Effects of the deformation and size of the upper airway on the deposition of aerosols.

Aerosol drug delivery in the human airway is significantly affected by the morphology and size of the airway. This work developed a CFD-DEM model to simulate and analyze air flow and powder dynamics in combined inhaler-airway systems with different degrees of airway deformation (non-deformed, 50%, and 75% deformed) and sizes (adult, 0.80, and 0.62 scaled). The airways were generated based on a regular airway constructed from the MRI images through finite element method (for deformed airways) or scaling-down (for smaller airways). The airways were connected to Turbuhaler® through a connector. The results showed that under the same flow rate, the variation in the airway geometry and size had a minimum impact on the flow field and powder deposition in the device and the connector. However, deformation caused more particle deposition in the deformed region. Notably, the airway with 50% deformation had the most particles passing through the airway with the largest particle sizes due to its lower air velocity in the deformed area. Reducing airway size resulted in more powder deposition on the airway, particularly at the pharynx and mouth regions. This was because, with the same flow rate, the flow velocity in the smaller airway was higher, causing more particle-wall collisions in the mouth and pharynx regions. More importantly, the deposition efficiency in the 0.62-scaled airway was significantly higher than the other two airways, highlighting the importance of the different administration of aerosol drugs for young children.

Chronoamperometric interrogation of an electrochemical aptamer-based sensor with tetrahedral DNA nanostructure pendulums for continuous biomarker measurements.

Tetrahedral DNA nanostructure (TDN) is highly promising in developing electrochemical aptamer-based (E-AB) sensors for biomolecular detection, owing to its inherit programmability, spatial orientation and structural robustness. However, current interrogation strategies applied for TDN-based E-AB sensors, including enzyme-based amperometry, voltammetry, and electrochemical impedance spectroscopy, either require complicated probe design or suffer from limited applicability or selectivity. In this study, a TDN pendulum-empowered E-AB sensor interrogated by chronoamperometry for reagent-free and continuous monitoring of a blood clotting enzyme, thrombin, was developed. TDN pendulums with extended aptamer sequences at three vertices were immobilized on a gold electrode via a thiolated double-stranded DNA (dsDNA) at the fourth vertex, and their motion is modulated by the bonding of target thrombin to aptamers. We observed a significantly amplified signalling output on our sensor based on the TDN pendulum compared to E-AB sensors modified with linear pendulums. Moreover, our sensor achieved highly selective and rapidly responsive measurement of thrombin in both PBS and artificial urine, with a wide dynamic range from 1 pM to 10 nM. This study shows chronoamperometry-enabled continuous biomarker monitoring on a sub-second timescale with a drift-free baseline, demonstrating a novel approach to accurately detect molecular dynamics in real time.

Numerical and experimental evaluation of nasopharyngeal aerosol administration methods in children with adenoid hypertrophy.

Administering aerosol drugs through the nasal pathway is a common early treatment for children with adenoid hypertrophy (AH). To enhance therapeutic efficacy, a deeper understanding of nasal drug delivery in the nasopharynx is essential. This study uses an integrated experimental, numerical modelling approach to investigate the delivery process of both the aerosol mask delivery system (MDS) and the bi-directional delivery system (BDS) in the pediatric nasal airway with AH. The combined effect of respiratory flow rates and particle size on delivery efficiency was systematically analyzed. The results showed that the nasopharyngeal peak deposition efficiency (DE) for BDS was approximately 2.25-3.73 times higher than that for MDS under low-flow, resting and high-flow respiratory conditions. Overall nasopharyngeal DEs for MDS were at a low level of below 16 %. For each respiratory flow rate, the BDS tended to achieve higher peak DEs (36.36 % vs 9.74 %, 37.80 % vs 14.01 %, 34.58 % vs 15.35 %) at smaller particle sizes (15 µm vs 17 µm, 10 µm vs 14 µm, 6 µm vs 9 µm). An optimal particle size exists for each respiratory flow rate, maximizing the drug delivery efficiency to the nasopharynx. The BDS is more effective in delivering drug aerosols to the nasal cavity and nasopharynx, which is crucial for early intervention in children with AH.

Understanding the effects of inhaler resistance on particle deposition behaviour - A computational modelling study.

BACKGROUND AND OBJECTIVE: Understanding the impact of inhaler resistance on particle transport and deposition in the human upper airway is essential for optimizing inhaler designs, thereby contributing to the enhancement of the therapeutic efficacy of inhaled drug delivery. This study demonstrates the potential effects of inhaler resistance on particle deposition characteristics in an anatomically realistic human oropharynx and the United States Pharmacopeia (USP) throat using computational fluid dynamics (CFD). METHOD: Magnetic resonance (MR) imaging was performed on a healthy volunteer biting on a small mockup inhaler mouthpiece. Three-dimensional geometry of the oropharynx and mouthpiece were reconstructed from the MR images. CFD simulations coupled with discrete phase modelling were conducted. Inhaled polydisperse particles under two different transient flow profiles with peak inspiratory flow rates (PIFR) of 30 L/min and 60 L/min were investigated. The effect of inhaler mouthpiece resistance was modelled as a porous medium by varying the initial resistance (Ri) and viscous resistance (Rv). Three resistance values, 0.02 kPa0.5minL-1, 0.035 kPa0.5minL-1 and 0.05 kPa0.5 minL-1, were simulated. The inhaler outlet velocity was set to be consistent across all models for both flow rate conditions to enable a meaningful comparison of models with different inhaler resistances. RESULT: The results from this study demonstrate that investigating the effect of inhaler resistance by solely relying on the USP throat model may yield misleading results. For the geometrically realistic oropharyngeal model, both the pressure and kinetic energy profiles at the mid-sagittal plane of the airway change dramatically when connected to a higher-resistance inhaler. In addition, the geometrically realistic oropharyngeal model appears to have a resistance threshold. When this threshold is surpassed, significant changes in flow dynamics become evident, which is not observed in the USP throat model. Furthermore, this study also reveals that the impact of inhaler resistance in a geometrically realistic throat model extends beyond the oral cavity and affects particle deposition downstream of the oral cavity, including the oropharynx region. CONCLUSION: Results from this study suggest that key mechanisms underpinning the working principles of inhaler resistance are intricately connected to their complex interaction with the pharynx geometry, which affects the local pressure, local variation in velocity and kinetic energy profile in the airway.

Numerical analysis of airflow and particle deposition in multi-fidelity designs of nasal replicas following nasal administration.

BACKGROUND AND OBJECTIVE: An improved understanding of flow behaviour and particle deposition in the human nasal airway is useful for optimising drug delivery and assessing the implications of pollutants and toxin inhalation. The geometry of the human nasal cavity is inherently complex and presents challenges and manufacturing constraints in creating a geometrically realistic replica. Understanding how anatomical structures of the nasal airway affect flow will shed light on the mechanics underpinning flow regulation in the nasal pharynx and provide a means to interpret flow and particle deposition data conducted in a nasal replica or model that has reduced complexity in terms of their geometries. This study aims to elucidate the effects of sinus and reduced turbinate length on nasal flow and particle deposition efficiencies. METHODS: A complete nasal airway with maxillary sinus was first reconstructed using magnetic resonance imaging (MRI) scans obtained from a healthy human volunteer. The basic model was then modified to produce a model without the sinus, and another with reduced turbinate length. Computational fluid dynamics (CFD) was used to simulate flow in the nasal cavity using transient flow profiles with peak flow rates of 15 L/min, 35 L/min and 55 L/min. Particle deposition was investigated using discrete phase modelling (DPM). RESULTS: Results from this study show that simplifying the nasal cavity by removing the maxillary sinus and curved sections of the meatus only has a minor effect on airflow. By mapping the spatial distribution of monodisperse particles (10 µm) in the three models using a grid map that consists of 30 grids, this work highlights the specific nasal airway locations where deposition efficiencies are highest, as observed within a single grid. It also shows that lower peak flow rates result in higher deposition differences in terms of location and deposition quantity, among the models. The highest difference in particle deposition among the three nasal models is ∼10%, and this is observed at the beginning of the middle meatus and the end of the pharynx, but is only limited to the 15 L/min peak flow rate case. Further work demonstrating how the outcome may be affected by a wider range of particle sizes, less specific to the pharmaceutical industries, is warranted. CONCLUSION: A physical replica manufactured without sections of the middle meatus could still be adequate in producing useful data on the deposition efficiencies associated with an intranasal drug formulation and its delivery device.

Challenges and current advances in in vitro biofilm characterization.

Biofilms are structured communities of bacterial cells encased in a self-produced polymeric matrix, which develop over time and exhibit temporal responses to stimuli from internal biological processes or external environmental changes. They can be detrimental, threatening public health and causing economic loss, while they also play beneficial roles in ecosystem health, biotechnology processes, and industrial settings. Biofilms express extreme heterogeneity in their physical properties and structural composition, resulting in critical challenges in understanding them comprehensively. The lack of detailed knowledge of biofilms and their phenotypes has deterred significant progress in developing strategies to control their negative impacts and take advantage of their beneficial applications. A range of in vitro models and characterization tools have been developed and used to study biofilm growth and, specifically, to investigate the impact of environmental and growth factors on their development. This review article discusses the existing knowledge of biofilm properties and explains how external factors, such as flow condition, surface, interface, and host factor, may impact biofilm growth. The limitations of current tools, techniques, and in vitro models that are currently used for biofilms are also presented.

Challenges in the Development and Application of Organ-on-Chips for Intranasal Drug Delivery Studies.

With the growing demand for the development of intranasal (IN) products, such as nasal vaccines, which has been especially highlighted during the COVID-19 pandemic, the lack of novel technologies to accurately test the safety and effectiveness of IN products in vitro so that they can be delivered promptly to the market is critically acknowledged. There have been attempts to manufacture anatomically relevant 3D replicas of the human nasal cavity for in vitro IN drug tests, and a couple of organ-on-chip (OoC) models, which mimic some key features of the nasal mucosa, have been proposed. However, these models are still in their infancy, and have not completely recapitulated the critical characteristics of the human nasal mucosa, including its biological interactions with other organs, to provide a reliable platform for preclinical IN drug tests. While the promising potential of OoCs for drug testing and development is being extensively investigated in recent research, the applicability of this technology for IN drug tests has barely been explored. This review aims to highlight the importance of using OoC models for in vitro IN drug tests and their potential applications in IN drug development by covering the background information on the wide usage of IN drugs and their common side effects where some classical examples of each area are pointed out. Specifically, this review focuses on the major challenges of developing advanced OoC technology and discusses the need to mimic the physiological and anatomical features of the nasal cavity and nasal mucosa, the performance of relevant drug safety assays, as well as the fabrication and operational aspects, with the ultimate goal to highlight the much-needed consensus, to converge the effort of the research community in this area of work.

Microfluidics assembly of inhalable liposomal ciprofloxacin characterised by an innovative in vitro pulmonary model.

Respiratory tract infections (RTIs) are reported to be the leading cause of death worldwide. Delivery of liposomal antibiotic nano-systems via the inhalation route has drawn significant interest in RTIs treatment as it can directly target the site of infection and reduces the risk of systemic exposure and side effects. Moreover, this formulation system can improve pharmacokinetics and biodistribution and enhance the activity against intracellular pathogens. Microfluidics is an innovative manufacturing technology that can produce nanomedicines in a homogenous and scalable way. The objective of this study was to evaluate the antibiofilm efficacy of two liposomal ciprofloxacin formulations with different vesicle sizes manufactured by using a 3D-printed microfluidic chip. Each formulation was characterised in terms of size, polydispersity index, charge and encapsulation. Moreover, the aerosolisation characteristics of the liposomal formulations were investigated and compared with free ciprofloxacin solution using laser diffraction and cascade impaction methods. The in vitro drug release was tested using the dialysis bag method. Furthermore, the drug transport and drug release studies were conducted using the alveolar epithelial H441 cell line integrated next-generation impactor in vitro model. Finally, the biofilm eradication efficacy was evaluated using a dual-chamber microfluidic in vitro model. Results showed that both liposomal-loaded ciprofloxacin formulations and free ciprofloxacin solution had comparable aerosolisation characteristics and biofilm-killing efficacy. The liposomal ciprofloxacin formulation of smaller vesicle size showed significantly slower drug release in the dialysis bag technique compared to the free ciprofloxacin solution. Interestingly, liposomal ciprofloxacin formulations successfully controlled the release of the drug in the epithelial cell model and showed different drug transport profiles on H441 cell lines compared to the free ciprofloxacin solution, supporting the potential for inhaled liposomal ciprofloxacin to provide a promising treatment for respiratory infections.

Quantifying Agglomerate-to-Wall Impaction in Dry Powder Inhalers.

PURPOSE: The probability of agglomerate-to-wall collision was quantified using a unique image processing technique applied to high-speed microscopic images. The study aimed to investigate the effects of flow rate and particle size on the percentage of colliding agglomerates detected within an in-house powder dispersion device. METHOD: The device consists of a swirl chamber and two tangential inlets in various configurations, designed to emulate the geometric features of commercial devices such as the Aerolizer® and Osmohaler®. The test cases were conducted with constant flow rates of 30 SLPM and 60 SLPM. Four powder samples were tested, including carrier Respitose® SV010 (median volume diameter 104 µm, span 1.7) and mannitol of three constituent primary particle sizes (3 µm, 5 µm and 7 µm; span 1.6 - 1.9). RESULTS: At the lower flow rate of 30 SLPM, collision frequencies were significantly different between powders of different constituent particle sizes, but the effects of powder properties diminished on increasing the flow rate to 60 SLPM. At the higher flow rate, all powders experienced a significant increase in the proportion of colliding particles. CONCLUSION: Analysis of collision events showed that the probability of collision for each agglomerate increased with agglomerate diameter and velocity. Experimental data of agglomerate-to-wall collision were utilised to develop a logistic regression model that can accurately predict collisions with various powders and flow rates.

In vitro interactions of aerosol formulations with human nasal epithelium using real-time monitoring of drug transport in a nasal mucosa-on-a-chip.

The current organ-on-chip platforms used for studying respiratory drug delivery are limited to the administration of drug solutions and suspensions, lacking the in vivo aerosol drug administration and aerosol interaction with the respiratory tract barrier. Moreover, they mostly rely on conventional assays that require sample collection and 'off the chip' analyses, which can be labor-intensive and costly. In this study, a human nasal epithelial mucosa (NEM)-on-a-chip is developed that enables the deposition of aerosolized nasal formulations while emulating realistic shear stresses (0.23 and 0.78 Pa), exerted to the inferior and middle turbinate of the human nasal cavity. Under these different dynamic conditions in the donor channel of the NEM-on-a-chip, the deposited dose of aerosols and particle size distributions varied. In addition, the increase in the shear stress to 0.78 Pa adversely affected the cells' viability, reflected by a 36.9 ± 5.4% reduction in the transepithelial electrical resistance. The epithelial transport profiles of aerosolized ibuprofen formulations under 0.23 Pa shear stress were successfully monitored in real-time by an electrochemical sensor embedded in the acceptor channel, where the NEM-on-a-chip was able to monitor the effect of permeation enhancer in the test formulation on the rate of drug transport. The novel NEM-on-a-chip can potentially be a promising physiologically relevant tool for reliable nasal aerosol testing in vitro.

Real-time in-situ electrochemical monitoring of Pseudomonas aeruginosa biofilms grown on air-liquid interface and its antibiotic susceptibility using a novel dual-chamber microfluidic device.

Biofilms are communities of bacterial cells encased in a self-produced polymeric matrix that exhibit high tolerance toward environmental stress. Despite the plethora of research on biofilms, most P. aeruginosa biofilm models are cultured on a solid-liquid interface, and the longitudinal growth characteristics of P. aeruginosa biofilm are unclear. This study demonstrates the real-time and noninvasive monitoring of biofilm growth using a novel dual-chamber microfluidic device integrated with electrochemical detection capabilities to monitor pyocyanin (PYO). The growth of P. aeruginosa biofilms on the air-liquid interface (ALI) was monitored over 48 h, and its antibiotic susceptibility to 6 h exposure of 50, 400, and 1600 µg/ml of ciprofloxacin solutions was analyzed. The biofilm was treated directly on its surface and indirectly from the substratum by delivering the CIP solution to the top or bottom chamber of the microfluidic device. Results showed that P. aeruginosa biofilm developed on ALI produces PYO continuously, with the PYO production rate varying longitudinally and peak production observed between 24 and 30 h. In addition, this current study shows that the amount of PYO produced by the ALI biofilm is proportional to its viable cell numbers, which has not been previously demonstrated. Biofilm treated with ciprofloxacin solution above 400 µg/ml showed significant PYO reduction, with biofilms being killed more effectively when treatment was applied to their surfaces. The electrochemical measurement results have been verified with colony-forming unit count results, and the strong correlation between the PYO electrical signal and the viable cell number highlights the usefulness of this approach for fast and low-cost ALI biofilm study and antimicrobial tests.

Simulating the effect of individual upper airway anatomical features on drug deposition.

This study aims to systematically isolate different anatomical features of the human pharynx with the goal to investigate their independent influence on airflow dynamics and particle deposition characteristics in a geometrically realistic human airway. Specifically, the effects of the uvula, epiglottis and soft palate on drug particle deposition are studied systematically, by carefully removing each of these anatomical features from reconstructed models based on MRI data and comparing them to a benchmark realistic airway model. Computational Fluid Dynamics using established turbulence models is employed to simulate the transport of mono-dispersed particles (3 µm) in the airway at two flow-rates. The simulations suggest three findings: 1) widening the space between the oral cavity and oropharynx and where the soft palate is situated leads to the most dramatic reduction in drug deposition in the upper airway; 2) exclusion of the uvula and epiglottis: a) affects flow dynamics in the airway; b) alters regional deposition behaviour; c) does not significantly affect the total number of particles deposited in the pharynx; and 3) the space adjacent to the soft palate is a key determinant for aerosol deposition in the extrathoracic region and is related to mechanisms of flow acceleration, diversion and recirculation.

A review of upper airway physiology relevant to the delivery and deposition of inhalation aerosols.

Developing effective oral inhaled drug delivery treatment strategies for respiratory diseases necessitates a thorough knowledge of the respiratory system physiology, such as the differences in the airway channel's structure and geometry in health and diseases, their surface properties, and mechanisms that maintain their patency. While respiratory diseases, such as chronic obstructive pulmonary disease (COPD) and asthma and their implications on the lower airways have been the core focus of most of the current research, the role of the upper airway in these diseases is less known, especially in the context of inhaled drug delivery. This is despite the fact that the upper airway is the passageway for inhaled drugs to be delivered to the lower airways, and their replicas are indispensable in current standards, such as the cascade impactor experiments for testing inhaled drug delivery technology. This review provides an overview of upper airway collapsibility and their mechanical properties, the effects of age and gender on upper airway geometry, and surface properties. The review also discusses how COPD and asthma affect the upper airway and the typical inhalation flow characteristics exhibited by the patients with these diseases.

Application of Micro-Engineered Kidney, Liver, and Respiratory System Models to Accelerate Preclinical Drug Testing and Development.

Developing novel drug formulations and progressing them to the clinical environment relies on preclinical in vitro studies and animal tests to evaluate efficacy and toxicity. However, these current techniques have failed to accurately predict the clinical success of new therapies with a high degree of certainty. The main reason for this failure is that conventional in vitro tissue models lack numerous physiological characteristics of human organs, such as biomechanical forces and biofluid flow. Moreover, animal models often fail to recapitulate the physiology, anatomy, and mechanisms of disease development in human. These shortfalls often lead to failure in drug development, with substantial time and money spent. To tackle this issue, organ-on-chip technology offers realistic in vitro human organ models that mimic the physiology of tissues, including biomechanical forces, stress, strain, cellular heterogeneity, and the interaction between multiple tissues and their simultaneous responses to a therapy. For the latter, complex networks of multiple-organ models are constructed together, known as multiple-organs-on-chip. Numerous studies have demonstrated successful application of organ-on-chips for drug testing, with results comparable to clinical outcomes. This review will summarize and critically evaluate these studies, with a focus on kidney, liver, and respiratory system-on-chip models, and will discuss their progress in their application as a preclinical drug-testing platform to determine in vitro drug toxicology, metabolism, and transport. Further, the advances in the design of these models for improving preclinical drug testing as well as the opportunities for future work will be discussed.

Understanding the effects of aerodynamic and hydrodynamic shear forces on Pseudomonas aeruginosa biofilm growth.

Biofilms are communities of bacterial cells encased in a self-produced polymeric matrix and exhibit high tolerance towards environmental stress. Despite the plethora of research on biofilms, most biofilm models are produced using mono-interface culture in static flow conditions, and knowledge of the effects of interfaces and mechanical forces on biofilm development remains fragmentary. This study elucidated the effects of air-liquid (ALI) or liquid-liquid (LLI) interfaces and mechanical shear forces induced by airflow and hydrodynamic flow on biofilm growing using a custom-designed dual-channel microfluidic platform. Results from this study showed that comparing biofilms developed under continuous nutrient supply and shear stresses free condition to those developed with limited nutrient supply, ALI biofilms were four times thicker, 60% less permeable, and 100 times more resistant to antibiotics, while LLI biofilms were two times thicker, 20% less permeable, and 100 times more resistant to antibiotics. Subjecting the biofilms to mechanical shear stresses affected the biofilm structure across the biofilm thickness significantly, resulting in generally thinner and denser biofilm compared to their controlled biofilm cultured in the absence of shear stresses, and the ALI and LLI biofilm's morphology was vastly different. Biofilms developed under hydrodynamic shear stress also showed increased antibiotic resistance. These findings highlight the importance of investigating biofilm growth and its mechanisms in realistic environmental conditions and demonstrate a feasible approach to undertake this study using a novel platform.

From laminar to turbulent flow in a dry powder inhaler: The effect of simple design modifications.

In order to better understand powder dispersion in dry powder inhaler (DPI) devices, a new powder disperser was designed, which uses flow modifiers to alter powder fluidization behavior so as to physically replicate various flow conditions observed in a range of commercial DPIs. The influence of these modifiers on the performance of the DPI was analyzed for flowrates progressing from laminar (15 L/min) to transitional (30 L/min), and finally turbulent flow regimes (60 L/min) in the device. The aerosol performance of the disperser was measured using a Next Generation Impactor. For flowrate in the laminar regime, powder evacuation from the disperser was generally insufficient (<30%), which was increased to >85% when the device was operated in the turbulent flow regime. In contrast, the highest fine particle fraction (FPF) and lowest throat deposition were achieved when operating in the transitional flow regime. The FPF could be increased further by applying flow modifications such as narrowing the air passage before the powder pocket, inducing localized turbulence (by a grid) near the powder pocket, and by changing the loading position of the powder. Flow modifiers had the most noticeable effect under a laminar flow regime, however, the device operated most efficiently under a transitional flow regime.

Effects of respiratory rate on the fluid mechanics of a reconstructed upper airway.

This study aims to utilise particle image velocimetry (PIV) techniques to investigate the time-dependant effects of respiratory rate in the extrathoracic airway, to show how they affect the flow field developed. There has been limited validation of computational fluid dynamics (CFD) models using experimental setups. Furthermore, the large majority of existing CFD models focus on rigid airways, not accounting for active deformation through the breathing cycle. Experiments were carried out to expand upon Zhao et al.'s previous study, in which a single respiratory rate was investigated. This studied utilised a transient, sinusoidal flow profile with two respiratory rates of 10 breaths per minute (BPM) and 25 BPM, both achieving a maximum flow rate correlating to 5 L/min in air to simulate tidal breathing. Results from this study showed that respiratory rate had the greatest influence near the onset of the inspiratory and expiratory manoeuvres, with the higher respiratory rate homogenising later in the cycle. It was shown that airway deformation at the level of the soft palate homogenised flow downstream of the deformation which resulted in a lower peak magnitude velocity for approximately 40% of the cycle at the level of the epiglottis, when compared to the rigid airway model.

An adaptable microreactor to investigate the influence of interfaces on Pseudomonas aeruginosa biofilm growth.

Biofilms are ubiquitous and notoriously difficult to eradicate and control, complicating human infections and industrial and agricultural biofouling. However, most of the study had used the biofilm model that attached to solid surface and developed in liquid submerged environments which generally have neglected the impact of interfaces. In our study, a reusable dual-chamber microreactor with interchangeable porous membranes was developed to establish multiple growth interfaces for biofilm culture and test. Protocol for culturing Pseudomonas aeruginosa (PAO1) on the air-liquid interface (ALI) and liquid-liquid interface (LLI) under static environmental conditions for 48 h was optimized using this novel device. This study shows that LLI model biofilms are more susceptible to physical disruption compared to ALI model biofilm. SEM images revealed a unique "dome-shaped" microcolonies morphological feature, which is more distinct on ALI biofilms than LLI. Furthermore, the study showed that ALI and LLI biofilms produced a similar amount of extracellular polymeric substances (EPS). As differences in biofilm structure and properties may lead to different outcomes when using the same eradication approaches, the antimicrobial effect of an antibiotic, ciprofloxacin (CIP), was chosen to test the susceptibility of a 48-h-old P. aeruginosa biofilms grown on ALI and LLI. Our results show that the minimum biofilm eradication concentration (MBEC) of 6-h CIP exposure for ALI and LLI biofilms is significantly different, which are 400 µg/mL and 200 µg/mL, respectively. These results highlight the importance of growth interface when developing more targeted biofilm management strategies, and our novel device provides a promising tool that enables manipulation of realistic biofilm growth. KEY POINTS: • A novel dual-chamber microreactor device that enables the establishment of different interfaces for biofilm culture has been developed. • ALI model biofilms and LLI model biofilms show differences in resistance to physical disruption and antibiotic susceptibility.

Effect of inflow conditioning for dry powder inhalers.

The transport of pharmaceutical dry powder inside an optically accessible inhaler-like device is studied using both macro- and microscopic high-speed imaging. The investigation aims to systematically study the effect of inflow modifications on the dispersion characteristics of agglomerates inside a dry powder inhaler (DPI) geometry. An inhaler device was designed with geometrical features akin to commercial inhalers used in the current market and research oriented inhalers such as the Twincer®: two offset inlet channels (one with a powder pocket), a clockwise swirling chamber and a single outlet channel. At the device outlet, a vacuum pump was fitted with an actuator and calibrated to achieve a steady state inhalation with a peak flowrate of 85 and 125 L/min. Airflow conditions at the intake of the device were strategically perturbed in order to induce powder fluidisation and dispersion using turbulence grids and through physically obstructing channel streams in order to achieve changes in flow behaviour (e.g., flow separation). Complete fluidisation of the powder bed was observed with image processing enabling statistics on de-agglomerated fragment size and velocity. A range of behaviour was noted including local turbulence through introduction of a grid, bimodal fragment size behaviour for cohesive mannitol powder, as well as introduction of low velocity zones in the device through flow splitting. The geometry enables simple systematic study of inflow conditions into a DPI-like device with the data being useful for study of a given powder formulation (mannitol) and validation of computational models.

Real-time quantitative monitoring of in vitro nasal drug delivery by a nasal epithelial mucosa-on-a-chip model.

OBJECTIVES: A human nasal epithelial mucosa (NEM) on-a-chip is developed integrated with a novel carbon nanofibers-modified carbon electrode for real-time quantitative monitoring of in vitro nasal drug delivery. The integration of platinum electrodes in the chip also enables real-time measurement of transepithelial electrical resistance (TEER). METHODS: The air-liquid interface culture of nasal epithelial RPMI 2650 cells in the NEM-on-a-chip was optimized to mimic the key functional characteristics of the human nasal mucosa. The epithelial transport of ibuprofen in the NEM-on-a-chip was electrochemically monitored in real-time under static and physiologically realistic dynamic flow conditions. RESULTS: The NEM-on-a-chip mimics the mucus production and nasal epithelial barrier function of the human nasal mucosa. The real-time drug quantification by the NEM-on-a-chip was validated versus the high-performance liquid chromatography method. The drug transport rate monitored in the NEM-on-a-chip was influenced by the flow in the bottom compartment of the chip, highlighting the importance of emulating the dynamic in vivo condition for nasal drug transport studies. CONCLUSION: This novel NEM-on-a-chip can be a low-cost and time-efficient alternative to the costly laborious conventional techniques for in vitro nasal drug transport assays. Importantly, its dynamic microenvironment enables conducting nasal drug transport tests under physiologically relevant dynamic conditions.