In vitro evaluation of granules obtained from 3D sphene scaffolds and bovine bone grafts: chemical and biological assays.

Sphene is an innovative bone graft material. The aim of this study was to investigate and compare the physicochemical and biological properties of Bio-Oss® (BO) and in-lab synthesized and processed sphene granules. BO granules of 1000-2000 µm (BO-L), 250-1000 µm (BO-S) and 100-200 µm (BO-p) for derived granules, and corresponding groups of sphene granules obtained from 3D printed blocks (SB-L, SB-S, SB-p) and foams (SF-L, SF-S and SF-p) were investigated. The following analyses were conducted: morphological analysis, specific surface area and porosity, inductively coupled plasma mass spectrometry (ICP-MS), cytotoxicity assay, Alizarin staining, bone-related gene expression, osteoblast migration and proliferation assays. All pulverized granules exhibited a similar morphology and SF-S resembled natural bone. Sphene-derived granules showed absence of micro- and mesopores and a low specific surface area. ICP-MS revealed a tendency for absorption of Ca and P for all BO samples, while sphene granules demonstrated a release of Ca. No cellular cytotoxicity was detected and osteoblastic phenotype in primary cells was observed, with significantly increased values for SF-L, SF-S, BO-L and BO-p. Further investigations are needed before clinical use can be considered.

Novel flexible and conformable composite neutron scintillator based on fully enriched lithium tetraborate.

Thermal neutron detection is a key subject for nuclear physics research and also in a wide variety of applications from homeland security to nuclear medicine. In this work, it is proposed a novel flexible and conformable composite thermal neutron scintillator based on a fully enriched Lithium Tetraborate preparation ([Formula: see text]Li[Formula: see text]B[Formula: see text]O[Formula: see text]) combined with a phosphorescent inorganic scintillator powder (ZnS:Ag), and is then distributed into a polydimethylsiloxane matrix. The proposed scintillator shows a good neutron detection efficiency (max. [Formula: see text] 57% with respect to the commercial EJ-420), an average light output of [Formula: see text] 9000 ph/neutron-capture, a remarkable insensitivity to [Formula: see text]-rays (Gamma Rejection Ratio <10[Formula: see text]), and an extraordinary flexibility, so as to reach extremely small curvature radii, down to 1.5 mm, with no signs of cracking or tearing. Its characteristics make it suitable to be employed in scenarios where non-standard geometries are needed, for example, to optimize the detector performance and/or maximize the detection efficiency. Finally, the response of a hybrid detector made of a plastic scintillator, wrapped with the proposed scintillator, coupled to a silicon photomultiplier array is described, and the excellent discrimination between [Formula: see text]-rays, fast and thermal neutrons resulting from data processing is demonstrated.

Nanocomposite-parylene C thin films with high dielectric constant and low losses for future organic electronic devices.

Nanocomposite-parylene C (NCPC) thin films were deposited with a new technique based on the combination of chemical vapor deposition (CVD) for parylene C deposition and RF-magnetron sputtering for silver deposition. This method yields good dispersion of Ag-containing nanoparticles inside the parylene C polymer matrix. Film composition and structure were studied by using several techniques. It was found that the plasma generated by the RF-magnetron reactor modifies the film density as well as the degree of crystallinity and the size of parylene C crystallites. Moreover, silver is incorporated in the parylene matrix as an oxide phase. The average size of the Ag oxide nanoparticles is lower than 20 nm and influences the roughness of the NCPC films. Samples with various contents and sizes of silver-oxide nanoparticles were investigated by broadband dielectric spectroscopy (BDS) in view of their final application. It was found that both the content and the size of the nanoparticles influence the value of the dielectric constant and the frequency-dependence of the permittivity. In particular, ß-relaxation is affected by the addition of nanoparticles as well as the dissipation factor, which is even improved. A dielectric constant of 5 ± 1 with a dissipation factor of less than 0.045 in the range from 0.1 Hz to 1 MHz is obtained for a 2.7 µm thick NCPC with 3.8% Ag content. This study provides guidance for future NCPC materials for insulating gates in organic field-effect transistors (OFETs) and advanced electronic applications.

In-house cyclotron production of high-purity Tc-99m and Tc-99m radiopharmaceuticals.

In the last years, the technology for producing the important medical radionuclide technetium-99m by cyclotrons has become sufficiently mature to justify its introduction as an alternative source of the starting precursor [99mTc][TcO4]- ubiquitously employed for the production of 99mTc-radiopharmaceuticals in hospitals. These technologies make use almost exclusively of the nuclear reaction 100Mo(p,2n)99mTc that allows direct production of Tc-99m. In this study, it is conjectured that this alternative production route will not replace the current supply chain based on the distribution of 99Mo/99mTc generators, but could become a convenient emergency source of Tc-99m only for in-house hospitals equipped with a conventional, low-energy, medical cyclotron. On this ground, an outline of the essential steps that should be implemented for setting up a hospital radiopharmacy aimed at the occasional production of Tc-99m by a small cyclotron is discussed. These include (1) target production, (2) irradiation conditions, (3) separation/purification procedures, (4) terminal sterilization, (5) quality control, and (6) Mo-100 recovery. To address these issues, a comprehensive technology for cyclotron-production of Tc-99m, developed at the Legnaro National Laboratories of the Italian National Institute of Nuclear Physics (LNL-INFN), will be used as a reference example.

Deposition and characterization of luminescent Eu(tta)3phen-doped parylene-based thin-film materials.

Herein, novel host-guest films produced by coarse vacuum cosublimation of the parylene C dimer and Eu(tta)3phen are prepared and studied. Eu(tta)3phen sublimation at different temperatures allows films with different concentrations of the Eu complex to be obtained. The films are characterized by Rutherford backscattering spectrometry (RBS), FTIR spectroscopy, X-ray diffraction (XRD), atomic force microscopy (AFM), and UV/Vis absorption and emission spectroscopy. RBS, FTIR, and XRD reveal the incorporation of Eu(tta)3phen into the parylene matrix. AFM evidences the very flat film surface, which is particularly advantageous for optical applications. UV/Vis absorption and emission analyses confirm that the optical properties of Eu(tta)3phen are preserved in the deposited films. Fluorescence measurements evidence the occurrence of an energy-transfer process between parylene and Eu(tta)3phen, and this results in an increase in the light emitted by the Eu complex that is as much as five times higher than that emitted by Eu(tta)3phen alone.