ABSTRACT
In the past few decades, there has been continued interest in shape memory polymers (SMPs), and tremendous efforts have been made to develop multifunctional composites of these SMPs to enhance the existing properties of SMPs. Although fossil-based sources are widely used in the production of shape memory polymer composites (SMPCs), the depletion of fossil-based resources and associated environmental problems increase interest toward renewable biobased products synthesized from natural resources. This study aims to produce alkaline lignin-reinforced SMPCs by using alkaline lignin in the SMP matrix. Thermo-mechanical, morphological, and shape memory tests are performed in order to reveal the effect of alkaline lignin usage in the SMP matrix on SMPC production. Differential scanning calorimetry analysis results show that adding alkaline lignin into the SMP matrix with 1 and 3% ratios led to an increase in T g values, while raising the alkaline lignin ratio to 5% decreased the T g value. According to the DMA results, increasing the alkaline lignin ratios caused an increase in the storage modulus of SMPCs, and the best storage modulus value was obtained at the 5% alkaline lignin ratio. The results of the three-point bending test also confirmed the results obtained from the DMA analysis, showing that an increasing alkaline lignin ratio caused an increase in the bending modulus. Scanning electron microscopy analysis showed a rough structure in 1 and 3% alkaline lignin supplementation, while a smoother structure was observed in 5% alkaline lignin supplementation. The smoother structure of the sample containing 5% alkaline lignin indicates that alkaline lignin supplementation exhibits a smoother surface by showing a plasticizing effect. As a result, it was observed that increasing the lignin ratio increased the polymer/alkaline lignin interaction, resulting in a harder structure and an increase in the flexural modulus value.
ABSTRACT
Carbon derived from various biomass sources has been evaluated as support material for thermal energy storage systems. However, process optimization of Miscanthus-derived carbon to be used for encapsulating phase change materials has not been reported to date. In this study, process optimization to evaluate the effects of selected operation parameters of pyrolysis time, temperature, and biomass:catalyst mass ratio on the surface area and pore volume of produced carbon is conducted using response surface methodology. In the process, ZnCl2 is used as a catalyst to promote high pore volume and area formation. Two sets of optimum conditions with different pyrolysis operation parameters in order to produce carbons with the highest pore area and volume are determined as 614 °C, 53 min, and 1:2 biomass to catalyst ratio and 722 °C, 77 min, and 1:4 biomass to catalyst ratio with 1415.4 m2/g and 0.748 cm3/g and 1499.8 m2/g and 1.443 cm3/g total pore volume, respectively. Carbon material produced at 614 °C exhibits mostly micro- and mesosized pores, while carbon obtained at 722 °C comprises mostly of meso- and macroporous structures. Findings of this study demonstrate the significance of process optimization for designing porous carbon material to be used in thermal and electrochemical energy storage systems.
ABSTRACT
The production of lactic acid, a polylactic acid monomer from energy crop Miscanthus × giganteus lignocellulosic biomass cultivated in Izmir was investigated. Liquid hot water (LHW) pretreatment was carried out at a temperature range of 140-200 °C, pressure 100 to 200 bar and reaction time of 15-45 min at a fixed flow rate of 2 mL/min using D-optimal experimental plan. The optimum conditions were elicited as 140 °C, 100 bar and 45 minutes, yielding the highest reducing sugar content of 77.32 mg/g, whereas 1.25 mg/mL arabinose and 1.35 mg/mL xylose as monomeric sugars. Subsequently, the enzymatic hydrolysis was applied to the solid fraction. The optimum conditions for enzymatic hydrolysis were determined as 5% (w/v) solid/liquid ratio, 20 FPU/mL enzyme loading and 72 hours, revealing the highest amount of reducing sugar as 200 mg/mL. LHW hydrolysate was used as a production medium for lactic acid manufacturing in submerged fermentation by Rhizopus oryzae. The maximum lactic acid content was found to be 6.8 g/L at 24 hours, whereas the lactic acid yield was 0.28 g/L.h. The sequential design of LHW, followed by enzymatic hydrolysis and submerged lactic acid fermentation can be utilized in industry, contributing to the bioeconomy.
Subject(s)
Carbohydrates , Lactic Acid , Water , Fermentation , Xylose , HydrolysisABSTRACT
Sustainable energy production is a worldwide concern due to the adverse effects and limited availability of fossil fuels, requiring the development of suitable environmentally friendly alternatives. Hydrogen is considered a sustainable future energy source owing to its unique properties as a clean and nontoxic fuel with high energy yield and abundance. Hydrogen can be produced through renewable and nonrenewable sources where the production method and feedstock used are indicators of whether they are carbon-neutral or not. Biomass is one of the renewable hydrogen sources that is also available in large quantities and can be used in different conversion methods to produce fuel, heat, chemicals, etc. Biomass gasification is a promising technology to generate carbon-neutral hydrogen. However, tar production during this process is the biggest obstacle limiting hydrogen production and commercialization of biomass gasification technology. This review focuses on hydrogen production through catalytic biomass gasification. The effect of different catalysts to enhance hydrogen production is reviewed, and social, technological, economic, environmental, and political (STEEP) analysis of catalysts is carried out to demonstrate challenges in the field and the development of catalysts.
ABSTRACT
The extracts of Stevia rebaudiana are marketed as dietary supplements and utilized as natural sweetening agent in food products. Subsequent to extraction on industrial scale, large quantities of solid wastes are produced. The aim of this study was to investigate the bioconversion efficiency of supercritical CO(2) extracted S. rebaudiana residues. Therefore, leaves were extracted with supercritical CO(2) and ethanol mixture in order to obtain glycosides, then the raffinate phase was hydrolyzed by both dilute acid and various concentrations of cellulase and ß-glucosidase cocktail. The maximum yield of reducing sugars reached 25.67 g/L under the optimal conditions of enzyme pretreatment, whereas 32.00 g/L was reached by consecutive enzymatic and acid hydrolyses. Bioethanol yield (20 g/L, 2.0% inoculum, 2 days) based on the sugar consumed was 45.55% corresponding to a productivity of 0.19 kg/m(3)h which demonstrates challenges to be utilized as a potential feedstock for the production of bioethanol.
