Detection of moisture ratio and carotenoid compounds in mamey (Pouteria sapota) fruit during dehydration process using spectroscopic techniques.

This work presents the study of the moisture ratio and carotenoid compounds in dried mamey (Pouteria sapota) using non-invasive spectroscopic techniques. The drying behavior of mamey at 64 °C by a homemade solar dryer is analyzed by fitting the experimental data to four different mathematical drying models. In addition, this result is compared with other drying techniques, namely by heat chamber with natural convection at temperatures of 50 °C and 60 °C. The results show that the Lewis model is the one that best fits the experimental moisture ratio curve of mamey. On the other hand, Near-Infrared and Terahertz spectroscopic techniques are used to estimate the moisture ratio, since water absorption is most sensitive at these frequencies. Fourier Transform Infrared-attenuated total reflectance and Raman spectroscopy are performed to detect the carotenoid compounds in dried mamey. This compound has important applications in the food industry and health benefits. To our knowledge, there are few studies on the dehydration of Pouteria sapota as well as its characterization using spectroscopic techniques for the detection of moisture ratio and carotenoid content; therefore, this study can be useful in agriculture and food sectors when detailed information about the cited parameters is needed.

Two-Photon Excitation Spectroscopy of Silicon Quantum Dots and Ramifications for Bio-Imaging.

Two-photon excitation in the near-infrared (NIR) of colloidal nanocrystalline silicon quantum dots (nc-SiQDs) with photoluminescence also in the NIR has potential opportunities in the field of deep biological imaging. Spectra of the degenerate two-photon absorption (2PA) cross section of colloidal nc-SiQDs are measured using two-photon excitation over a spectral range 1.46 < ℏω < 1.91 eV (wavelength 850 > λ > 650 nm) above the two-photon band gap Eg(QD)/2, and at a representative photon energy ℏω = 0.99 eV (λ = 1250 nm) below this gap. Two-photon excited photoluminescence (2PE-PL) spectra of nc-SiQDs with diameters d = 1.8 ± 0.2 nm and d = 2.3 ± 0.3 nm, each passivated with 1-dodecene and dispersed in toluene, are calibrated in strength against 2PE-PL from a known concentration of Rhodamine B dye in methanol. The 2PA cross section is observed to be smaller for the smaller diameter nanocrystals, and the onset of 2PA is observed to be blue shifted from the two-photon indirect band gap of bulk Si, as expected for quantum confinement of excitons. The efficiencies of nc-SiQDs for bioimaging using 2PE-PL are simulated in various biological tissues and compared to efficiencies of other quantum dots and molecular fluorophores and found to be comparable or superior at greater depths.

Imaging and SERS Study of the Au Nanoparticles Interaction with HPV and Carcinogenic Cervical Tissues.

In this work, gold NPs were prepared by the Turkevich method, and their interaction with HPV and cancerous cervical tissues were studied by scanning electron microscopy, energy-dispersive x-ray spectroscopy, confocal and multiphoton microscopy and SERS. The SEM images confirmed the presence and localization of the gold NPs inside of the two kinds of tissues. The light absorption of the gold NPs was at 520 nm. However, it was possible to obtain two-photon imaging (red emission region) of the gold NPs inside of the tissue, exciting the samples at 900 nm, observing the morphology of the tissues. The infrared absorption was probably due to the aggregation of gold NPs inside the tissues. Therefore, through the interaction of gold nanoparticles with the HPV and cancerous cervical tissues, a surface enhanced Raman spectroscopy (SERS) was obtained. As preliminary studies, having an average of 1000 Raman spectra per tissue, SERS signals showed changes between the HPV-infected and the carcinogenic tissues; these spectral signatures occurred mainly in the DNA bands, potentially offering a tool for the rapid screening of cancer.

Post-synthesis nanostructuration of BSA-Capsaicin nanoparticles generated by sucrose excipient.

In the pharmaceutical industry nano-hydrocolloid systems frequently coalesce or present nanoparticle aggregation after a long storage periods. Besides, the lyophilization process used to dry nanoparticles (NPs) produces loss of their original properties after dispersion. In this work we evaluated the effect on morphology and physicochemical properties of different protective excipients during drying of bovine serum albumin (BSA) NPs loaded with different concentrations of capsaicin. Capsaicin concentrations of 0, 812, 1625, 2437, and 3250 µg mL-1 were used; subsequently, NPs were dried with deionized water (DW), NaCl (DN), sucrose (DS), and not dried (ND). We found that ND, DW, and DN treatments showed a negative effect on the NPs properties; while, DS reduced the aggregation and produced the formation of isolated nanoparticles at higher concentrations of capsaicin (3250 µg mL-1), improving their circular shape, morphometrical parameters, and ζ-potential. The stability of the BSA-capsaicin NPs was associated to complex capsaicin/amino acid/water, in which GLY/GLN, ALA/HIS, ARG, THR, TYR, and Iso/CYS amino acids are involved in the restructuration of capsaicin molecules into the surface of nanoparticles during the drying process. The secondary nanostructuration in the post-synthesis stage can improve the molecular stability of the particles and the capacity of entrapping hydrophobic drugs, like capsaicin.

Generation of BSA-capsaicin Nanoparticles and Their Hormesis Effect on the Rhodotorula mucilaginosa Yeast.

Capsaicin is a chemical compound found in pungent chili peppers (Capsicum spp.). In biotechnology, capsaicin has been proposed as a pathogen control; however, its low solubility in water and high instability limits its uses. The aim of this work was to study the effect of high concentrations of capsaicin on the synthesis of nanoparticles and to evaluate their inhibitory effect on the growth of Rhodotorula mucilaginosa yeast. Bovine serum albumin (BSA)-capsaicin nanoparticles were formulated at 0, 16.2, 32.5, 48.7 and 65.0 µg of capsaicin per mg of BSA. Nanoparticle properties were evaluated and they were added to cultures of R. mucilaginosa to quantify their effect on cell viability. We found that increased capsaicin levels caused several changes to the physicochemical parameters, probably due to changes in the hydrophobicity sites of the albumin during the nanostructuration. The administration of nanoparticles to cultures of R. mucilaginosa produced a maximal viability with nanoparticles at 16.2 µg/mg; on the contrary, nanoparticles at 65.0 µg/mg caused maximal cell death. R. mucilaginosa cells displayed a hormesis effect in response to the nanoparticle dose concentration. The nanoparticles showed different responses during the uptake process, probably as a consequence of the nanostructural properties of capsaicin in the BSA molecules.

Effect of varying the crosslinking degree of a pericardial implant with oligourethane on the repair of a rat full-thickness abdominal wall defect.

The stability and bioactivity of biologic implants rely mainly on the control of the crosslinking process of collagen. However, the most common methods have no control on the crosslinking degree producing it excessively. This study outlines the role of crosslinking of collagen-based implants with oligourethane on the host response following reconstruction of a rat full-thickness abdominal wall defect. We decellularized and crosslinked bovine pericardial tissue to achieve two crosslinking degrees. For the decellularized implants, named as non-crosslinked (N-CL), the collagen-amines were 0.42 ± 0.02 mmol/mg. Crosslinking by the oligourethane reduced the primary amine concentration to 0.28 ± 0.01 and 0.19 ± 0.01 mmol/mg; these values were classified as low (∼30%, L-CL) and medium crosslinking (∼50%, M-CL), respectively. By imaging the implants using second harmonic generation microscopy, we observed undulated bundles of collagen fibers organized in multi-directed layers localized in N-CL and L-CL samples. Post-implantation, a negligible change in the organization of collagen fibers in the crosslinked implants was observed, suggesting that the in vivo biodegradation was delayed. An enlargement of the implant area was also observed, without rupture, in all three (N-CL, L-CL, M-CL) materials, whereas adhesion to the omentum, but not to the bowel, was observed. The number of blood vessels after 90-day implantation in N-CL and L-CL was 13 ± 1 and 12 ± 1 per field, respectively, while the number significantly decreased to 2 ± 1 in M-CL. The results suggest that the controlled degree of crosslinking in oligourethane-modified biologic implants can be used as a strategy to balance biodegradation and remodeling in surgical repair of soft tissues.

Design of Silica-Oligourethane-Collagen Membranes for Inflammatory Response Modulation: Characterization and Polarization of a Macrophage Cell Line.

The polarization of macrophages M0 to M1 or M2 using molecules embedded in matrices and hydrogels is an active field of study. The design of biomaterials capable of promoting polarization has become a paramount need nowadays, since in the healing process macrophages M1 and M2 modulate the inflammatory response. In this work, several immunocytochemistry and ELISA tests strongly suggest the achievement of polarization using collagen-based membranes crosslinked with tri-functionalized oligourethanes and coated with silica. Measuring the amount of TGF-ß1 secreted to culture media by macrophages growth on these materials, and quantifying the macrophage morphology, it is proved that it is possible to stimulate the anti-inflammatory pathway toward M2, having measurements with p ≤ 0.05 of statistical significance between the control and the collagen-based membranes. Furthermore, some physicochemical characteristics of the hybrid materials are tested envisaging future applications: collagenase degradation resistance, water uptake, collagen fiber diameter, and deformation resistance are increased for all the crosslinked biomaterials. It is considered that the biological and physicochemical properties make the material suitable for the modulation of the inflammatory response in the chronic wounds and promising for in vivo studies.

Improving the Optoelectronic Properties of Mesoporous TiO2 by Cobalt Doping for High-Performance Hysteresis-free Perovskite Solar Cells.

We for the first time report the incorporation of cobalt into a mesoporous TiO2 electrode for application in perovskite solar cells (PSCs). The Co-doped PSC exhibits excellent optoelectronic properties; we explain the improvements by passivation of electronic trap or sub-band-gap states arising due to the oxygen vacancies in pristine TiO2, enabling faster electron transport and collection. A simple postannealing treatment is used to prepare the cobalt-doped mesoporous electrode; UV-visible spectroscopy, X-ray photoemission spectroscopy, space charge-limited current, photoluminescence, and electrochemical impedance measurements confirm the incorporation of cobalt, enhanced conductivity, and the passivation effect induced in the TiO2. An optimized doping concentration of 0.3 mol % results in the maximum power conversion efficiency of 18.16%, 21.7% higher than that of a similar cell with an undoped TiO2 electrode. Also, the device shows negligible hysteresis and higher stability, retaining 80.54% of the initial efficiency after 200 h.

Interaction of TGA@CdTe Quantum Dots with an Extracellular Matrix of Haematococcus pluvialis Microalgae Detected Using Surface-Enhanced Raman Spectroscopy (SERS).

The present study reports the localization and interaction of thioglycolic acid (TGA) capped CdTe quantum dots (TGA@CdTe QDs) within the extracellular matrix (ECM) of Haematococcus pluvialis (Chlorophyceae) microalgae (HPM) after an incubation period of 5 min. Changes in the Raman spectrum of HPM induced by the adsorption of the TGA@CdTe QDs are successfully found by using naked gold anisotropic structures as nano-sensors for surface-enhanced Raman scattering (SERS effect). Raman spectroscopy results show that TGA@CdTe QDs interact with the biomolecules present in the ECM. Sample preparation and characterization by complementary techniques such as confocal and electron microscopy are also used to confirm the presence and localization of the nanoparticles in the algae. This research shows new evidence on early accumulation of QDs in plant cells and would further improve our understanding about their environmental impact.

Light Emission Properties of a Cross-Conjugated Fluorene Polymer: Demonstration of Its Use in Electro-Luminescence and Lasing Devices.

Light emission properties of a fluorene cross-conjugated polymer (PF⁻1) based on the monomer 4,7-bis[2-(9,9-dimethyl)fluorenyl] benzo[1,2,5]thiadiazole are reported. This polymer exhibits solubility at high concentrations, good processability into thin solid films of good quality and a broad emission band with a fluorescence quantum yield of approximately 1. Based on these features, in this paper we implemented the use of PF⁻1 as an active layer in polymer light-emitting diodes (PLEDs) and as a laser gain medium in solution. To get insight on the conducting properties of PF⁻1, two different electron injectors, poly [(9,9-bis(3'-(N,N-dimethylamino) propyl)-2,7-fluorene)-alt-2,7-(9,9⁻dioctylfluorene)] (PFN) and lithium fluoride (LiF), were used in a simple PLED architecture. PLEDs with the PFN film were found to exhibit better performance with a maximum luminous efficiency of 40 cd/A, a turn-on voltage (Von) of approximately 4.5 V and a luminance maximum of 878 cd/m² at 5.5 V, with a current density of 20 A/m². For the lasing properties of PF⁻1, we found a lasing threshold of around 75 µJ and a tunability of 20 nm. These values are comparable with those of rhodamine 6G, a well-known laser dye.

Optimizing the fluorescent yield in two-photon laser scanning microscopy with dispersion compensation.

A challenge for nonlinear imaging in living tissue is to maximize the total fluorescent yield from each fluorophore. We investigated the emission rates of three fluorophores-rhodamine B, a red fluorescent protein, and CdSe quantum dots-while manipulating the phase of the laser excitation pulse at the focus. In all cases a transform-limited pulse maximized the total yield to insure the highest signal-to-noise ratio. Further, we find evidence of fluorescence antibleaching in quantum dot samples.

Invited review article: Imaging techniques for harmonic and multiphoton absorption fluorescence microscopy.

We review the current state of multiphoton microscopy. In particular, the requirements and limitations associated with high-speed multiphoton imaging are considered. A description of the different scanning technologies such as line scan, multifoci approaches, multidepth microscopy, and novel detection techniques is given. The main nonlinear optical contrast mechanisms employed in microscopy are reviewed, namely, multiphoton excitation fluorescence, second harmonic generation, and third harmonic generation. Techniques for optimizing these nonlinear mechanisms through a careful measurement of the spatial and temporal characteristics of the focal volume are discussed, and a brief summary of photobleaching effects is provided. Finally, we consider three new applications of multiphoton microscopy: nonlinear imaging in microfluidics as applied to chemical analysis and the use of two-photon absorption and self-phase modulation as contrast mechanisms applied to imaging problems in the medical sciences.

High-resolution mosaic imaging with multifocal, multiphoton photon-counting microscopy.

High-resolution mosaic imaging is performed for the first time to our knowledge with a multifocal, multiphoton, photon-counting imaging system. We present a novel design consisting of a home-built femtosecond Yb-doped KGdWO(4) laser with an optical multiplexer, which is coupled with a commercial Olympus IX-71 microscope frame. Photon counting is performed using single-element detectors and an inexpensive electronic demultiplexer and counters.

Advancing multifocal nonlinear microscopy: development and application of a novel multibeam Yb:KGd(WO4)2 oscillator.

We present a novel Yb:KGd(WO(4))(2) oscillator design that generates six beams of temporally delayed, 253 fs, 11 nJ pulses. This allows multifocal nonlinear microscopy to be performed without the need for complicated optical multiplexers. We demonstrate our design with twelve simultaneously acquired two-photon, second-harmonic and/or third-harmonic images generated from six laterally separated foci.

Simultaneous multifocal, multiphoton, photon counting microscopy.

We demonstrate a novel multifocal, multiphoton microscope that is capable of simultaneous dynamic imaging of multiple focal planes. We show for the first time that multimodal, multiphoton images excited with orthogonal polarizations can be acquired simultaneously in both the transmission and epi directions.