi-B Axis and JCPyV Reactivation in Multiple Sclerosis Patients Receiving Natalizumab.

Natalizumab (NTZ) can reactivate human polyomavirus John Cunningham polyomavirus (JCPyV) latent infection and lead to progressive multifocal leukoencephalopathy (PML). NTZ modulates the expression of microRNA-126-3p (miR-126-3p) and its target genes, Spi-B, POU2AF1, and vascular cell adhesion molecule-1 (VCAM-1); Spi-B protein binds the JCPyV regulatory region, initiating early gene transcription. This paper is aimed to evaluate the miR-126-3p and soluble (s)VCAM-1 concentration, Spi-B/POU2AF1 gene expression, and JCPyV activity in patients with multiple sclerosis (MS) before and during 2-years NTZ. Serum miR-126-3p and sVCAM-1 concentration was measured before NTZ and after 1, 12, and 24 months of treatment in 22 MS subjects, 1 patient who developed PML, and 29 healthy controls (HCs). The Spi-B and POU2AF1 expression in blood was analyzed at baseline and at month 24 in 13 patients with MS; results were clusterized based on JCPyV activity. miR-126-3p was significantly downregulated in MS before and during NTZ but was greatly increased in the PML patient. sVCAM-1 concentration was comparable in MS and HCs, and was reduced by NTZ in MS and PML. Spi-B/POU2AF1 expression was significantly increased in MS at baseline and was upregulated by NTZ, particularly in JCPyV-infected patients in whom JCPyV reactivation was detected. Taken together, the results suggest that the modulation of the miR-126-3p/POU2AF1/Spi-B axis associates with JCPyV activity in NTZ-treated patients with MS.

Split Aptamers Immobilized on Polymer Brushes Integrated in a Lab-on-Chip System Based on an Array of Amorphous Silicon Photosensors: A Novel Sensor Assay.

Innovative materials for the integration of aptamers in Lab-on-Chip systems are important for the development of miniaturized portable devices in the field of health-care and diagnostics. Herein we highlight a general method to tailor an aptamer sequence in two subunits that are randomly immobilized into a layer of polymer brushes grown on the internal surface of microfluidic channels, optically aligned with an array of amorphous silicon photosensors for the detection of fluorescence. Our approach relies on the use of split aptamer sequences maintaining their binding affinity to the target molecule. After binding the target molecule, the fragments, separately immobilized to the brush layer, form an assembled structure that in presence of a "light switching" complex [Ru(phen)2(dppz)]2+, emit a fluorescent signal detected by the photosensors positioned underneath. The fluorescent intensity is proportional to the concentration of the target molecule. As proof of principle, we selected fragments derived from an aptamer sequence with binding affinity towards ATP. Using this assay, a limit of detection down to 0.9 µM ATP has been achieved. The sensitivity is compared with an assay where the original aptamer sequence is used. The possibility to re-use both the aptamer assays for several times is demonstrated.