A Comparison of Three-Layer and Single-Layer Small Vascular Grafts Manufactured via the Roto-Evaporation Method.

This study used the roto-evaporation technique to engineer a 6 mm three-layer polyurethane vascular graft (TVG) that mimics the architecture of human coronary artery native vessels. Two segmented polyurethanes were synthesized using lysine (SPUUK) and ascorbic acid (SPUAA), and the resulting materials were used to create the intima and adventitia layers, respectively. In contrast, the media layer of the TVG was composed of a commercially available polyurethane, Pearlbond 703 EXP. For comparison purposes, single-layer vascular grafts (SVGs) from individual polyurethanes and a polyurethane blend (MVG) were made and tested similarly and evaluated according to the ISO 7198 standard. The TVG exhibited the highest circumferential tensile strength and longitudinal forces compared to single-layer vascular grafts of lower thicknesses made from the same polyurethanes. The TVG also showed higher suture and burst strength values than native vessels. The TVG withstood up to 2087 ± 139 mmHg and exhibited a compliance of 0.15 ± 0.1%/100 mmHg, while SPUUK SVGs showed a compliance of 5.21 ± 1.29%/100 mmHg, akin to coronary arteries but superior to the saphenous vein. An indirect cytocompatibility test using the MDA-MB-231 cell line showed 90 to 100% viability for all polyurethanes, surpassing the minimum 70% threshold needed for biomaterials deemed cytocompatibility. Despite the non-cytotoxic nature of the polyurethane extracts when grown directly on the surface, they displayed poor fibroblast adhesion, except for SPUUK. All vascular grafts showed hemolysis values under the permissible limit of 5% and longer coagulation times.

A Novel In Situ Sol-Gel Synthesis Method for PDMS Composites Reinforced with Silica Nanoparticles.

The addition of nanostructures to polymeric materials allows for a direct interaction between polymeric chains and nanometric structures, resulting in a synergistic process through the physical (electrostatic forces) and chemical properties (bond formation) of constituents for the modification of their properties and potential cutting-edge materials. This study explores a novel in situ synthesis method for PDMS-%SiO2 nanoparticle composites with varying crosslinking degrees (PDMS:TEOS of 15:1, 10:1, and 5:1); particle concentrations (5%, 10%, and 15%); and sol-gel catalysts (acidic and alkaline). This investigation delves into the distinct physical and chemical properties of silicon nanoparticles synthesized under acidic (SiO2-a) and alkaline (SiO2-b) conditions. A characterization through Raman, FT-IR, and XPS analyses confirms particle size and agglomeration differences between both the SiO2-a and SiO2-b particles. Similar chemical environments, with TEOS and ethanol by-products, were detected for both systems. The results on polymer composites elucidate the successful incorporation of SiO2 nanoparticles into the PDMS matrix without altering the PDMS's chemical structure. However, the presence of nanoparticles did affect the relative intensities of specific vibrational modes over composites from -35% to 24% (Raman) and from -14% to 59% (FT-IR). The XPS results validate the presence of Si, O, and C in all composites, with significant variations in atomic proportions (C/Si and O/Si) and Si and C component analyses through deconvolution techniques. This study demonstrates the successful in situ synthesis of PDMS-SiO2 composites with tunable properties by controlling the sol-gel and crosslinking synthesis parameters. The findings provide valuable insights into the in situ synthesis methods of polymeric composite materials and their potential integration with polymer nanocomposite processing techniques.

Antimicrobial and antitumor activities of an alginate-based membrane loaded with bismuth nanoparticles and cetylpyridinium chloride.

OBJECTIVE: To evaluate the antitumor and antimicrobial properties of an alginate-based membrane (ABM) loaded with bismuth lipophilic nanoparticles (BisBAL NPs) and cetylpyridinium chloride (CPC) on clinically isolated bacteria and a pancreatic cancer cell line. MATERIAL AND METHODS: The BisBAL NP-CPC ABM was characterized using optical and scanning electron microscopy (SEM). The antimicrobial potential was measured using the disk-diffusion assay, and antibiofilm activity was determined through the live/dead assay and fluorescence microscopy. The antitumor activity was analyzed on the pancreatic cell line (Panc 03.27) using the MTT assay and live/dead assay with fluorescence microscopy. RESULTS: After a 24-h exposure (37°C, aerobic conditions), 5 µM BisBAL NP reduced the growth of K. pneumoniae by 77.9%, while 2.5 µM BisBAL NP inhibited the growth of Salmonella, E. faecalis and E. faecium by 82.9%, 82.6%, and 78%, respectively (p < 0.0001). The BisBAL NPs-CPC ABM (at a ratio of 10:1; 500 and 50 µM, respectively) inhibited the growth of all isolated bacteria, producing inhibition halos of 9.5, 11.2, 7, and 10.3 mm for K. pneumoniae, Salmonella, E. faecalis, and E. faecium, respectively, in contrast to the 6.5, 9.5, 8.5, and 9.8 mm obtained with 100 µM ceftriaxone (p < 0.0001). The BisBAL NPs-CPC ABM also reduced bacterial biofilms, with 81.4%, 74.5%, 97.1%, and 79.5% inhibition for K. pneumoniae, E. faecium, E. faecalis, and Salmonella, respectively. Furthermore, the BisBAL NPs-CPC ABM decreased Panc 03.27 cell growth by 76%, compared to 18% for drug-free ABM. GEM-ABM reduced tumoral growth by 73%. The live/dead assay confirmed that BisBAL NPs-CPC-ABM and GEM-ABM were cytotoxic for the turmoral Panc 03.27 cells. CONCLUSION: An alginate-based membrane loaded with BisBAL NP and CPC exhibits dual antimicrobial and antitumoral efficacy. Therefore, it could be applied in cancer treatment and to diminish the occurrence of surgical site infections.

Mechanical Properties of Poly(Alkenoate) Cement Modified with Propolis as an Antiseptic.

BACKGROUND: We assessed the effect of propolis on the antibacterial, mechanical, and adhesive properties of a commercial poly(alkenoate) cement. METHODS: The cement was modified with various concentrations of propolis, and antibacterial assays were performed against S. mutans by both MTT assays and agar diffusion tests. The compressive, flexural, and adhesive properties were also evaluated. RESULTS: the modified cement showed activity against S. mutans in both assays, although reductions in compressive (from 211.21 to 59.3 MPa) and flexural strength (from 11.1 to 6.2 MPa) were noted with the addition of propolis, while adhesive strength (shear bond strength and a novel pull-out method) showed a statistical difference (p < 0.05). CONCLUSION: the antiseptic potential of modified material against S. mutans will allow this material to be used in cases in which low mechanical resistance is required (in addition to its anti-inflammatory properties) when using atraumatic restorative techniques, especially in deep cavities.

Novel copper complexes-polyurethane composites that mimics anti-inflammatory response.

Copper is a trace element of biological significance that can form complexes with several thiol containing compounds which can be used as filler in biomedical polyurethanes. In this work, segmented polyurethanes (SPUs) were synthesized with thiol containing compounds as chain extenders including d-penicillamine (DP), l-penicillamine (LP), l-cysteine (LC) and reduced glutathione (GR). Then, the synthesized polyurethane was filled with copper chelates based on the same chain extenders. Evidence of free thiol containing chain extender in polyurethane was not observed by FTIR and Raman but EDX provided evidence of sulfur in the unfilled polyurethane and copper and sulfur in their composite. DSC and DRX showed the semi-crystalline nature of the polyurethanes which provided good mechanical properties, especially to those prepared with DP. The Tg of the PCL determined by DMA shifted toward higher temperatures by the addition of copper complexes while TGA studies showed that the thermal degradation was slightly improved when LCCu and GRCu complex were added. Macrophage viability was observed in all composition studied after longer times of extraction (72 h) and dilutions (1:2 to 1:32) but remarkably high in those prepared with LCCu and GRCu. The anti-inflammatory response was proved in LC and GR copper complex filled polyurethanes as IL-4 and IL-10 increased with time while IL-1ß and TNF-α were reduced.

Effects of Neutralization on the Physicochemical, Mechanical, and Biological Properties of Ammonium-Hydroxide-Crosslinked Chitosan Scaffolds.

It has been reported that chitosan scaffolds, due to their physicochemical properties, stimulate cell proliferation in different tissues of the human body. This study aimed to determine the physicochemical, mechanical, and biological properties of chitosan scaffolds crosslinked with ammonium hydroxide, with different pH values, to better understand cell behavior depending on the pH of the biomaterial. Scaffolds were either neutralized with sodium hydroxide solution, washed with distilled water until reaching a neutral pH, or kept at alkaline pH. Physicochemical characterization included scanning electron microscopy (SEM), elemental composition (EDX), Fourier-transform infrared (FTIR) spectroscopy, Raman spectroscopy, thermogravimetric analysis (TGA), and mechanical testing. In vitro cytotoxicity was assessed via dental-pulp stem cells' (DPSCs') biocompatibility. The results revealed that the neutralized scaffolds exhibited better cell proliferation and morphology. It was concluded that the chitosan scaffolds' high pH (due to residual ammonium hydroxide) decreases DPSCs' cell viability.

Antioxidant Capacity, Vitamin C and Polyphenol Profile Evaluation of a Capsicum chinense By-Product Extract Obtained by Ultrasound Using Eutectic Solvent.

Habanero pepper leaves and stems (by-products) have been traditionally considered waste; however, bioactive compounds such as polyphenols, vitamin C and carotenoids have been identified that can be used for formulation of nutraceuticals or functional foods. Furthermore, the extraction of these bioactive compounds by using environmentally friendly methods and solvents is desirable. Thus, the aim of this study was to assess the antioxidant capacity, total polyphenol content (TPC), the phenolic profile and vitamin C content in extracts obtained from by-products (stems and leaves) of two varieties (Mayapan and Jaguar) of habanero pepper by ultrasound-assisted extraction (UAE) using natural deep eutectic solvents (NADES). The results showed that NADES leads to extracts with significantly higher TPC, higher concentrations of individual polyphenols (gallic acid, protocatechuic acid, chlorogenic acid, cinnamic acid, coumaric acid), vitamin C and, finally, higher antioxidant capacity (9.55 ± 0.02 eq mg Trolox/g DM) than UAE extraction performed with methanol as the solvent. The association of individual polyphenols with NADES was confirmed by principal component analysis (PCA). Overall, NADES is an innovative and promising "green" extraction technique that can be applied successfully for the extraction of phenolic compounds from habanero pepper by-products.

Zinc Oxide and Copper Chitosan Composite Films with Antimicrobial Activity.

The role of the oral microbiome and its effect on dental diseases is gaining interest. Therefore, it has been sought to decrease the bacterial load to fight oral cavity diseases. In this study, composite materials based on chitosan, chitosan crosslinked with glutaraldehyde, chitosan with zinc oxide particles, and chitosan with copper nanoparticles were prepared in the form of thin films, to evaluate a new alternative with a more significant impact on the oral cavity bacteria. The chemical structures and physical properties of the films were characterized using by Fourier transform infrared spectroscopy (FTIR,) Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), elemental analysis (EDX), thermogravimetric analysis (TGA), X-ray diffraction (XRD), scanning electron microscopy (SEM), and contact angle measurements. Subsequently, the antimicrobial activity of each material was evaluated by agar diffusion tests. No differences were found in the hydrophilicity of the films with the incorporation of ZnO or copper particles. Antimicrobial activity was found against S. aureus in the chitosan film crosslinked with glutaraldehyde, but not in the other compositions. In contrast antimicrobial activity against S. typhimurium was found in all films. Based on the data of present investigation, chitosan composite films could be an option for the control of microorganisms with potential applications in various fields, such as medical and food industry.

Antibacterial activity of a glass ionomer cement doped with copper nanoparticles.

Copper nanoparticles (NCu) were synthetized and added to commercial glass ionomer cement, to evaluate in vitro its antibacterial activity against oral cavity strains. The NCu were synthesized by copper acetate reduction with L-ascorbic acid and characterized by FTIR, Raman, XPS, XRD and TEM. Then, commercial glass ionomer cement (GIC) was modified (MGIC) with various concentrations of NCu and physicochemically characterized. Cell viability was tested against human dental pulp fibroblasts (HDPFs) by Alamar-Blue assay and antibacterial test was performed against S. mutans and S. sanguinis by colony forming unit (CFU) growth method. Synthesized NCu rendered a mixture of both metallic copper and cuprous oxide (Cu2O). HDPF viability reduces with exposure time to the extracts (68-72% viability) and MGIC with 2-4 wt% NCu showed antimicrobial activity against the two tested strains.

The Effect of PEGDE Concentration and Temperature on Physicochemical and Biological Properties of Chitosan.

Chitosan (CHT) is a polysaccharide with multiple claimed properties and outstanding biocompatibility, generally attributed to the presence of protonable amino groups rendering a cationic natural polymer. However, the effect of changes in CHT structure due to hydration is not considered in its performance. This study compares the effects on biocompatibility after drying at 25 °C and 150 °C scaffolds of chitosan, polyethylene glycol diglycidyl ether (PEGDE) crosslinked CHT (low, medium and high concentration) and glutaraldehyde (GA) crosslinked CHT. PEGDE crosslinked CHT showed a reduction in free amino groups and the amide I/II ratio, which exhaustive drying reduced further. In X-ray diffraction (DRX) analysis, PEGDE crosslinked CHT showed multiple peaks, whereas the crystallinity percentage was reduced with an increase in PEGDE concentration and thermal treatments at 150 °C. In a direct contact cell assay, high osteoblast viability was achieved at low and medium PEDGE concentrations, which was improved when the crosslinked scaffolds were thermally treated at 150 °C. This was attributed to its partial hydrophilicity, low crystallinity and low surface roughness; this in spite of the small reduction in the amount of free amino groups on the surface induced during drying at 150 °C. Furthermore, PEGDE crosslinked CHT scaffolds showed strong vinculin and integrin 1ß expression, which render them suitable for bone contact applications.

Titanium - castor oil based polyurethane composite foams for bone tissue engineering.

Polyurethanes (PU) foams with titanium particles (Ti) were prepared with castor oil (CO) and isophorone diisocyanate (IPDI) as polymeric matrix, and 1, 3 and 5 wt.% of Ti. Composites were physicochemically and mechanically characterized and their biocompatibility assessed using human dental pulp stem cells (HDPSC). PU synthesis was confirmed by FTIR, but the presence of Ti was detected by RAMAN, X-ray diffraction (peak at 2θ = 40.2°) and by EDX-mapping. Materials showed three decomposition temperatures between 300 °C and 500 °C and their decomposition were not catalyzed by Ti particles. Compressive modulus (164-846 kPa), compressive strength (12.9-116.7 kPa) and density (128-240 kg/m3) tend to increase with Ti concentration but porosity was reduced (87% to 80%). Composites' foams were fully degraded in acid and oxidative media while remained stable in distilled water. HDPSC viability on all composites was higher than 80% up to 14 days while proliferation dropped up to 60% at 21 days. Overall, these results suggest that these foams can be used as scaffolds for bone tissue regeneration.

Preparation and characterization of titanium-segmented polyurethane composites for bone tissue engineering.

Segmented polyurethanes were prepared with polycaprolactone diol as soft segment and 4,4-methylene-bis cyclohexyl diisocyanate and l-glutamine as the rigid segment. These polyurethanes were filled with 1 wt.% to 5 wt.% titanium particles (Ti), physicochemically characterized and their biocompatibility assessed using human dental pulp stem cells and mice osteoblasts. Physicochemical characterization showed that composites retained the properties of the semicrystalline polyurethane as they exhibited a glass transition temperature (Tg) between -35°C and -45°C, melting temperature (Tm) at 52°C and crystallinity close to 40% as determined by differential scanning calorimetry. In agreement with this, X-ray diffraction showed reflections at 21.3° and 23.6° for polycaprolactone diol and reflections at 35.1°, 38.4°, and 40.2° for Ti particles suggesting that these particles are not acting as nucleating sites. The addition of up to 5 wt.% of Ti reduced both, tensile strength and maximum strain from 1.9 MPa to 1.2 MPa, and from 670% to 172% for pristine and filled polyurethane, respectively. Although there were differences between composites at low strain rates, no significant differences in mechanical behavior were observed at higher strain rate where a tensile stress of 8.5 MPa and strain of 223% were observed for 5 wt.% composites. The addition to titanium particles had a beneficial effect on both human dental pulp stem cells and osteoblasts viability, as it increased with the amount of titanium in composites up to 10 days of incubation.

Comparative study on the properties of acrylic bone cements prepared with either aliphatic or aromatic functionalized methacrylates.

Bone cements prepared with methacrylic acid (MAA) and diethyl amino ethyl methacrylate (DEAEM) were compared with formulations employing 4-methacryloyloxybenzoic acid (MBA) and 4-diethyaminobenzyl methacrylate (DEABM) as comonomer. The influence of these new aromatic monomers on various physicochemical, setting and mechanical properties was assessed. Surface characterization demonstrated that bone cements prepared with any of the functionalized monomers exhibited increasing hydrophilicity with monomer concentration and that the aromatic monomers provided more hydrophilic cements than their aliphatic counterparts for low concentrations of the functional monomer. It was also found that bone cements prepared with high amounts of the acidic aliphatic monomer provided the highest exotherm of reaction and their setting times were shorter than MBA based cements. On the other hand, DEABM containing bone cements exhibited shorter setting times than DEAEM formulations and slightly higher peak temperatures. In general, it was found that the glass transition temperature increased with the presence of acidic comonomer and decreased when alkaline comonomers were present, especially aliphatic ones. When aromatic methacrylates were used at 0.05 molar fraction, the highest tensile and compressive strength were achieved i.e. 46 and 118 MPa for MBA and 51 and 108 MPa for DEABM formulations. A further increase in the aromatic monomer concentration led to cements of low mechanical properties due to solubility problems as revealed by SEM.