Measurement of Thermal Stress by X-ray Nano-Diffraction in (111)-Oriented Nanotwinned Cu Bumps for Cu/SiO2 Hybrid Joints.

X-ray nanodiffraction was used to measure the thermal stress of 10 µm nanotwinned Cu bumps in Cu/SiO2 hybrid structures at -55 °C, 27 °C, 100 °C, 150 °C, and 200 °C. Bonding can be achieved without externally applied compression. The X-ray beam size is about 100 nm in diameter. The Cu bump is dominated by (111) oriented nano-twins. Before the hybrid bonding, the thermal stress in Cu bumps is compressive and remains compressive after bonding. The average stress in the bonded Cu joint at 200 °C is as large as -169.1 MPa. In addition, using the strain data measured at various temperatures, one can calculate the effective thermal expansion coefficient (CTE) for the 10 µm Cu bumps confined by the SiO2 dielectrics. This study reports a useful approach on measuring the strain and stress in oriented metal bumps confined by SiO2 dielectrics. The results also provide a deeper understanding on the mechanism of hybrid bonding without externally applied compression.

Polymer Nanoparticles Applied in the CMP (Chemical Mechanical Polishing) Process of Chip Wafers for Defect Improvement and Polishing Removal Rate Response.

Chemical mechanical planarization (CMP) is a wafer-surface-polishing planarization technique based on a wet procedure that combines chemical and mechanical forces to fully flatten materials for semiconductors to be mounted on the wafer surface. The achievement of devices of a small nano-size with few defects and good wafer yields is essential in enabling IC chip manufacturers to enhance their profits and become more competitive. The CMP process is applied to produce many IC generations of nanometer node, or those of even narrower line widths, for a better performance and manufacturing feasibility. Slurry is a necessary supply for CMP. The most critical component in slurry is an abrasive particle which affects the removal rates, uniformity, defects, and removal selectivity for the materials on the wafer surface. The polishing abrasive is the source of mechanical force. Conventional CMP abrasives consist of colloidal silica, fume silica or other inorganic polishing particles in the slurries. We were the first to systematically study nanoparticles of the polymer type applied in CMP, and to compare traditional inorganic and polymer nanoparticles in terms of polishing performance. In particular, the polymer nanoparticle size, shape, solid content dosing ratio, and molecular types were examined. The polishing performance was measured for the polishing removal rates, total defect counts, and uniformity. We found that the polymer nanoparticles significantly improved the total defect counts and uniformity, although the removal rates were lower than the rates obtained using inorganic nanoparticles. However, the lower removal rates of the polymer nanoparticles are acceptable due to the thinner film materials used for smaller IC device nodes, which may be below 10 nm. We also found that the physical properties of polymer nanoparticles, in terms of their size, shape, and different types of copolymer molecules, cause differences in the polishing performance. Meanwhile, we used statistical analysis software to analyze the data on the polishing removal rates and defect counts. This method helps to determine the most suitable polymer nanoparticle for use as a slurry abrasive, and improves the reliability trends for defect counts.

Low-Temperature Cu/SiO2 Hybrid Bonding with Low Contact Resistance Using (111)-Oriented Cu Surfaces.

We adopted (111)-oriented Cu with high surface diffusivity to achieve low-temperature and low-pressure Cu/SiO2 hybrid bonding. Electroplating was employed to fabricate arrays of Cu vias with 78% (111) surface grains. The bonding temperature can be lowered to 200 °C, and the pressure is as low as 1.06 MPa. The bonding process can be accomplished by a 12-inch wafer-to-wafer scheme. The measured specific contact resistance is 1.2 × 10-9 Ω·cm2, which is the lowest value reported in related literature for Cu-Cu joints bonded below 300 °C. The joints possess excellent thermal stability up to 375 °C. The bonding mechanism is also presented to provide more understanding on hybrid bonding.

Fabrication and characteristics of highly [Formula: see text]-oriented nanotwinned Au films.

Fine grained and nanotwinned Au has many excellent properties and is widely used in electronic devices. We have fabricated [Formula: see text] preferred-oriented Au thin films by DC plating at 5 mA/cm2. Microstructure analysis of the films show a unique fine grain structure with a twin formation. Hardness tests performed on electroplated [Formula: see text] Au films show a hardness 47% greater than random and untwinned Au. We then achieved direct bonding between two Au [Formula: see text] surfaces operating at 200 °C for an hour in a vacuum oven. The highly-oriented [Formula: see text] nanotwinned Au films could be an ideal material in many gold products.