Microbial bio-based plastics from olive-mill wastewater: Generation and properties of polyhydroxyalkanoates from mixed cultures in a two-stage pilot scale system.

The operational efficiency of a two stage pilot scale system for polyhydroxyalkanoates (PHAs) production from three phase olive oil mill wastewater (OMW) was investigated in this study. A mixed anaerobic, acidogenic culture derived from a municipal wastewater treatment plant, was used in the first stage, aiming to the acidification of OMW. The effluent of the first bioreactor that was operated in continuous mode, was collected in a sedimentation tank in which partial removal of the suspended solids was taking place, and was then forwarded to an aerobic reactor, operated in sequential batch mode under nutrient limitation. In the second stage an enriched culture of Pseudomonas sp. was used as initial inoculum for the production of PHAs from the acidified waste. Clarification of the acidified waste, using aluminium sulphate which causes flocculation and precipitation of solids, was also performed, and its effect on the composition of the acidified waste as well as on the yields and properties of PHAs was investigated. It was shown that clarification had no significant qualitative or quantitative effect on the primary carbon sources, i.e. short chain fatty acids and residual sugars, but only on the values of total suspended solids and total chemical oxygen demand of the acidified waste. The type and thermal characteristics of the produced PHAs were also similar for both types of feed. However the clarification of the waste seemed to have a positive impact on final PHAs yield, measured as gPHAs/100g of VSS, which reached up to 25%. Analysis of the final products via nuclear magnetic resonance spectroscopy revealed the existence of 3-hydroxybutyrate (3HB) and 3-hydroxyoctanoate (HO) units, leading to the conclusion that the polymer could be either a blend of P3HB and P3HO homopolymers or/and the 3HB-co-3HO co-polymer, an unusual polymer occurring in nature with advanced properties.

Vitronectin absorbed on nanoparticles mediate cell viability/proliferation and uptake by 3T3 Swiss albino mouse fibroblasts: in vitro study.

We study the interaction of 3T3 Swiss albino mouse fibroblasts with polymeric nanoparticles (NPs) and investigate cellular behaviour in terms of viability/cytotoxicity, cell cycle, NPs uptake, MAP kinase (ERK1/2), and focal adhesion kinase (FAK) activation. After incubation of NPs with cell culture media, western blot analysis showed that Vitronectin is retained by NPs, while Fibronectin is not detected. From cytotoxicity studies (MTT and BrdU methods) an LD50 of about 1.5 mg/mL results for NPs. However, NPs in the range 0.01-0.30 mg/mL are able to trigger a statistically significant increase in proliferation and cell cycle progression in dose and time depending manner. Also, biochemical evaluation of ERK1/2 and FAK clearly shows an increasing phosphorylation in a dose and time depending manner. Finally, we found by transmission electron microscopy that NPs are internalised by cells. Competitively blocking VN-integrin receptors with echistatin (1 µg/mL) results in a decrease of viability/proliferation, cell cycle progression, cellular uptake, and FAK/ERK activation showing the involvement of Vitronectin receptors in signal transduction. In conclusion, our results show that cell surface NPs interactions are mediated by absorbed plasma proteins (i.e., Vitronectin) that represent an external stimuli, switched to the nucleus by FAK enzyme, which in turn modulate fibroblasts viability/proliferation.

Development of a bioactive glass fiber reinforced starch-polycaprolactone composite.

For bone regeneration and repair, combinations of different materials are often needed. Biodegradable polymers are often combined with osteoconductive materials, such as bioactive glass (BaG), which can also improve the mechanical properties of the composite. The aim of this work was to develop and characterize BaG fiber reinforced starch-poly-epsilon-caprolactone (SPCL) composite. Sheets of SPCL (30/70 wt %) were produced using single-screw extrusion. They were then cut and compression-molded in layers with BaG fibers to form composite structures with different combinations. Mechanical and degradation properties of the composites were studied. The actual amount of BaG in the composites was determined using combustion tests. Initial mechanical properties of the reinforced composites were at least 50% better than the properties of the nonreinforced specimens. However, the mechanical properties of the composites after 2 weeks of hydrolysis were comparable to those of the nonreinforced samples. During the 6 weeks hydrolysis the mass of the composites had decreased only by about 5%. The amount of glass in the composites remained as initial for the 6-week period of hydrolysis. In conclusion, it is possible to enhance initial mechanical properties of SPCL by reinforcing it with BaG fibers. However, mechanical properties of the composites are typical for bone fillers and strength properties need to be further improved for allowing more demanding bone applications.

Biodegradable nanomats produced by electrospinning: expanding multifunctionality and potential for tissue engineering.

With increasing interest in nanotechnology, development of nanofibers (n-fibers) by using the technique of electrospinning is gaining new momentum. Among important potential applications of n-fiber-based structures, scaffolds for tissue-engineering represent an advancing front. Nanoscaffolds (n-scaffolds) are closer to natural extracellular matrix (ECM) and its nanoscale fibrous structure. Although the technique of electrospinning is relatively old, various improvements have been made in the last decades to explore the spinning of submicron fibers from biodegradable polymers and to develop also multifunctional drug-releasing and bioactive scaffolds. Various factors can affect the properties of resulting nanostructures that can be classified into three main categories, namely: (1) Substrate related, (2) Apparatus related, and (3) Environment related factors. Developed n-scaffolds were tested for their cytocompatibility using different cell models and were seeded with cells for to develop tissue engineering constructs. Most importantly, studies have looked at the potential of using n-scaffolds for the development of blood vessels. There is a large area ahead for further applications and development of the field. For instance, multifunctional scaffolds that can be used as controlled delivery system do have a potential and have yet to be investigated for engineering of various tissues. So far, in vivo data on n-scaffolds are scarce, but in future reports are expected to emerge. With the convergence of the fields of nanotechnology, drug release and tissue engineering, new solutions could be found for the current limitations of tissue engineering scaffolds, which may enhance their functionality upon in vivo implantation. In this paper electrospinning process, factors affecting it, used polymers, developed n-scaffolds and their characterization are reviewed with focus on application in tissue engineering.

Development of diclofenac sodium releasing bio-erodible polymeric nanomats.

Application of nanofiber-based nanomats in medicine is attractive and thanks to the 3D nanostructure and the high surface to volume ratio they are excellent for local controlled drug delivery. The use of bioactive bioerodible polymers for developing drug delivery nanomats may allow for drug release and targeting control. Objective of the current study was to evaluate the suitability of bioerodible polymeric material based on n-butyl hemiester of [poly(maleic anhydride-alt-2-methoxyethyl vinyl ether)] (PAM14) for the preparation of nanomats for controlled administration of anti-inflammatory, diclofenac sodium (DS) drug. Samples were prepared using different polymer concentrations (5-10%) in either ethanol or acetic acid as solvent. Morphology was investigated by using scanning electron microscopy (SEM). Thermal analysis such as differential scanning calorimetry (DSC) was performed to detect effect on polymer arrangement. DS localization in electrospun nanomats was evaluated by using electron back scattering microanalysis, based on the detection of chlorine, and drug release kinetics was assessed using UV-Vis. Average fiber diameter resulted in the range of 100 nm to 1.0 microm and a homogeneous distribution of the loaded drug into the fibers was observed. The DS release was immediate and despite the preliminary nature of the performed electrospinning experiments, the achieved results appear promising for the future development of a novel system for the controlled and targeted administration of drug and active agent.

Biodegradable nanomats produced by electrospinning: expanding multifunctionality and potential for tissue engineering.

With increasing interest in nanotechnology, development of nanofibers (n-fibers) by using the technique of electrospinning is gaining new momentum. Among important potential applications of n-fiber-based structures, scaffolds for tissue-engineering represent an advancing front. Nanoscaffolds (n-scaffolds) are closer to natural extracellular matrix (ECM) and its nanoscale fibrous structure. Although the technique of electrospinning is relatively old, various improvements have been made in the last decades to explore the spinning of submicron fibers from biodegradable polymers and to develop also multifunctional drug-releasing and bioactive scaffolds. Various factors can affect the properties of resulting nanostructures that can be classified into three main categories, namely: (1) Substrate related, (2) Apparatus related, and (3) Environment related factors. Developed n-scaffolds were tested for their cytocompatibility using different cell models and were seeded with cells for to develop tissue engineering constructs. Most importantly, studies have looked at the potential of using n-scaffolds for the development of blood vessels. There is a large area ahead for further applications and development of the field. For instance, multifunctional scaffolds that can be used as controlled delivery system do have a potential and have yet to be investigated for engineering of various tissues. So far, in vivo data on n-scaffolds are scarce, but in future reports are expected to emerge. With the convergence of the fields of nanotechnology, drug release and tissue engineering, new solutions could be found for the current limitations of tissue engineering scaffolds, which may enhance their functionality upon in vivo implantation. In this paper electrospinning process, factors affecting it, used polymers, developed n-scaffolds and their characterization are reviewed with focus on application in tissue engineering.

Ubidecarenone nanoemulsified composite systems.

The nanoemulsified composite (NEC) delivery system is a patented technology based on the incorporation of a double microemulsion into microporous carrier. This approach was applied on the very water insoluble ubidecarenone drug. The resulting composite powder showed good technological properties such as flowability; also good stability was evidentiated, with size of the nano-droplets released from the systems maintained equal to the starting size also after a long storage. Furthermore very good biopharmaceutical properties were originated, with water solubility concentrations up to 50-fold higher than pure ubidecarenone and oral absorption in rats up to three-fold greater than standard commercial products in terms of plasma levels and AUC.

Ageing and oxidative stress: a role for dolichol in the antioxidant machinery of cell membranes?

Dolichol is a polyprenol compound broadly distributed in membranes, biosynthetized by the general isoprenoid pathway from acetate via mevalonate and farnesyl pyrophosphate. Dolichol lays inside the membrane between the two leaflets of the lipid bilayer very close to the tail of phospholipid fatty acids. No definite catabolic pathways for this molecule have yet been identified. Evidence is produced that dolichol levels increase dramatically with increasing age; that anti-ageing caloric restriction retards this age-associated change; that dolichol may act as a radical scavenger of peroxidized lipids belonging to the cell membranes. In view of the polyunsaturated fatty acids (PUFA), dolichol and Vitamin E location and stechiometry, it is proposed that molecules might interact each-other to form a highly matched free-radical-transfer chain, whose malfunctioning might be involved in statin toxicity and neurodegenerative diseases.

Removal of viruscide agents by using styrenic resins.

Strong and weak anionic polystyrene/divinylbenzene ion exchange resins were investigated both as iodophores and as iodine/iodide ion removal agents in blood disinfection applications. Resin-iodine complexes were prepared, but there was no significant iodine release observed in either distilled water or isotonic saline solution. However, all ion-exchange resin were able to remove almost quantitatively both iodine and iodide ions from water solutions. Cross-linked styrene/divinylbenzene resins are excellent polyaromatic viruscide adsorbents, although their hydrophobicity is responsible for poor wettability in physiologi-cal fluids. Surface modification with hydrophilic reagents appeared a promising strategy to overcome this drawback. A Merrifield-type chloromethylated resin and a highly cross-linked mesoporous resin (Lewatit 1064) with a large surface area and content of unreacted vinyl groups were selected as starting materials. The Merrifield resin was modified by the reaction of the pendant chloromethyl groups with triethyleneglycol, tetraethyleneglycol and â -cyclodextrin. The conversion of Lewatit double bonds into hydrophilic moieties was attempted by the radical grafting of N-vinyl-2-pyrrolidinone (NVP), maleic anhydride (MAn), 2-hydroxyethyl methacrylate, acrylamide (AAm) and different poly(ethyleneglycol) (PEG) methacrylates. The addition of 2-mer-captoethanol (2ME) and epoxidation were also investigated. The modified Merrifield resins demonstrated very low efficiency in acridine viruscide uptake, in spite of the large increase in both wettability and water uptake. On the other hand, all modified Lewatit samples removed rapidly and almost quantitatively the viruscide from aqueous solutions, although only a few samples resulted in being very hydrophilic. In all cases, hydrophilicity and viruscide adsorbing capacity were maintained after heating at 180 degrees C to simulate pyrogen elimination.

Nanoparticle systems for the targeted release of active principles of proteic nature.

The preparation and characterization of nanoparticles based on biodegradable/bioerodible polymers is reported. They have been designed for the controlled-targeted release of proteic drugs such as alpha-interferon and for the release of active principles in tissue engineering. The amenability of some of the prepared polymeric matrices to be used in the fabrication of micro and nano patterned scaffolds is also described.

Composite films based on biorelated agro-industrial waste and poly(vinyl alcohol). Preparation and mechanical properties characterization.

As a part of an ongoing project on the production of composite materials based on poly(vinyl alcohol) (PVA) and polymeric materials from renewable resources, the present paper reports on the incorporation of agricultural waste materials as organic fillers in a film matrix based on PVA as continuous phase. In this study lignocellulosic fibers byproducts, derived from sugar cane (SC) and apple (AP) and orange (OR) fruit juice extraction, were cast from PVA aqueous solutions. The effect of fiber type and composition on the relative properties of cast films was evaluated and compared. OR resulted to be suitable for blending in higher amounts by weight than SC and AP. Glycerol and urea were added as plasticizing agents and were observed to be effective in giving flexible films. Additionally, cornstarch was added to further increase the composition of polymers from renewable resources in cost-effective and ecoefficient composite film formulations. The prepared films resulted sensitive to moisture and water. To reduce water sensitivity, hexamethoxymethylmelamine (HMMM) was tested as a cross-linking agent for the present composite formulations. Cross-linked films exhibited significant improvement in water-resistance that can be taken as a tuneable structural feature for customized applications. The mechanical properties of the prepared composite films (elongation at break, tensile strength, Young modulus) were found to be dependent upon the nature and content of the filler and on environmental conditions.

Gelatin-based blends and composites. Morphological and thermal mechanical characterization.

Gelatin, a natural macromolecular proteic material from renewable resources, is widely used in many industrial applications. In this study gelatin scraps, deriving from pharmaceutical capsule productions, were turned into films by casting water solutions or suspensions producing flexible and consistent films. Gelatin was blended with poly(vinyl alcohol), a biodegradable synthetic polymer, in order to improve mechanical properties in the films. Gelatin was blended also with sugar cane bagasse, a lignin cellulosic waste from sugar cane processing. These blends showed good interface adhesion between gelatin and sugar cane fibers and mechanical properties of practical interest for up to 20% of sugar cane content by weight. Glutaraldehyde was used in different amounts as a cross-linking agent increasing elongation at break especially for amount above 1%. Morphology, thermal, thermomechanical, and mechanical properties of the samples were investigated by scanning electron microscopy (SEM), thermal gravimetric analysis (TGA), differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), and tensile tests, respectively. Cast films presented thermal and mechanical properties, which make them good candidates as biodegradable self-fertilizing mulching films.

Modelling of the 3-D structure of IFN-alpha-k and characterization of its surface molecular properties.

The 3-D structure of IFN-alpha-k (one of the alpha-interferon family) was constructed and optimized by molecular modelling starting from the X-ray structure of IFN-beta. The molecular surface of the optimized 3-D structure of IFN-alpha-k was then evaluated and characterized for its hydrophobicity/hydrophilicity. The structure of IFN-alpha-k was completed with its first segment (23 amino acid residues) called signal peptide. The 3-D structure of this segment was predicted to be in helical form bonded to the core by one loop. It was found that the complete structure of IFN-alpha-k can exist in at least two main conformations as far as the orientation of the signal peptide is concerned, i.e. in the open form (in which the signal peptide is directed outward of the 'body' of the molecule) and the closed form (where the signal peptide is aligned with the body). The relative stability of these forms strongly depends on the stabilization by the environment (e.g. by solvation) due to the prevailing hydrophilicity of the body and hydrophobic character of the signal peptide.

New hydrophilic polyesters and related polymers as bioerodible polymeric matrices.

A survey is reported on our activity performed in the last few years on the preparation of new synthetic and semisynthetic polymeric materials endowed with bioerodible-biodegradable characteristics and designed for applications in the practice of controlled release of active principles of pharmaceutical and agrochemical significance. The presentation of the results will be arranged into the following sections: (1) hydroxyl containing polyesters, that comprise polymerization products based on racemic and optically active glyceric acid, or attained by polyaddition reactions among cyclic anhydrides, including also carbon dioxide, with monoglycidyl ethers of reversibly protected polyols. In this class are also presented the related polyhydroxylated systems obtained by selective grafting functional epoxides on cyclodextrins. (2) Bioerodible carboxyl containing polymeric systems as derived from the alternating copolymerization of maleic anhydride with alkyl vinyl ethers followed by partial esterification of maleic anhydride groups. (3) Linear and cross-linked functional polymers of synthetic and semisynthetic origin with hydrogel forming capability. Typical examples of their applications in the release of drugs and phytodrugs are also presented.

Vehicle effects in ophthalmic bioavailability: an evaluation of polymeric inserts containing pilocarpine.

A series of polymeric ophthalmic inserts containing pilocarpine were formulated with four different types of polyvinyl alcohol, PVA, and two types of hydroxypropylcellulose. Pilocarpine was present as the nitrate, or as the salt with polyacrylic acid, PAA. In-vivo miosis vs time experiments on albino rabbits, showed that all inserts increased significantly the bioavailability of pilocarpine, with respect to a standard solution of pilocarpine nitrate. Two PVA inserts, containing the PAA-salt of pilocarpine, were particularly effective. The preparations were also submitted to in-vitro release tests and to differential scanning calorimetry, to ascertain the release mechanism, and to verify, via the thermal behaviour, possible interactions between drug and polymers. The chemical and physiochemical factors, most likely to influence the ophthalmic bioavailability of pilocarpine from the present preparations, are briefly reviewed.

Evaluation of new membranes for hemodialysis: preliminary studies with a polycarbonate membrane.

A synthetic polycarbonate (PC) membrane supplied by C.R. Bard Inc. was assessed as to its clinical usefulness and suitability to regular use with artificial kidney. The permeability of the PC membrane to 11 solutes of increasing molecular volumes (Na+, Ca++, K+, Cl-, HPO4-, urea, creatinine, uric acid, glucose, BSP, cyanocobalamine) was measured in vitro by rotating dialysis cells, as compared to that of Cuprophan PT 150. The evaluation of the PC membrane in vivo was carried out during a regular hemodialytic treatment in 5 patients using a Kiil dialyzer. The dialysance of 6 solutes (HPO4-, urea, creatinine, uric acid, hypaque, cyanocobalamine) across the PC membrane was measured at 200 ml/min blood flow rate. Both in vitro and in vivo the PC membrane showed permeability and dialysance coefficients to small molecules approximately the same than standard PT 150; the ultrafiltration rate of the PC membrane was also superimposable to that of PT 150. On the contrary, larger molecules were removed much more efficiently by the polycarbonate membrane than by PT 150. These data suggest that the membrane evaluated in this study possesses some peculiar features which could possibly result in an improvement of the quality of regular hemodialysis.