Variable aperture controlled by microelectrofluidic iris.

This Letter presents an adaptive liquid iris based on microelectrofluidic technology with experimental results. In the microelectrofluidic iris (MEFI), the electrostatic force generated by electrowetting in a surface channel unbalances the Laplace pressure acting on two fluidic interfaces between air and a light-absorbing liquid in two connected surface channels in a chamber. Then, the changed net pressure makes the iris aperture of the liquid diaphragm adjustable. The present MEFI was designed to have a tunable range from 4.2 to 0.85 mm in diameter and a tuning ratio of 80%. The MEFI was fabricated with a transparent electrode patterned on three glass plates and two channel spacers. Concerning the optical and interfacial properties of the MEFI for its operation, an aqueous near-infrared dye used in optical coherence tomography (OCT) was forced into a ring shape as the driving liquid in the hydrophobic chamber. By switching the segmented concentric control electrodes in steps, digital operation of the MEFI was successfully observed with clear aperture stops. The measured turnaround speed was 80 mm/s, which is significantly higher than that for other comparable adaptive liquid irises. Due to a scalable aperture range with fast response, the concept of MEFI is expected to be widely applied in various optical systems that require high-quality imaging, as well as in real-time diagnostic OCT.

Adaptive optical probe design for optical coherence tomography and microscopy using tunable optics.

We present a tunable, adaptive optical imaging probe for multimodal imaging such as optical coherence tomography and microscopy. The probe is compatible with forward-looking scanning laser imaging devices such as an endoscope. The lens configuration includes a tunable iris and two varifocal lenses, both driven by microelectrofluidics, as well as several conventional fixed focus lenses. The modulation transfer function and spot size in the focal plane is evaluated, and we show using optical simulations that there are three possible imaging modes with different transverse resolutions and focal depths.

Zoom lens design using liquid lens for laparoscope.

Traditional laparoscopic optical systems consisting of about 30 lenses have low optical magnification. To magnify tissue during surgical operations, one must change from one laparoscope to another or use a magnifying adapter between the laparoscope and the sensor. Our work focuses on how to change the sag of a liquid lens while zooming from 1 × zoom, to 2 × , and 4 × in an optical design for a laparoscope. The design includes several lenses and two liquid lenses with variable focal lengths. A pair of laparoscopes for 3-D stereoscopy is placed within a tube 11 mm in diameter. The predicted depth resolution of tissue is 0.5 mm without interpolation at 4 × zoom.

Varifocal liquid lens based on microelectrofluidic technology.

This Letter presents a tunable liquid lens based on microelectrofluidic technology. In the microelectrofluidic lens (MEFL), electrowetting in the hydrophobic surface channel induces the Laplace pressure difference between two fluidic interfaces on the lens aperture and the surface channel. Then, the pressure difference makes the lens curvature tunable. In spite of the contact angle saturation, the narrow surface channel increases the Laplace pressure to have a wide range of optical power variation in the MEFL. The magnitude of the applied voltage determines the lens curvature in the analog mode MEFL. Digital operation is also possible when the control electrodes of the MEFL are patterned to have an array. The lens aperture and maximum surface channel diameter were designed to 3.2 mm and 6.4 mm, respectively, with a channel height of 0.2 mm for an optical power range between +210 and -30 D. By switching the control electrodes, the averaged transit time in steps and turnaround time were as low as 2.4 ms and 16.5 ms, respectively, in good agreement with the simulation results. It is expected that the proposed MEFL may be widely used with advantages of wide variation of the optical power with fast and precise controllability in a digital manner.

Wettability control of a transparent substrate using ZnO nanorods.

This paper presents a simple way of controlling the wettability of a structured surface with ZnO nanorods on a transparent substrate. A combination of ZnO nanostructures and stearic acid was used to create superhydrophobic surfaces with the potential properties of being self-cleaning, waterproof, and antifog. ZnO nanorods were uniformly covered on glass substrates through a simple hydrothermal method with varying growth time which affects the surface morphology. When a substrate is dipped into 10 mM stearic acid in ethanol for 24 h, chemisorption of the stearic acid takes place on the ZnO nanorod surface, after which the hydrophilic ZnO nanorod surfaces are modified into hydrophobic ones. The contact angle of a water droplet on this superhydrophobic ZnO nanorod surface increased from 110 degrees to 150 degrees depending on the growth time (from 3 to 6 h) with a high transparency of above 60%. In addition, the water contact angle can be made to as low as 27 degrees after exposing the substrate to 10-mW/cm2 UV for 1 h.

An electrochemical route to graphene oxide.

Large-scale graphene oxide (GO) with adjustable resistivity was synthesized from graphite via an electrochemical method using KCl solution as an effective electrolyte. During the exfoliation process, electrostatic force intercalates chloride ions between the expanded graphite layers on the anode. These chloride ions form small gas bubbles between the graphite layers in the electrochemical reaction. It is believed that the gas bubbles expand the gap between graphite sheets and produce a separating force between adjacent graphene layers. This separating force overcomes the Van der Waals force between adjacent sheets and exfoliates graphene layers from the starting graphite. Because the graphene is electrochemically oxidized by chorine during the exfoliation, the exfoliated GO sheets are hydrophilic and easily dispersed in the electrolyte solution. The GO solution prepared by the electrochemical exfoliation can be simply sprayed or spin-coated onto any substrate for device applications. The measured average thicknesses of a monolayer, bilayer, and trilayer exfoliated GO on SiO2 substrate were 1.9, 2.8, and 3.9 nm, respectively. It was observed that the measured resistance of the exfoliated GO sheets increases due to electrochemical oxidation in the solution. This electrochemical approach offers a low-cost and efficient route to the fabrication of graphene based devices.

Electrical characteristics of various submucosal injection fluids for endoscopic mucosal resection.

Submucosal fluid injection, prerequisite to endoscopic mucosal resection, necessitates detailed evaluation for proper selection. We aimed to compare height of gastric tissues after submucosal injection, and to verify electrical implications of injectants. Porcine stomach pieces were cut out, and eight solutions were used: normal saline, 0.5% sodium hyaluronate (SH), 0.25% SH, hydroxypropyl methylcellulose, 10% glycerin, fibrinogen, 1% sodium alginate (SA), and 2.5% SA. Elevated heights were measured after submucosal injection of the eight fluids, and electrical impedance was measured for fluids plus a reference solution (0.01 N KCl) with a potentiostat electroimpedance spectrometry and an insulation-tipped knife. Resistivity was calculated thereafter. Normal saline and 10% glycerin solution showed greater height diminution. Resistivity were in the range of 80-110 Omega cm, except for 309.7 Omega cm for fibrinogen. Higher resistivity may improve performance of electrosurgery, probably by strengthening impedance and heat dissipation. Further studies are required to back up this basic experiment for clinical application.