Second Life for Plastic Fibre Waste Difficult to Recover: Partial Replacement of the Binder in Asphalt Concrete Mixtures by Dry Incorporation.

In previous studies, different additives and modifiers have been studied to improve the properties of asphalt concrete mixtures, whose main failures are plastic deformation and cracking. In this research, the improvement of the properties of asphalt concrete mixtures were investigated by introducing residual plastics as a substitute for virgin bitumen, which improves the sustainability of the mixtures. Furthermore, the results obtained from these new mixtures were compared with a mixture designed with polymer-modified bitumen (PMB). Ten experimental designs were tested with three types of waste fibre plastics from a municipal solid waste treatment plant and two percentages of bitumen replacement (15% and 25%). The experimental testing plan included air void characterization, moisture sensitivity, stiffness and fatigue resistance, among others. An increase of approximately 5% in voids could be observed when introducing the plastic material and therefore some tests were carried out to over-compact the specimens. The results showed an improvement in the mechanical performance of the experimental mixtures, highlighting the resistance against plastic deformations, which even reached similar values to the mixtures made with PMB.

Assessment of the environmental acceptability of potential artificial reef materials using two ecotoxicity tests: Luminescent bacteria and sea urchin embryogenesis.

Ecotoxicological analysis of construction products is a relatively unexplored area at international level. Aquatic toxicity tests on construction products has been recommended recently for freshwater environment. However, the biological effects of alternative materials on marine ecosystem are still not considered. In this study, the main aim was to assess the environmental impact of alternative mortars proposed as artificial reefs (ARs) materials. The ARs specimens were developed by 3D printing, based on cement and geopolymer mortars using recycled sands of glass and seashells. For this purpose, a leaching test and two different toxicity bioassays, luminosity reduction of marine bacteria Vibrio fischeri (Microtox®) and the success of embryo-larval development of sea-urchin Paracentrotus lividus, were conducted. From the leaching results it should be noted that the mobility of all trace elements considered in both, raw materials and mortars, meet the inert landfill limits, except As, Mo, Se or Sb in the leachates geopolymer mortars. However, the results obtained from the both bioassays show low environmental acceptability for those mortars containing shell sand, probably due to the degradation of the organic matter adhered to the shells. On the other hand, cement mortars obtain better results than geopolymer mortars, regardless of the aggregate used, showing certain consistency with the leaching behaviour, since they present the lowest mobility of trace chemical elements. Therefore, the results supporting the environmental acceptability of its potential use as alternative materials in the production of ARs.

Effect of Different Types of "Dry Way" Additions in Porous Asphalt Mixtures.

Polymers are widely used to improve the mechanical performance of asphalt mixtures. Among them, styrene butadiene styrene (SBS) is the most commonly used, especially in the wet modification of virgin bitumen. This method, which is extensively utilized, has several advantages, but also some disadvantages, concerning its performance (such as the risk of instability or a lack of homogeneity) and logistical management (such as the need for special equipment, the transport of materials, and the dependence on the refinery that modifies the bitumen). This paper analyses the use of the most conventional types of polymers (two types of SBS, one type of BS, and rubber from end-of-life tires), dry added, as an alternative method. They have been used in porous asphalt mixtures. This type of bituminous mixture is usually designed with commercial polymer-modified bitumen, due to the mechanical requirements, and it is very sensitive to the properties of the binder used. The mechanical behavior of experimental porous asphalt mixtures has been significantly improved, especially in the case of SBS, although the performance did not reach that of commercial polymer-modified bitumen. The results have shown that the dry method is a suitable and feasible option to manufacture modified mixtures, especially considering its advantages, from a logistical viewpoint, in comparison with the wet method.

Laboratory Characterization of Porous Asphalt Mixtures with Aramid Fibers.

Recent studies have shown that fibers improve the performance of porous asphalt mixtures. In this study, the influence of four different fibers, (a) regular aramid fiber (RegAR), (b) aramid fiber with latex coating (ARLat), (c) aramid fiber with polyurethane coating (ARPoly), (d) aramid fiber of length 12 mm (AR12) was evaluated on abrasion resistance and toughness of the mixtures. The functional performance was estimated using permeability tests and the mechanical performance was evaluated using the Cantabro test and indirect tensile strength tests. The parameters such as fracture energy, post cracking energy, and toughness were obtained through stress-strain plots. Based on the analysis of results, it was concluded that the addition of ARLat fibers enhanced the abrasion resistance of the mixtures. In terms of ITS, ARPoly and RegAR have positively influenced mixtures under dry conditions. However, the mixtures with all aramid fibers were found to have adverse effects on the ITS under wet conditions and energy parameters of porous asphalt mixtures with the traditional percentages of bitumen in the mixture used in Spain (i.e., approximately 4.5%).

Effect of Synthetic Fibers and Hydrated Lime in Porous Asphalt Mixture Using Multi-Criteria Decision-Making Techniques.

Porous asphalt is a type of mixture characterized by having high air void percentages that offers multiple benefits when used in wearing courses in terms of driving safety, water flow management, and noise reduction. However, the durability of porous asphalt (PA) mixtures is significantly shorter when compared to dense-graded asphalt mixtures. This study investigated the impact of polyolefin-aramid fibers and hydrated lime in the functional and mechanical performance of porous asphalt mixtures. A parametric study based on the concept of design of experiments was carried out through the Taguchi methodology. Accordingly, an experimental design was conducted based on the L18 full factorial orthogonal array. Three control factors-fiber content, binder content, and filler type-were included at various levels, and multiple responses including total air voids, interconnected air voids, particle loss in dry conditions, particle loss in wet conditions, and binder drainage were assessed experimentally. Signal-to-noise ratios were calculated to determine the optimal solution levels for each control factor for the multiple responses. In the second phase of the research, multi-criteria decision-making techniques-namely, criteria importance through inter-criteria correlation and weighted aggregated sum product assessment-were used to transform the multiple-response optimization problem into a single-unique optimization problem and to elaborate a preference ranking among all the mixture designs. The most significant levels for acquiring the optimum overall response value were found to be 0.05% for fiber content and 5.00% for binder content and mixed filler with hydrated lime.

Multi-Response Optimization of Porous Asphalt Mixtures Reinforced with Aramid and Polyolefin Fibers Employing the CRITIC-TOPSIS Based on Taguchi Methodology.

For the optimum design of a Porous Asphalt (PA) mixture, different requirements in terms of functionality and durability have to be fulfilled. In this research, the influence of different control factors such as binder type, fiber content, and binder content were statistically investigated in terms of multiple responses such as total air voids, interconnected air voids, particle loss in dry conditions, particle loss in wet conditions, and binder drainage. The experiments were conducted based on a Taguchi L18 orthogonal array. The best parametric combination per each response was analyzed through signal to noise ratio values. Multiple regression models were employed to predict the responses of the experiments. As more than one response is obtained, a multi-objective optimization was performed by employing Criteria Importance through Criteria Inter-Correlation (CRITIC) and Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) methodologies. The weights for the selection of the functional and mechanical performance criteria were derived from the CRITIC approach, whereas the ranking of the different experiments was obtained through the TOPSIS technique. According to the CRITIC-TOPSIS based Taguchi methodology, the optimal multiple-response was obtained for a polymer modified binder (PMB) with fiber and binder contents of 0.15% and 5.0%, respectively. In addition, good results were obtained when using a conventional 50/70 penetration grade binder with a 5.0% binder content and 0.05% fiber content.

Incorporation of Additives and Fibers in Porous Asphalt Mixtures: A Review.

Despite the numerous benefits for preserving the hydrological cycle, permeable pavement systems (PPSs) found their major application in parking spots and for light traffic scenarios due to their limited durability and strength. To make the PPSs suitable for heavy traffic conditions without significant distresses, research is shifting toward the adoption of novel binders and additives for designing multifunctional porous asphalt mixtures which make up the surface course of PPSs. Certain additives are well known for enhancing the durability of dense graded asphalt mixtures and improving fatigue and rutting resistance. However, the studies on the influence of additives on abrasion resistance and binder draindown, which are the common problems in porous asphalt mixtures (PAMs), are still not well established. This paper summarizes best practices performed on PAMs and recommends possible future research directions for its improvement. Particular emphasis is placed on strength and resilience of PAMs by incorporating additives like nanosilica, crumb rubber, warm-mix additives, fibers (such as cellulose, glass, steel, and synthetic fibers), and some eco-friendly materials. It was found that different additives seem to have different effects on the properties of PAMs. Moreover, the combination of additives has synergistic benefits for the performance of PAMs, especially in urban pavements.

Proposal of a New Porous Concrete Dosage Methodology for Pavements.

Although porous concrete pavement design methods are mainly focused on maintaining high permeability rates in order to improve their ability to manage stormwater runoff, the mixture strength is paramount for its durability and service life. This paper proposes a new mixture design method for porous concrete, named PCD (porous concrete design), derived from the ACI 522R-10 and ACI 211.3R-02 standards. The aim is to improve mechanical strength in porous concrete mixtures, while ensuring enough permeability for its use in urban roads. With PCD methodology it is possible to obtain mechanical strengths 30% higher than those produced with ACI methodologies, while maintaining permeability rates close to 2 cm/s, lower than those obtained with ACI methods but still enough to manage extreme storm events. Finally, with the analytical Hierarchy Process (AHP) multi-criteria decision-making methodology and also bearing in mind safety variables, the best porous concrete mixtures are the ones produced with PCD methodology.

Self-Healing Capacity of Asphalt Mixtures Including By-Products Both as Aggregates and Heating Inductors.

Major advances have been achieved in the field of self-healing by magnetic induction in which the addition of metallic particles into asphalt mixtures enables repairing their own cracks. This technology has already been proven to increase the life expectancy of roads. Nevertheless, its higher costs in comparison with conventional maintenance caused by the price of virgin metallic particles still makes it unattractive for investment. This research aimed at making this process economically accessible as well as environmentally efficient. To this end, an intense search for suitable industrial by-products to substitute both the virgin metal particles and the natural aggregates forming asphalt mixtures was conducted. The set of by-products used included sand blasting wastes, stainless shot wastes, and polished wastes as metallic particles and other inert by-products as aggregates. The results demonstrated that the by-products were adequately heated, which leads to satisfactory healing ratios in comparison with the reference mixture.

Water quality and quantity assessment of pervious pavements performance in experimental car park areas.

Pervious pavements have become one of the most used sustainable urban drainage system (SUDS) techniques in car parks. This research paper presents the results of monitoring water quality from several experimental car park areas designed and constructed in Spain with bays made of interlocking concrete block pavement, porous asphalt, polymer-modified porous concrete and reinforced grass with plastic and concrete cells. Moreover, two different sub-base materials were used (limestone aggregates and basic oxygen furnace slag). This study therefore encompasses the majority of the materials used as permeable surfaces and sub-base layers all over the world. Effluent from the test bays was monitored for dissolved oxygen, pH, electric conductivity, total suspended solids, turbidity and total petroleum hydrocarbons in order to analyze the behaviour shown by each combination of surface and sub-base materials. In addition, permeability tests were undertaken in all car parks using the 'Laboratorio Caminos Santander' permeameter and the Cantabrian Portable Infiltrometer. All results are presented together with the influence of surface and sub-base materials on water quality indicators using bivariate correlation statistical analysis at a confidence level of 95%. The polymer-modified porous concrete surface course in combination with limestone aggregate sub-base presented the best performance.

Laboratory analysis of the infiltration capacity of interlocking concrete block pavements in car parks.

Interlocking concrete block pavements (ICBPs) have been widely used in car parks to reduce runoff. Researches have demonstrated that clogging is the most influential factor in the reduction of the infiltration capacity of this type of permeable pavement. Nevertheless, there is no laboratory study of the infiltration performance of ICBPs that combines clogging levels with variables related with the topography of car parks such as runoff surface length (R(SL)) and surface slope (S(S)). This paper studies the infiltration behaviour of ICBP during their operational life in a car park using an improved version of the Cantabrian Fixed (CF) Infiltrometer. This laboratory device simulates direct rainfall and runoff from adjacent impervious areas over an ICBPs surface of 0.25 m(2) for different slopes (0, 3, 5, 7 and 10%) and three scenarios of clogging (surface newly built, surface clogged and surface clogged with maintenance). This paper presents the results of the tests and a statistical analysis based on three regression models (corresponding to each clogging scenario) depending on the R(SL) and S(S) variables. All models passed a confidence level of 95%, presenting high R(2) values and showing that R(SL) is a more influential variable than the S(S) for all clogging scenarios.

Design and construction of an experimental pervious paved parking area to harvest reusable rainwater.

Pervious pavements are sustainable urban drainage systems already known as rainwater infiltration techniques which reduce runoff formation and diffuse pollution in cities. The present research is focused on the design and construction of an experimental parking area, composed of 45 pervious pavement parking bays. Every pervious pavement was experimentally designed to store rainwater and measure the levels of the stored water and its quality over time. Six different pervious surfaces are combined with four different geotextiles in order to test which materials respond better to the good quality of rainwater storage over time and under the specific weather conditions of the north of Spain. The aim of this research was to obtain a good performance of pervious pavements that offered simultaneously a positive urban service and helped to harvest rainwater with a good quality to be used for non potable demands.

Long-term analysis of clogging and oil bio-degradation in a System of Catchment, Pre-treatment and Treatment (SCPT).

Runoff contamination has motivated the development of different systems for its treatment in order to decrease the pollutant load that is discharged into natural water bodies. In the long term, these systems may undergo operational problems. This paper presents the results obtained in a laboratory study with a 1:1 scale prototype of a System of Catchment, Pre-treatment and Treatment (SCPT) of runoff waters. The analysis aims to establish the operational behaviour of the SCPT in the long term with respect to oil degradation and hydraulic conductivity in the geotextile filter. It is concluded that bio-degradation processes take place inside the SCPT and that hydraulic conductivity of the geotextile filtration system decreases slowly with successive simulated runoff events.

Sistemas urbanos de drenaje sostenible (SUDS) / Sustainable urban drainage systems (SUDS)

Este trabajo trata sobre los sistemas urbanos de drenaje sostenible (SUDS) o mejores prácticas de gestión (BMPs). El concepto de desarrollo sostenible aplicado al drenaje urbano supone la aplicación de estos sistemas con la intención de evitar problemas como inundaciones, contaminación difusa o pérdida de riqueza natural. Las principales técnicas son medidas preventivas, superficies permeables, pozos y zanjas de infiltración, depósitos de infiltración, drenes filtrantes o drenes franceses, cunetas verdes, franjas filtrantes, depósitos de detención, estanques de retención y humedales. Mediante un método multidisciplinar de selección de SUDS para resolver el drenaje urbano, se constituye una cadena de tratamiento cuyo resultado depende, no sólo de los eslabones, sino también del ajuste entre ellos. Todo ello con el fin de cumplir las condiciones en cuanto a cantidad, calidad y servicio impuestas por el criterio de diseño