Effect of biomass retention time on performance and fouling of a stirred membrane photobioreactor.

Co-culture of microalgae-activated sludge has the potential to purify wastewater while reduce energy demand from aeration. In this work, a mechanically stirred membrane photobioreactor (stirred-MPBR) was used to evaluate the impact of the biomass retention time (BRT) on the treatment performance and membrane fouling. Results showed that stirred-MPBR was affected by BRT during treating domestic wastewater at a flux of 16.5 L m-2 h-1. The highest productivity was attained at BRT 7d (102 mg L-1 d-1), followed by BRT 10d (86 mg L-1 d-1), BRT 5d (85 mg L-1 d-1), and BRT 3d (83 mg L-1 d-1). Statistical analysis results showed that BRT 7d had a higher COD removal rate than BRT 10d, however, there is no difference in total nitrogen removal rate. The highest TP removal occurred when the biomass operated at BRT as short as 3d. Reduced BRTs caused a change in the microalgae-activated sludge biomass fraction that encouraged nitrification activity while simultaneously contributing to a higher fouling rate. The bound protein concentrations dropped from 31.35 mg L-1 (BRT 10d) to 10.67 mg L-1 (BRT 3d), while soluble polysaccharides increased from 0.99 to 1.82 mg L-1, respectively. The concentrations of extracellular polymeric substance fractions were significantly altered, which decreased the mean floc size and contributed to the escalating fouling propensity. At the optimum BRT of 7d, the stirred-MPBR showed sufficient access to light and nutrients exchange for mutualistic interactions between the microalgae and activated sludge.

Enhanced understanding of osmotic membrane bioreactors through machine learning modeling of water flux and salinity.

Mathematical modeling can be helpful to understand and optimize osmotic membrane bioreactors (OMBR), a promising technology for sustainable wastewater treatment with simultaneous water recovery. Herein, seven machine learning (ML) algorithms were employed to model both water flux and salinity of a lab-scale OMBR. Through the optimum hyperparameters tuning and 5-fold cross-validation, the ML models have achieved more accurate results without obvious overfitting and bias. The median R2 scores of water flux modeling were all over the 0.95 and the most of median R2 scores from total dissolved solids (TDS) modeling were higher than 0.90. During model testing, random forest (RF) algorithm presented the highest R2 score of 0.987 with the lowest root mean square error (RMSE = 0.044) for the water flux modeling, and extreme gradient boosting (XGB) algorithm exhibited the best results (R2 = 0.97; RMSE = 0.234) in the TDS modeling. The Shapley Additive exPlanations (SHAP) analysis found that the phosphorus concentration was a critical input feature for both water flux and TDS modeling. Finally, the selected ML models were used to predict water flux and salinity affected by two input features and the predication results confirmed the importance of the phosphate concentration. The results of this study have demonstrated the promise of ML modeling for investigating OMBR systems.

Water reclamation and microbial community investigation: Treatment of tetramethylammonium hydroxide wastewater through an anaerobic osmotic membrane bioreactor hybrid system.

Tetramethylammonium hydroxide (TMAH) is a toxic photoresist developer used in the photolithography process in thin-film transistor liquid crystal display (TFT-LCD) production, and it can be removed through anaerobic treatment. TMAH cannot be released into the environment because of its higher toxicity. A tight membrane, such as a forward osmosis (FO) membrane, together with an anaerobic biological process can ensure that no TMAH is released into the environment. Thus, for the first time, an anaerobic osmotic membrane bioreactor (AnOMBR) hybrid system was developed in this study to treat a low-strength TMAH wastewater and to simultaneously investigate its microbial community. Microfiltration extraction was used to mitigate the salinity accumulation, and a periodically physical water cleaning was utilized to mitigate the FO membrane fouling. The diluted draw solute (MgSO4) was reconcentrated and reused by a membrane distillation (MD) process in the AnOMBR to achieve 99.99% TMAH removal in this AnOMBR-MD hybrid system, thereby ensuring that no TMAH is released into the natural environment. Moreover, the membrane fouling in the feed and draw sides were analyzed through the fluorescence excitation-emission matrix (FEEM) spectrophotometry to confirm that the humic acid-like materials were the primary membrane fouling components in this AnOMBR. Additionally, 16S rRNA metagenomics analysis indicated that Methanosaeta was the predominant contributor to methanogenesis and proliferated during the long-term operation. The methane yield was increased from 0.2 to 0.26 L CH4/g COD when the methanogen species acclimatized to the saline system.

Microplastics waste in environment: A perspective on recycling issues from PPE kits and face masks during the COVID-19 pandemic.

During the COVID-19 pandemic, the extensive use of face masks and protective personal equipment (PPE) kits has led to increasing degree of microplastic pollution (MP) because they are typically discarded into the seas, rivers, streets, and other parts of the environment. Currently, microplastic (MP) pollution has a negative impact on the environment because of high-level fragmentation. Typically, MP pollution can be detected by various techniques, such as microscopic analysis, density separation, and Fourier transform infrared spectrometry. However, there are limited studies on disposable face masks and PPE kits. A wide range of marine species ingest MPs in the form of fibers and fragments, which directly affect the environment and human health; thus, more research and development are needed on the effect of MP pollution on human health. This article provides a perspective on the origin and distribution of MP pollution in waterbodies (e.g., rivers, ponds, lakes, and seas) and wastewater treatment plants, and reviews the possible remediation of MP pollution related to the excessive disposal of face masks and PPE kits to aquatic environments.

Preparation of Metal Modified onto Biochar from Hazardous Waste for Arsenic Removal.

Use of urban sludge, hospital sludge, and aquatic product sludge as a biochar adsorbent from wastewater treatment plants was investigated. Microwave carbonization was used to carbonize the sludge and then chemically activated at high temperatures to increase porosity and surface area. Effective of arsenic adsorption in water presents a newly designed metal doped to biochar. The biochar was characterized by scanning electron microscope (SEM) with energy dispersive X-ray (EDS), nitrogen adsorption/desorption isotherm analyzer (BET), thermo gravimetric analysis (TGA) and X-ray diffraction (XRD) analysis. Results display uniform pore sizes and high surface area (>490 m²g-1) of the biochar. Thence, urban sludge, hospital sludge, and aquatic product sludge can be used as carbon sources. The highest amount of Fe, Mn, and Ni loading onto the biochar was determined to be 8.0%, 6.0% and 10.0%, respectively. All biochar samples have arsenic adsorption capacities positively correlated with initial concentration. The corresponding removal efficiency of As(V) is 98% and As(III) is 84% at pH 3 with an adsorption capacity of 4.12 and 3.6 mg g-1, respectively. The adsorption capacity of As(V) and As(III) clearly decreased in the presence of PO43- (2.34 and 1.46 mg g-1, respectively). Due to competition for adsorption sites, the PO43- can effectively reduce arsenic adsorption. The arsenic species adsorption-desorption recycles on biochar are also discussed.

A breakthrough dynamic-osmotic membrane bioreactor/nanofiltration hybrid system for real municipal wastewater treatment and reuse.

This study designed a Dynamic-Osmotic membrane bioreactor/nanofiltration (OsMBR/NF) system for municipal wastewater treatment and reuse. Results indicated that a continuously rotating FO module with 60 RPM in Dynamic-OsMBR system could enhance shear stress and reduce cake layer of foulants, leading to higher flux (50%) compared to Traditional-OsMBR during a 40-operation day. A negligible specific reverse salt flux (0.059 G/L) and a water flux of 2.86 LMH were recorded when a mixture of 0.1 M EDTA-2Na/0.1 M Na2CO3/0.9 mM Triton114 functioned as draw solution (DS). It was found that the Dynamic-OsMBR/NF hybrid system could effectively remove pollutants (∼98% COD, ∼99% PO43-P, ∼93% NH4+-N, > 99% suspended solids) from wastewater. In short, this developed system can be considered a breakthrough technology as it successfully minimizes membrane fouling by shear force, and achieves high water quality for reuse by two membrane- barriers.

Microbial community response to ciprofloxacin toxicity in sponge membrane bioreactor.

This study aims to offer insights into how ciprofloxacin (CIP) impact bacterial community structures in the Sponge-MBR process when CIP is spiked into hospital wastewater. We found that the CIP toxicity decreased richness critical phylotypes such as phylum class ẟ-, ß-, É£-proteobacteria, and Flavobacteria that co-respond to suppress denitrification and cake fouling to 37% and 28% respectively. Cluster analysis shows that the different community structures were formed under the influence of CIP toxicity. CIP decreased attached growth biomass by 2.3 times while increasing the concentration of permeate nitrate by 3.8 times, greatly affecting TN removal by up to 26%. Ammonia removal was kept stable by inflating the ammonia removal rate (p < 0.003), with the wealthy Nitrospira genus guaranteeing the nitrification activity. In addition, we observed an increasing richness of Chloroflexi and Planctomycetes, which may play a role in fouling reduction in the Sponge-MBR. Therefore, if the amount of antibiotics in hospital wastewater continues to increase, it is so important to extend biomass retention for denitrification recovery.

Adsorption Configurations of Iron Complexes on As(III) Adsorption Over Sludge Biochar Surface.

Waste recycling and reuse will result in significant material and energy savings. In this research, usage of hospital sludge as a biochar adsorbent for wastewater treatment plants was investigated. Microwave carbonization was used to carbonize the sludge and then chemically activated with ZnCl2to increase surface area and porosity. A newly designed iron metal doped sludge biochar carbon (SBC) has effective adsorption of inorganic arsenic (As(III), As2O3) in water. The findings clearly demonstrate the viability and utility of using hospital sludge as a source of carbon to generate SBC. The adsorption mechanism of As(III) on SBC's iron-metal-modified surface has been studied using density functional theory (DFT) to understand the impact of functional complexes on adsorption As(III). Tests showed physical as well as chemical adsorption of As(III) on Fe-SBC surface. Fe's involvement in functional complexes greatly fostered SBC surface activity and it's As(III) adsorption ability. The physical adsorption energies of As(III) with Fe functional complexes on the SBC surface were -42.3 KJ mol-1. Other hand, the chemical adsorption energies of As(III) on Fe-SBC surface was -325.5 KJ mol-1. As(III) is capable of interacting in a bidentate fashion with the dopants through the protonated oxygen atoms and this conformation of the cyclic structure is higher in the adsorption energy than the others.

Aqueous Oxytetracycline and Norfloxacin Sonocatalytic Degradation in the Presence of Peroxydisulfate with Multilayer Sheet-Like Zinc Oxide.

Multilayer ZnO sheet-like flakes were synthesized by a simple method of precipitation and characterized by the techniques of X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). The findings are proven that the SEM images show the overall morphology of a single sheet-like ZnO nanostructure made from uniformly thick nano-sheets. In an aqueous environment, the acoustic ability of the prepared material was assessed using ultrasound (US) radiation to degrade oxytetracycline (OTC) and norfloxacin (NF). To increase the degradation efficiency, a US/ZnO/peroxodisulfate system was developed by introducing ammonium persulfate ((NH4)2S2O8) and sodium persulfate (Na2S2O8), exhibiting excellent synergistic effects. Result show the decomposition efficiency for NF removal with Na2S2O8 (64%) appeared to be slightly better than with (NH4)2S2O8 (56%). By contrast, the ultrasonic catalytic efficiency of Na2S2O8 (98%) was slightly better than that of (NH4)2S2O8 (94%) for OTC removal. The addition of scavengers to the US/ZnO/peroxodisulfate system through the NF and OTC results in the largest effect of holes. The degradation is considered to be often caused by holes. In this system, the Na2S2O8 can have two roles to increase the rate of degradation: (1) The SO4- formed by Na2S2O8 under ultrasonic irradiation directly degraded to norfloxacin on ZnO surface; and (2) S2O82- behaved as an electron acceptor, inhibiting recombination of electron hole pairs, enabling the development of more ·OH. Therefore, the synergistic effect significantly increases US/ZnO/peroxodisulfate sonocatalytic activity (Hu, S.B., et al., 2017. Aqueous norfloxacin sonocatalytic degradation with multilayer flower-like ZnO in the presence of peroxydisulfate. Ultrasonics Sonochemistry, 38(1), pp.446-454).

Efficient Cu removal from CuEDTA complex-containing wastewater using electrochemically controlled sacrificial iron anode.

In this study, an electro-replacement/precipitation/deposition/direct reduction (ERPDD) process with scrap iron packed in a Ti mesh cage as a sacrificial anode was investigated for the treatment of wastewater containing CuEDTA complexes. The ERPDD mechanisms were responsible for the removal of Cu from CuEDTA complexes and were verified by a series of experiments using either iron or carbon plates as anodes for the Cu-containing solutions with and without EDTA. A complete Cu removal was achieved with electrical current density applied (1.18-2.36 mA/cm2), whereas only 60% of the Cu was removed without electricity. Dissolved oxygen (DO) was found to have a significant impact on Cu removal. Aeration reduced Cu removal (i.e., only 60% of the Cu was removed), whereas complete Cu removal was achieved with negligible DO concentration under mechanical mixing and N2 purging conditions. Compared to chemical replacement/precipitation (CRP) process, the ERPDD was able to save approximately 60-75% of the total operational costs during the treatment of CuEDTA-containing wastewater, due to the electrochemically controlled dosing of inexpensive sacrificial scrap iron and additional removal mechanisms not found in the CRP process.

Recovery of iodide as triiodide from thin-film transistor liquid crystal display wastewater by forward osmosis.

Triiodide, a larger charged molecule compared to iodide, is thermodynamically favored with the presence of both iodide and iodine, and is easier to be retained by membrane processes. For the first time, iodide was recovered in the form of triiodide by forward osmosis (FO) for thin-film transistor liquid crystal display industries by preoxidation of iodide to triiodide. Partial oxidation by NaOCl was used to convert the iodide to iodine and then to form triiodide. Ethylenediaminetetraacetic acid disodium salt (EDTA-2Na), a commonly used chelating agent in the industry, was used as the draw solute because of its low reverse salt flux. The results revealed that the ideal efficiency of iodide recovery was at pH 3 with a preoxidation (adding 0.0150 M NaClO) for the 0.048 M iodide wastewater with a recovery of 98.5%. Additionally, the Pourbaix diagram and starch indicator were used to verify the formation of triiodide. Membrane distillation was demonstrated to recover the EDTA-2Na draw solute, and more than 99% of recoveries for the draw solutes with initial water flux of 12.0 L/m2 h were achieved, indicating that simultaneous recovery of the EDTA-2Na draw solute and water is feasible.

A novel thermophilic anaerobic granular sludge membrane distillation bioreactor for wastewater reclamation.

Membrane distillation (MD) has a high heat requirement. Integrating MD with thermophilic bioreactors could remedy this problem. A laboratory-scale thermophilic anaerobic granular sludge membrane distillation bioreactor (ThAGS-MDBR) was used to treat wastewater with a high organic loading rate (OLR). Waste heat from ThAGS was used directly for the MD process to reduce energy consumption. The result demonstrated that the ThAGS-MDBR system achieved a high-efficiency removal of chemical oxygen demand (more 99.5%) and NH4+-N (96.4%). Furthermore, the highest methane production from the proposed system was 332 mL/g CODremoved at OLR of 16 kg COD/m3/day. Specifically, an aggregate of densely packed diverse microbial communities in anaerobic granular sludge was the main mechanism for the enhancement of bioreactor tolerance with environmental changes. High-quality distillate water from ThAGS-MDBR was reclaimed in one step with total organic carbon less than 1.7 mg/L and electrical conductivity less than 120 µS/cm. Furthermore, the result of the DNA extraction kit recorded that Methanosaeta thermophila was a critical archaea for high COD removal and bioreactor stability.

Recent Developments in Nanomaterials-Modified Membranes for Improved Membrane Distillation Performance.

Membrane distillation (MD) is a thermally induced membrane separation process that utilizes vapor pressure variance to permeate the more volatile constituent, typically water as vapor, across a hydrophobic membrane and rejects the less volatile components of the feed. Permeate flux decline, membrane fouling, and wetting are some serious challenges faced in MD operations. Thus, in recent years, various studies have been carried out on the modification of these MD membranes by incorporating nanomaterials to overcome these challenges and significantly improve the performance of these membranes. This review provides a comprehensive evaluation of the incorporation of new generation nanomaterials such as quantum dots, metalloids and metal oxide-based nanoparticles, metal organic frameworks (MOFs), and carbon-based nanomaterials in the MD membrane. The desired characteristics of the membrane for MD operations, such as a higher liquid entry pressure (LEPw), permeability, porosity, hydrophobicity, chemical stability, thermal conductivity, and mechanical strength, have been thoroughly discussed. Additionally, methodologies adopted for the incorporation of nanomaterials in these membranes, including surface grafting, plasma polymerization, interfacial polymerization, dip coating, and the efficacy of these modified membranes in various MD operations along with their applications are addressed. Further, the current challenges in modifying MD membranes using nanomaterials along with prominent future aspects have been systematically elaborated.

Water and nutrient recovery by a novel moving sponge - Anaerobic osmotic membrane bioreactor - Membrane distillation (AnOMBR-MD) closed-loop system.

For the first time, a novel sponge-based moving bed-anaerobic osmosis membrane bioreactor/membrane distillation (AnOMBR/MD) system using mixed Na3PO4/EDTA-2Na as the draw solution was employed to treat wastewater for enhanced water flux and reduced membrane fouling. Results indicated that the moving sponge-AnOMBR/MD system obtained a stable water flux of 4.01 L/m2 h and less membrane fouling for a period lasting 45 days. Continuous moving sponge around the FO module is the main mechanism for minimizing membrane fouling during the 45-day AnOMBR operation. The proposed system's nutrient removal was almost 100%, thus showing the superiority of simultaneous FO and MD membranes. Nutrient recovery from the MF permeate was best when solution pH was controlled to 9.5, whereby 17.4% (wt/wt) of phosphorus was contained in precipitated components. Moreover, diluted draw solute following AnOMBR was effectively regenerated using the MD process with water flux above 2.48 L/m2 h and salt rejection > 99.99%.

Application of progressive freezing on forward osmosis draw solute recovery.

Progressive freezing is a solvent purification technology with low energy requirements and high concentration efficiency. Although these advantages make it a promising technology, the technique has never been explored for draw solution recovery for forward osmosis (FO). Hence, in this study, the progressive freezing process was used to concentrate three common diluted draw solutions: NaCl, MgCl2, and EDTA-2Na with different ice front speeds, stirring rates, and initial draw solution concentrations. Effective partition and intrinsic partition constants were also evaluated. The results reveal that the freezing process can achieve a draw solution recovery rate of 99.73%, 99.06%, and 98.65% with NaCl, MgCl2, and EDTA-2Na, respectively, using an ice front speed of 0.5 cm/h, a stirring rate of 2.62 m/s, and 30% of percentage of ice phase. Higher concentration efficiency for NaCl and MgCl2 was achieved due to the high solubility of NaCl and MgCl2 increased solute diffusion into the liquid phase solutions. The concentration factors for all three draw solutions exceeded 1.9, indicating that the draw solutes could be reused for the FO process. In addition, the two mass transfer coefficients depended on the ice front speed and the stirring rates were also obtained for scaling up the experiment in the future.

Exploring Nanosilver-Coated Hollow Fiber Microfiltration to Mitigate Biofouling for High Loading Membrane Bioreactor.

For the first time, a nanosilver-coated hollow fiber microfiltration (MF) was fabricated by a simple chemical reduction method, then tested for membrane biofouling mitigation study under extreme high mixed liquor suspended solid (MLSS) concentration for long term. This study presents a simple and novel technique to modify a commercially available MF membrane using silver nanoparticles (AgNPs) followed by an investigation of mitigating membrane biofouling potentials using this modified membrane to compare with an unmodified membrane for 60-day operation period. The modified membranes showed that AgNPs was attached to the MF-membrane successfully with a high density of 119.85 ± 5.42 mg/m2. After long-term testing of 60 days in membrane bioreactor with a MLSS concentration of 11,000 mg/L, specific flux of the AgNPs coated MF (AgNPs-MF) decreased 59.7%, while the specific flux of the unmodified membrane dropped 81.8%, resulted from the increase of transmembrane vacuum pressure for the AgNPs-MF was lower than that of the unmodified one. The resistance-in-series model was used to calculate the resistance coefficients of membrane modules, and the result showed that the cake layer resistance coefficient of the unmodified membrane was 2.7 times higher than that of the AgNPs-MF after the 60-day operation, confirming that AgNPs displayed great antimicrobial properties to mitigate membrane biofouling under such high MLSS.

Innovative upflow anaerobic sludge osmotic membrane bioreactor for wastewater treatment.

A novel upflow anaerobic sludge-forward osmotic membrane bioreactor was developed for simultaneous wastewater treatment, membrane fouling reduction, and nutrient recovery. An upflow anaerobic sludge blanket (UASB) reactor was incorporated into the system, suspending the anaerobic sludge at the bottom of the reactor. A forward osmosis membrane replaced the traditional three-phase separator of the UASB technology. The removals of chemical oxygen demand, PO43-, and NH4+ were all more than 95% with low membrane fouling in this system. Halotolerant Fusibacter, which can ferment organics to acetate, was increased rapidly from 0.1% to 5% in this saline environment. Acetoclastic Methanosaeta was the most dominant prokaryotes and responsible for majority of methane production. Reduction of membrane fouling in this system was verified by the fluorescence excitation-emission matrix spectrophotometry. Furthermore, phosphorus recovery and salinity build-up mitigation were achieved using periodic microfiltration to recover 57-105 mg/L phosphorus from pH 9 to 12.

Hospital wastewater treatment by sponge membrane bioreactor coupled with ozonation process.

Herein, a sponge membrane bioreactor (Sponge-MBR) combined with ozonation process was performed to remove the antibiotics which frequently existed in the hospital wastewater. Whilst seven antibiotics i.e., norfloxacin, ciprofloxacin, ofloxacin, sulfamethoxazole, erythromycin, tetracycline and trimethoprim were widely used in medications, this integration was applied for the evaluation of treatment performance under different fluxes. As the results, whilst the antibiotics were eliminated about 45-93%, the tetracycline was completely removed (100%) using Sponge-MBR operated at the flux of 10 LMH. For enhancement of antibiotics removal, the ozonation process was introduced to treat the membrane permeate. Overall efficiencies were 97 ±â€¯2% (trimethoprim), 92 ±â€¯4% (norfloxacin), 90 ±â€¯1% (erythromycin), 88 ±â€¯4% (ofloxacin), 83 ±â€¯7 (ciprofloxacin) and 66 ±â€¯1% (sulfamethoxazole). These results demonstrated Sponge-MBR coupled with ozonation could be a prospective technology for the hospital wastewater treatment.

A comprehensive review of recent developments in 3D printing technique for ceramic membrane fabrication for water purification.

Additive manufacturing (AM), which is also commonly known as 3D printing, provides flexibility in the manufacturing of complex geometric parts at competitive prices and within a low production time. However, AM has not been used to a large extent in filtration and water treatment processes. AM results in the creation of millions of nanofibers that are sublayered on top of each other and compressed into a thin membrane. AM is a novel technique for fabricating filtration membranes with different shapes, sizes and controlled porosity, which cannot be achieved using conventional process such as electrospinning and knife casting. In this paper, we review the advantages and limitations of AM processes for fabricating ceramic membranes. Moreover, a brief background of AM processes is provided, and their future prospects are examined. Due to their potential benefits for fabrication and flexibility with different materials, AM methods are promising in the field of membrane engineering.

Effect of ciprofloxacin dosages on the performance of sponge membrane bioreactor treating hospital wastewater.

This study aimed to evaluate treatment performance and membrane fouling of a lab-scale Sponge-MBR under the added ciprofloxacin (CIP) dosages (20; 50; 100 and 200 µg L-1) treating hospital wastewater. The results showed that Sponge-MBR exhibited effective removal of COD (94-98%) during the operation period despite increment of CIP concentrations from 20 to 200 µg L-1. The applied CIP dosage of 200 µg L-1 caused an inhibition of microorganisms in sponges, i.e. significant reduction of the attached biomass and a decrease in the size of suspended flocs. Moreover, this led to deteriorating the denitrification rate to 3-12% compared to 35% at the other lower CIP dosages. Importantly, Sponge-MBR reinforced the stability of CIP removal at various added CIP dosages (permeate of below 13 µg L-1). Additionally, the fouling rate at CIP dosage of 200 µg L-1 was 30.6 times lower compared to the control condition (no added CIP dosage).