Polyethylene-Based Knee Spacer for Infection Control: Design Concept and Pre-Clinical In Vitro Validations.

Antibiotic-loaded polymethyl methacrylate (PMMA) has been widely applied in the treatment of knee periprosthetic joint infections. However, problems with antibiotic-loaded PMMA-based spacers, such as structural fracture and implant dislocation, remain unresolved. A novel polyethylene-based spacer, designed with an ultra-congruent articulating surface and multiple fenestrations, was introduced in the current study. Validation tests for biomechanical safety, wear performance, and efficacy of antibiotic cement were reported. During cycle fatigue testing, no tibial spacer failures were observed, and less wear debris generation was reported compared to commercial PMMA-based spacers. The volumetric wear of the novel spacer was within the safety threshold for osteolysis-free volumetric wear. An effective infection control was demonstrated despite the application of lesser antibiotic cement in the 30-day antibiotic elution test. The tube dilution test confirmed adequate inhibitory capabilities against pathogens with the loaded antibiotic option utilized in the current study. The novel polyethylene-based knee spacer may offer sufficient biomechanical safety and serve as an adequate carrier of antibiotic-loaded cement for infection control. Further clinical trials shall be conducted for more comprehensive validation of the novel spacer for practical application.

[Research progress on the osseointegration of titanium implants promoted by cold atmospheric plasma].

The application of cold atmospheric plasma to titanium surface modification has recently become a research focus in the area of material modification. Previous studies found that cold atmospheric plasma can affect the colonization of bacteria and biological behaviors of osteoblasts by changing the surface characteristics of titanium in vitro. In vivo studies reveal that cold atmospheric plasma can promote the process of osseointegration of titanium implants. This review focuses on research on the effects of the surface modification of titanium implants with cold atmospheric plasma on osseointegration.

[All-ceramic premolar guiding plate retains resin-bonded fixed partial dentures].

OBJECTIVE: This study aims to investigate the fracture resistance and short-term restorative effects of resin-bonded fixed partial dentures (RBFPDs) made from heat-pressed lithium-disilicate-based glass-ceramic (IPS e.max press) and zirconia ceramic (WIELAND) and retained by all-ceramic guiding plates when used to restore missing mandibular second premolars. METHODS: A total of 64 human mandibular first premolars and first molars were prepared as abutments, then were randomly divided into 4 groups (n=8): E0, heat-pressed ceramic RBFPDs, no cyclic loading; E1, heat-pressed ceramic RBFPDs exposed to 300 000 cycles of dynamic loading; W0, zirconia ceramic RBFPDs, no cyclic loading; and W1, zirconia ceramic RBFPDs exposed to 300 000 cycles of dynamic loading. Fracture strength was tested in a universal testing machine. RESULTS: The medians of fracture strength were 1 242.85 N±260.11 N (E0), 1 650.85 N±206.77 N (W0), 1 062.60 N±179.98 N (E1), and 1 167.61 N±265.50 N (W1). Statistical analysis showed that all the groups exhibited significantly higher fracture strength compared with the maximum bite force in the premolar region (360 N; P<0.001). The W0 group had significantly higher fracture strength than the E0 group (P<0.05). Meanwhile, no significant difference in fracture strength was observed between the E1 and W1 groups (P>0.05). Significant statistical differences were found between the zirconia ceramic groups (W0 and W1, P<0.05) but not between the glassceramic groups (E0 and E1, P>0.05) after dynamic loading. CONCLUSIONS: The RBFPDs retained by all-ceramic guiding plates exhibited promising fracture properties and optimal short-term restorative effects when used to restore missing mandibular second premolars.

Importance of a moderate plate-to-bone distance for the functioning of the far cortical locking system.

The far cortical locking (FCL) system, a novel bridge-plating technique, aims to deliver controlled and symmetric interfragmentary motion for a potential uniform callus distribution. However, clinical data for the practical use of this system are limited. The current study investigated the biomechanical effect of a locking plate/far cortical locking construct on a simulated comminuted diaphyseal fracture of the synthetic bones at different distance between the plate and the bone. Biomechanical in vitro experiments were performed using composite sawbones as bone models. A 10-mm osteotomy gap was created and bridged with FCL constructs to determine the construct stiffness, strength, and interfragmentary movement under axial compression, which comprised one of three methods: locking plates applied flush to bone, at 2 mm, or at 4 mm from the bone. The plate applied flush to the bone exhibited higher stiffness than those at 2 mm and 4 mm plate elevation. A homogeneous interfragmentary motion at the near and far cortices was observed for the plate at 2 mm, whereas a relatively large movement was observed at the far cortex for the plate applied at 4 mm. A plate-to-bone distance of 2 mm had the advantages of reducing axial stiffness and providing nearly parallel interfragmentary motion. The plate flush to the bone prohibits the dynamic function of the far cortical locking mechanism, and the 4-mm offset was too unstable for fracture healing.

Partially threaded headless screw may benefit adequate interfragmentary compression and reduced driving torque for small bone fixation.

Headless compression screws (HCSs) are commonly used to fixate small bones and articular fractures. Understanding the biomechanical efficacy of different HCS designs can help surgeons make proper interfragmentary compression when a specific implant is chosen. HCSs with three different central shaft designs (unthreaded, fully threaded, and partially threaded) were studied: the Herbert-Whipple, Mini-Acutrak 2, and headless reduction (HLR). Polyurethane foam blocks were machined with a simulated fracture gap of 0.5 mm and set onto a custom-made jig to simultaneously measure compression force and driving torque during screw insertion. The maximal achievable compression forces and driving torques recorded were 47.4 ± 0.9 N and 145.11 ± 1.65 N mm for the HLR, 50.98 ± 1.29 N and 152.62 ± 2.83 N mm for the Mini-Acutrak 2, and 19.33 ± 1.0 N and 33.4 ± 2.2 N mm for the Herbert-Whipple. Overall, the compression force of the Mini-Acutrak 2 and HLR increased with the torque. Unlike the other screws, the Herbert-Whipple's driving torque increased while the compression force decreased after peak compression force was achieved. The partially threaded shaft design (HLR) demonstrated equivalent biomechanical advantage with the Mini-Acutrak 2 in interfragmentary compression. The HCSs with cone-shaped proximal ends (HLR and Mini-Acutrak 2) maintained their compression force during over-fastening, whereas the unthreaded central shaft of the Herbert-Whipple screw caused it to lose compression force.

Anatomic Locking Plate for Displaced Intraarticular Calcaneal Fracture: Design and Application.

Calcaneal fracture can lead to long-term disability and have a considerable economic effect. Most calcaneal fractures are intraarticular fractures involving the posterior facet of the subtalar joint. Treating displaced intraarticular calcaneal fractures is complicated because of the lack of an optimal treatment option. Internal fixation typically involves screw-and-plate implants, which can be unfavorable owing to the lack of an anatomic design and the intraoperative bending required for the plate to contour to the irregular surface of the calcaneus. We assessed the outcomes of 30 patients treated using innovative, anatomically designed calcaneal locking plates and the perceived advantages for surgeons. Postoperative computed tomography images of the affected feet were obtained, and the functional performance was recorded. The mean average Böhler angle had increased significantly from 16.8° ± 14.9° to 28.5° ± 9.4° (p < .001). The mean average maximal fracture gap and maximal step-off in the posterior facet of the subtalar joint in the coronal computed tomography images also decreased significantly from 2.8 ± 3.7 mm to 0.8 ± 1.3 mm (p < .01) and from 3.3 ± 2.8 mm to 0.8 ± 1.2 mm (p < .001), respectively. The mean average American Orthopaedic Foot and Ankle Ankle-Hindfoot scale score was 93.9 ± 7.1 at the final follow-up visit. In addition, the surgical time was reduced because bending the plate was not required and the quality of reduction could be assessed easily by examining the gap between the cortex and the plate. The results were promising, revealing that the anatomic locking plate can be used effectively in the treatment of displaced intraarticular calcaneal fractures using simple reduction techniques with a potentially shortened operating time.

Larger screw diameter may not guarantee greater pullout strength for headless screws - a biomechanical study.

Headless compression screws (HCSs) are commonly utilized devices for small bone fracture fixation. The Mini-Acutrak 2 and headless reduction (HLR) screws are the newer version types, in which both have fully threaded and variable pitch design. Specifically, the HLR is characterized by two thread runouts to facilitate implantation. With the thread runouts, the holding strength of the screw may be compromised. To the best of our knowledge, no study has examined the pullout force of the global sizes of a HCS. We sought to determine the pullout strength of the HLR and compare the strength of this screw with that of the Mini-Acutrak 2. Synthetic bone blocks with simulated transverse fractures were used to conduct the tests. Four commonly used sizes of the HLR were examined, and one Mini-Acutrak 2 was employed for comparison. Five screws of each size were tested. The pullout force of all screws that were tested in this study ranged from 45.23 to 233.22 N. The results revealed that the pullout force increased as the screw diameter increased. Interestingly, we found that one small screw outperformed the Mini-Acutrak 2, which has a larger diameter. This study provided extensive knowledge regarding the pullout strength of fully threaded HCSs of different sizes. An unexpected finding is that a small screw has higher holding power than a large one because of its increased number of threads. Therefore, we suggest that the thread number should be a critical consideration for the design of size distribution of HCSs.

Conceptual finite element study for comparison among superior, anterior, and spiral clavicle plate fixations for midshaft clavicle fracture.

Open reduction internal fixation technique has been generally accepted for treatment of midshaft clavicle fractures. Both superior and anterior clavicle plates have been reported in clinical or biomechanical researches, while presently the spiral clavicle plate design has been introduced improved biomechanical behavior over conventional designs. In order to objectively realize the multi-directional biomechanical performances among the three geometries for clavicle plate designs, a current conceptual finite element study has been conducted with identical cross-sectional features for clavicle plates. The conceptual superior, anterior, and spiral clavicle plate models were constructed for virtual reduction and fixation to an OTA 15-B1.3 midshaft transverse fracture of clavicle. Mechanical load cases including cantilever bending, axial compression, inferior bending, and axial torsion have been applied for confirming the multi-directional structural stability and implant safety in biomechanical perspective. Results revealed that the anterior clavicle plate model represented lowest plate stress under all loading cases. The superior clavicle plate model showed greater axial compressive stiffness, while the anterior clavicle plate model performed greater rigidity under cantilever bending load. Three model represented similar structural stiffness under axial torsion. Played as a transition structure between superior and anterior clavicle plate, the spiral clavicle plate model revealed comparable results with acceptable multi-directional biomechanical behavior. The concept of spiral clavicle plate design is worth considering in practical application in clinics. Implant safety should be further investigated by evidences in future mechanical tests and clinical observations.

Biomechanical effect of the configuration of screw hole style on locking plate fixation in proximal humerus fracture with a simulated gap: A finite element analysis.

BACKGROUND: Locking plate fixation for proximal humeral fractures is a commonly used device. Recently, plate breakages were continuously reported that the implants all have a mixture of holes allowing placement of both locking and non-locking screws (so-called combi plates). In commercialized proximal humeral plates, there still are two screw hole styles included "locking and dynamic holes separated" and "locking hole only" configurations. It is important to understand the biomechanical effect of different screw hole style on the stress distribution in bone plate. METHODS: Finite element method was employed to conduct a computational investigation. Three proximal humeral plate models with different screw hole configurations were reconstructed depended upon an identical commercialized implant. A three-dimensional model of a humerus was created using process of thresholding based on the grayscale values of the CT scanning of an intact humerus. A "virtual" subcapital osteotomy was performed. Simulations were performed under an increasing axial load. The von Mises stresses around the screw holes of the plate shaft, the construct stiffness and the directional displacement within the fracture gap were calculated for comparison. RESULTS: The mean value of the peak von Mises stresses around the screw holes in the plate shaft was the highest for combi hole design while it was smallest for the locking and dynamic holes separated design. The stiffness of the plate-bone construct was 15% higher in the locking screw only design (132.6N/mm) compared with the combi design (115.0N/mm), and it was 4% higher than the combi design for the locking and dynamic holes separated design (119.5N/mm). The displacement within the fracture gap was greatest in the combi hole design, whereas it was smallest for the locking hole only design. CONCLUSIONS: The computed results provide a possible explanation for the breakages of combi plates revealed in clinical reports. The locking and dynamic holes separated design may be a better configuration to reduce the risk of plate fracture.

Biomechanical comparison of conventional and anatomical calcaneal plates for the treatment of intraarticular calcaneal fractures - a finite element study.

Initial stability is essential for open reduction internal fixation of intraarticular calcaneal fractures. Geometrical feature of a calcaneal plate is influential to its endurance under physiological load. It is unclear if conventional and pre-contoured anatomical calcaneal plates may exhibit differently in biomechanical perspective. A Sanders' Type II-B intraarticular calcaneal fracture model was reconstructed to evaluate the effectiveness of calcaneal plates using finite element methods. Incremental vertical joint loads up to 450 N were exerted on the subtalar joint to evaluate the stability and safety of the calcaneal plates and bony structure. Results revealed that the anatomical calcaneal plate model had greater average structural stiffness (585.7 N/mm) and lower von Mises stress on the plate (774.5 MPa) compared to those observed in the conventional calcaneal plate model (stiffness: 430.9 N/mm; stress on plate: 867.1 MPa). Although both maximal compressive and maximal tensile stress and strain were lower in the anatomical calcaneal plate group, greater loads on fixation screws were found (average 172.7 MPa compared to 82.18 MPa in the conventional calcaneal plate). It was noted that high magnitude stress concentrations would occur where the bone plate bridges the fracture line on the lateral side of the calcaneus bone. Sufficient fixation strength at the posterolateral calcaneus bone is important for maintaining subtalar joint load after reduction and fixation of a Sanders' Type II-B calcaneal fracture. In addition, geometrical design of a calcaneal plate should worth considering for the mechanical safety in practical usage.

Biomechanical effect of different femoral neck blade position on the fixation of intertrochanteric fracture: a finite element analysis.

Medial migration or cutout of the neck helical blade has commonly occurred in the treatment of trochanteric fracture of the femur. The position of the helical blade within the femoral head is one of the influencing factors that cause the blade to perforate the intact joint surface; however, the ideal placement of the helical blade is not currently known. A finite element model of a femur/nail construct was utilized to analyze five possible blade positions in the femoral head. Normal strain at the fracture surface, the minimum principal strain in the cancellous bone, and the von Mises stress in the implant itself were calculated and compared between different blade positions. The results showed that a large area of normal compressive strain at the fracture surface was observed in the inferior and posterior blade positions. The volume of cancellous bone strained to yielding in the femoral head and neck was lower for the inferior and posterior positions, whereas it was the highest for the superior position. The inferior and posterior positions had lower von Mises stress in the implant itself. The inferior and posterior positions may be the ideal position for the intramedullary nail with a helical neck blade.

Change in collateral ligament length and tibiofemoral movement following joint line variation in TKA.

PURPOSE: The primary intent of total knee arthroplasty is the restoration of normal knee kinematics, with ligamentous constraint being a key influential factor. Displacement of the joint line may lead to alterations in ligament attachment sites relative to knee flexion axis and variance of ligamentous constraints on tibiofemoral movement. This study aimed to investigate collaterals strains and tibiofemoral kinematics with different joint line levels. METHODS: A previously validated knee model was employed to analyse the change in length of the collateral ligaments and tibiofemoral motion during knee flexion. The models shifted the joint line by 3 and 5 mm both proximally and distally from the anatomical level. The data were captured from full extension to flexion 135°. RESULTS: The elevated joint line revealed a relative increase in distance between ligament attachments for both collateral ligaments in comparison with the anatomical model. Also, tibiofemoral movement decreased with an elevation in the joint line. Conversely, lowering the joint line led to a significant decrease in distance between ligament attachments, but greater tibiofemoral motion. CONCLUSION: Elevation of the joint line would strengthen the capacity of collateral ligaments for knee motion constraint, whereas a distally shifted joint line might have the advantage of improving tibiofemoral movement by slackening the collaterals. It implies that surgeons can appropriately change the joint line position in accordance with patient's requirement or collateral tensions. A lowered joint line level may improve knee kinematics, whereas joint line elevation could be useful to maintain knee stability. LEVEL OF EVIDENCE: V.

Effect of different radial hole designs on pullout and structural strength of cannulated pedicle screws.

Cannulated pedicle screws are designed for bone cement injection to enhance fixation strength in severely osteoporotic spines. However, the screws commonly fracture during insertion. This study aims to evaluate how different positions/designs of radial holes may affect the pullout and structural strength of cannulated pedicle screws using finite element analysis. Three different screw hole designs were evaluated under torsion and bending conditions. The pullout strength for each screw was determined by axial pullout failure testing. The results showed that when the Von Mises stress reached the yield stress of titanium alloy the screw with four radial holes required a greater torque or bending moment than the nine and twelve hole screws. In the pullout test, the strength and stiffness of each screw with cement augmentation showed no significant differences, but the screw with four radial holes had a greater average pullout strength, which probably resulted from the significantly greater mean maximum lengths of cement augmentation. Superior biomechanical responses, with lower stress around the radial holes and greater pullout strength, represented by cannulated pedicle screw with four radial holes may worth recommending for clinical application.

The effect of graft strength on knee laxity and graft in-situ forces after posterior cruciate ligament reconstruction.

Surgical reconstruction is generally recommended for posterior cruciate ligament (PCL) injuries; however, the use of grafts is still a controversial problem. In this study, a three-dimensional finite element model of the human tibiofemoral joint with articular cartilage layers, menisci, and four main ligaments was constructed to investigate the effects of graft strengths on knee kinematics and in-situ forces of PCL grafts. Nine different graft strengths with stiffness ranging from 0% (PCL rupture) to 200%, in increments of 25%, of an intact PCL's strength were used to simulate the PCL reconstruction. A 100 N posterior tibial drawer load was applied to the knee joint at full extension. Results revealed that the maximum posterior translation of the PCL rupture model (0% stiffness) was 6.77 mm in the medial compartment, which resulted in tibial internal rotation of about 3.01°. After PCL reconstruction with any graft strength, the laxity of the medial tibial compartment was noticeably improved. Tibial translation and rotation were similar to the intact knee after PCL reconstruction with graft strengths ranging from 75% to 125% of an intact PCL. When the graft's strength surpassed 150%, the medial tibia moved forward and external tibial rotation greatly increased. The in-situ forces generated in the PCL grafts ranged from 13.15 N to 75.82 N, depending on the stiffness. In conclusion, the strength of PCL grafts have has a noticeable effect on anterior-posterior translation of the medial tibial compartment and its in-situ force. Similar kinematic response may happen in the models when the PCL graft's strength lies between 75% and 125% of an intact PCL.

Is the posterior cruciate ligament necessary for medial pivot knee prostheses with regard to postoperative kinematics?

PURPOSE: Excellent clinical and kinematical performance is commonly reported after medial pivot knee arthroplasty. However, there is conflicting evidence as to whether the posterior cruciate ligament should be retained. This study simulated how the posterior cruciate ligament, post-cam mechanism and medial tibial insert morphology may affect postoperative kinematics. METHODS: After the computational intact knee model was validated according to the motion of a normal knee, four TKA models were built based on a medial pivot prosthesis; PS type, modified PS type, CR type with PCL retained and CR type with PCL sacrificed. Anteroposterior translation and axial rotation of femoral condyles on the tibia during 0°-135° knee flexion were analyzed. RESULTS: There was no significant difference in kinematics between the intact knee model and reported data for a normal knee. In all TKA models, normal motion was almost fully restored, except for the CR type with PCL sacrificed. Sacrificing the PCL produced paradoxical anterior femoral translation and tibial external rotation during full flexion. CONCLUSION: Either the posterior cruciate ligament or post-cam mechanism is necessary for medial pivot prostheses to regain normal kinematics after total knee arthroplasty. The morphology of medial tibial insert was also shown to produce a small but noticeable effect on knee kinematics. LEVEL OF EVIDENCE: V.

Zebrafish WNK lysine deficient protein kinase 1 (wnk1) affects angiogenesis associated with VEGF signaling.

The WNK1 (WNK lysine deficient protein kinase 1) protein is a serine/threonine protein kinase with emerging roles in cancer. WNK1 causes hypertension and hyperkalemia when overexpressed and cardiovascular defects when ablated in mice. In this study, the role of Wnk1 in angiogenesis was explored using the zebrafish model. There are two zebrafish wnk1 isoforms, wnk1a and wnk1b, and both contain all the functional domains found in the human WNK1 protein. Both isoforms are expressed in the embryo at the initiation of angiogenesis and in the posterior cardinal vein (PCV), similar to fms-related tyrosine kinase 4 (flt4). Using morpholino antisense oligonucleotides against wnk1a and wnk1b, we observed that wnk1 morphants have defects in angiogenesis in the head and trunk, similar to flk1/vegfr2 morphants. Furthermore, both wnk1a and wnk1b mRNA can partially rescue the defects in vascular formation caused by flk1/vegfr2 knockdown. Mutation of the kinase domain or the Akt/PI3K phosphorylation site within wnk1 destroys this rescue capability. The rescue experiments provide evidence that wnk1 is a downstream target for Vegfr2 (vascular endothelial growth factor receptor-2) and Akt/PI3K signaling and thereby affects angiogenesis in zebrafish embryos. Furthermore, we found that knockdown of vascular endothelial growth factor receptor-2 (flk1/vegfr2) or vascular endothelial growth factor receptor-3 (flt4/vegfr3) results in a decrease in wnk1a expression, as assessed by in situ hybridization and q-RT-PCR analysis. Thus, the Vegf/Vegfr signaling pathway controls angiogenesis in zebrafish via Akt kinase-mediated phosphorylation and activation of Wnk1 as well as transcriptional regulation of wnk1 expression.

Biomechanical considerations in the design of high-flexion total knee replacements.

Typically, joint arthroplasty is performed to relieve pain and improve functionality in a diseased or damaged joint. Total knee arthroplasty (TKA) involves replacing the entire knee joint, both femoral and tibial surfaces, with anatomically shaped artificial components in the hope of regaining normal joint function and permitting a full range of knee flexion. In spite of the design of the prosthesis itself, the degree of flexion attainable following TKA depends on a variety of factors, such as the joint's preoperative condition/flexion, muscle strength, and surgical technique. High-flexion knee prostheses have been developed to accommodate movements that require greater flexion than typically achievable with conventional TKA; such high flexion is especially prevalent in Asian cultures. Recently, computational techniques have been widely used for evaluating the functionality of knee prostheses and for improving biomechanical performance. To offer a better understanding of the development and evaluation techniques currently available, this paper aims to review some of the latest trends in the simulation of high-flexion knee prostheses.

Biomechanical study of expandable pedicle screw fixation in severe osteoporotic bone comparing with conventional and cement-augmented pedicle screws.

Pedicle screws are widely utilized to treat the unstable thoracolumbar spine. The superior biomechanical strength of pedicle screws could increase fusion rates and provide accurate corrections of complex deformities. However, osteoporosis and revision cases of pedicle screw substantially reduce screw holding strength and cause loosening. Pedicle screw fixation becomes a challenge for spine surgeons in those scenarios. The purpose of this study was to determine if an expandable pedicle screw design could be used to improve biomechanical fixation in osteoporotic bone. Axial mechanical pull-out test was performed on the expandable, conventional and augmented pedicle screws placed in a commercial synthetic bone block which mimicked a human bone with severe osteoporosis. Results revealed that the pull-out strength and failure energy of expandable pedicle screws were similar with conventional pedicle screws augmented with bone cement by 2 ml. The pull-out strength was 5-fold greater than conventional pedicle screws and the failure energy was about 2-fold greater. Besides, the pull-out strength of expandable screw was reinforced by the expandable mechanism without cement augmentation, indicated that the risks of cement leakage from vertebral body would potentially be avoided. Comparing with the biomechanical performances of conventional screw with or without cement augmentation, the expandable screws are recommended to be applied for the osteoporotic vertebrae.

The effect of different humeral prosthesis fin designs on shoulder stability: a computational model.

Humeral prostheses commonly use a fin structure as an attachment point for the supraspinatus muscle in total shoulder arthroplasty (TSA), but these fins may cause injury to the muscle during implantation, inadvertently influencing stability. In order to prevent supraspinatus injury, the effect of different humeral prostheses on shoulder joint stability needs to be investigated. A commercially available prosthesis and two modified humeral prostheses that substituted the fin structure for 2 (2H) or 3 holes (3H) were evaluated using computational models. Glenohumeral abduction was simulated and the superioinferior/anterioposterior stability of the shoulder joint after TSA was calculated. The results revealed that the 2H design had better superioinferior stability than the other prostheses, but was still less stable than the intact shoulder. There were no obvious differences in anterioposterior stability, but the motion patterns were clearly distinguishable from the intact shoulder model. In conclusion, the 2H design showed better superioinferior stability than the 3H design and the commercial product during glenohumeral joint abduction; the three prostheses show similar results in anterioposterior stability. However, the stability of each tested prosthesis was not comparable to the intact shoulder. Therefore, as a compromise, the 2H design should be considered for TSA because of its superior stability.

Biomechanical analysis of different types of pedicle screw augmentation: a cadaveric and synthetic bone sample study of instrumented vertebral specimens.

This study aims to determine the pull-out strength, stiffness and failure pull-out energy of cement-augmented, cannulated-fenestrated pedicle screws in an osteoporotic cadaveric thoracolumbar model, and to determine, using synthetic bone samples, the extraction torques of screws pre-filled with cement and those with cement injected through perforations. Radiographs and bone mineral density measurements from 32 fresh thoracolumbar vertebrae were used to define specimen quality. Axial pull-out strength of screws was determined through mechanical testing. Mechanical pull-out strength, stiffness and energy-to-failure ratio were recorded for cement-augmented and non-cement-augmented screws. Synthetic bone simulating a human spinal bone with severe osteoporosis was used to measure the maximum extraction torque. The pull-out strength and stiffness-to-failure ratio of cement pre-filled and cement-injected screws were significantly higher than the non-cement-augmented control group. However, the cement pre-filled and cement-injected groups did not differ significantly across these values (p=0.07). The cement pre-filled group had the highest failure pull-out energy, approximately 2.8 times greater than that of the cement-injected (p<0.001), and approximately 11.5 times greater than that of the control groups (p<0.001). In the axial pull-out test, the cement-injected group had a greater maximum extraction torque than the cement pre-filled group, but was statistically insignificant (p=0.17). The initial fixation strength of cannulated screws pre-filled with cement is similar to that of cannulated screws injected with cement through perforations. This comparable strength, along with the heightened pull-out energy and reduced extraction torque, indicates that pedicle screws pre-filled with cement are superior for bone fixation over pedicle screws injected with cement.