Analogue of electromagnetically induced transparency in square slotted silicon metasurfaces supporting bound states in the continuum.

In this work, a silicon metasurface designed to support electromagnetically induced transparency (EIT) based on quasi-bound states in the continuum (qBIC) is proposed and theoretically demonstrated in the near-infrared spectrum. The metasurface consists of a periodic array of square slot rings etched in a silicon layer. The interruption of the slot rings by a silicon bridge breaks the symmetry of the structure producing qBIC stemming from symmetry-protected states, as rigorously demonstrated by a group theory analysis. One of the qBIC is found to behave as a resonance-trapped mode in the perturbed metasurface, which obtains very high quality factor values at certain dimensions of the silicon bridge. Thanks to the interaction of the sharp qBIC resonances with a broadband bright background mode, sharp high-transmittance peaks are observed within a low-transmittance spectral window, thus producing a photonic analogue of EIT. Moreover, the resonator possesses a simple bulk geometry with channels that facilitate the use in biosensing. The sensitivity of the resonant qBIC on the refractive index of the surrounding material is calculated in the context of refractometric sensing. The sharp EIT-effect of the proposed metasurface, along with the associated strong energy confinement may find direct use in emerging applications based on strong light-matter interactions, such as non-linear devices, lasing, biological sensors, optical trapping, and optical communications.

Microdrilled tapers to enhance optical fiber lasers for sensing.

In this work, an experimental analysis of the performance of different types of quasi-randomly distributed reflectors inscribed into a single-mode fiber as a sensing mirror is presented. These artificially-controlled backscattering fiber reflectors are used in short linear cavity fiber lasers. In particular, laser emission and sensor application features are analyzed when employing optical tapered fibers, micro-drilled optical fibers and 50 µm-waist or 100 µm-waist micro-drilled tapered fibers (MDTF). Single-wavelength laser with an output power level of about 8.2 dBm and an optical signal-to-noise ratio of 45 dB were measured when employing a 50 µm-waist micro-drilled tapered optical fiber. The achieved temperature sensitivities were similar to those of FBGs; however, the strain sensitivity improved more than one order of magnitude in comparison with FBG sensors, attaining slope sensitivities as good as 18.1 pm/µÎµ when using a 50 µm-waist MDTF as distributed reflector.

Strongly resonant silicon slot metasurfaces with symmetry-protected bound states in the continuum.

In this work, a novel all-dielectric metasurface made of arrayed circular slots etched in a silicon layer is proposed and theoretically investigated. The structure is designed to support both Mie-type multipolar resonances and symmetry-protected bound states in the continuum (BIC). Specifically, the metasurface consists of interrupted circular slots, following the paradigm of complementary split-ring resonators. This configuration allows both silicon-on-glass and free-standing metasurfaces and the arc length of the split-rings provides an extra tuning parameter. The nature of both BIC and non-BIC resonances supported by the metasurface is investigated by employing the Cartesian multipole decomposition technique. Thanks to the non-radiating nature of the quasi-BIC resonance, extremely high Q-factor responses are calculated, both by fitting the simulated transmittance spectra to an extended Fano model and by an eigenfrequency analysis. Furthermore, the effect of optical losses in silicon on quenching the achievable Q-factor values is discussed. The metasurface features a simple bulk geometry and sub-wavelength dimensions. This novel device, its high Q-factors, and strong energy confinement open new avenues of research on light-matter interactions in view of new applications in non-linear devices, biological sensors, and optical communications.

Hybrid Raman-erbium random fiber laser with a half open cavity assisted by artificially controlled backscattering fiber reflectors.

A hybrid Raman-erbium random fiber laser with a half-open cavity assisted by chirped artificially controlled backscattering fiber reflectors is presented. A combination of a 2.4 km-long dispersion compensating fiber with two highly erbium-doped fiber pieces of 5 m length were used as gain media. A single random laser emission line centered at 1553.8 nm with an optical signal to noise ratio of 47 dB were obtained when pumped at 37.5 dBm. A full width at half maximum of 1 nm and a 100% confidence level output power instability as low as 0.08 dB were measured. The utilization of the new laser cavity as a temperature and strain sensor is also experimentally studied.

Multifunctional light beam control device by stimuli-responsive liquid crystal micro-grating structures.

There is an increasing need to control light phase with tailored precision via simple means in both fundamental science and industry. One of the best candidates to achieve this goal are electro-optical materials. In this work, a novel technique to modulate the spatial phase profile of a propagating light beam by means of liquid crystals (LC), electro-optically addressed by indium-tin oxide (ITO) grating microstructures, is proposed and experimentally demonstrated. A planar LC cell is assembled between two perpendicularly placed ITO gratings based on microstructured electrodes. By properly selecting only four voltage sources, we modulate the LC-induced phase profile such that non-diffractive Bessel beams, laser stretching, beam steering, and 2D tunable diffraction gratings are generated. In such a way, the proposed LC-tunable component performs as an all-in-one device with unprecedented characteristics and multiple functionalities. The operation voltages are very low and the aperture is large. Moreover, the device operates with a very simple voltage control scheme and it is lightweight and compact. Apart from the demonstrated functionalities, the proposed technique could open further venues of research in optical phase spatial modulation formats based on electro-optical materials.

Positive-negative tunable liquid crystal lenses based on a microstructured transmission line.

In this work, a novel technique to create positive-negative tunable liquid crystal lenses is proposed and experimentally demonstrated. This structure is based on two main elements, a transmission line acting as a voltage divider and concentric electrodes that distribute the voltage homogeneously across the active area. This proposal avoids all disadvantages of previous techniques, involving much simpler fabrication process (a single lithographic step) and voltage control (one or two sources). In addition, low voltage signals are required. Lenses with switchable positive and negative focal lengths and a simple, low voltage control are demonstrated. Moreover, by using this technique other optical devices could be engineered, e.g. axicons, Powell lenses, cylindrical lenses, Fresnel lenses, beam steerers, optical vortex generators, etc. For this reason, the proposed technique could open new venues of research in optical phase modulation based on liquid crystal materials.

Ultrahigh temperature and strain hybrid integrated sensor system based on Raman and femtosecond FBG inscription in a multimode gold-coated fiber.

In this paper, a novel approach for hybrid systems combining Raman distributed sensors with fiber Bragg grating (FBG) sensors to carry out distributed and quasi-distributed temperature/strain measurements was proposed and experimentally demonstrated. Three FBGs were inscribed by the point-by-point technique in a simple setup for type I femtosecond inscription in a pure silica core multimode gold-coated fiber. Employing a single fiber, temperatures up to 600 °C and strains up to 4144 µÉ› approximately were measured simultaneously and without interferences between both distributed and point measurements. Moreover, a new calibration technique was implemented to calibrate the distributed temperature system using the FBG measurements as reference.

Recovering a fiber Bragg grating axial strain distribution from its reflection spectrum.

A processing scheme able to obtain any arbitrary intragrating strain distribution of a fiber Bragg grating (FBG) is proposed and demonstrated. The processing method employs just the intensity of the FBG reflection spectrum to obtain its deformation profile by combining a geometrical processing scheme with the particle swarm optimization technique. The technique has been evaluated using several spectra generated from very heterogeneous strain distributions and with a real spectrum obtained from a 5 mm length FBG under an asymmetric perturbation. The achieved results exhibit a good spatial resolution (Δ≈0.5 mm) and repeatability.

Single-longitudinal mode laser structure based on a very narrow filtering technique.

A narrow filtering technique based on the spectral overlapping of two uniform FBGs and applied to obtain a Single Longitudinal Mode (SLM) laser is proposed and demonstrated in this work. The two FBGs are spectrally detuned to reduce their coincident reflection response narrowing the equivalent filter bandwidth. A proof-of-concept linear laser has been built and tested exhibiting SLM operation even with temperature and strain variations.

Sampled Fiber Bragg Grating spectral synthesis.

In this paper, a technique to estimate the deformation profile of a Sampled Fiber Bragg Grating (SFBG) is proposed and experimentally verified. From the SFBG intensity reflection spectrum, any arbitrary longitudinal axis deformation profile applied to a SFBG is estimated. The synthesis algorithm combines a custom defined error metric to compare the measured and the synthetic spectra and the Particle Swarm Optimization technique to get the deformation profile. Using controlled deformation profiles, the proposed method has been successfully checked by means of simulated and experimental tests. The results obtained under different controlled cases show a remarkable repetitiveness (< 50 µÎµ) and good spatial accuracy (< 1 mm).

Prospective, randomised, multicentre study of meropenem versus imipenem/cilastatin as empiric monotherapy in severe nosocomial infections.

The clinical and bacteriological efficacy and the tolerability of meropenem versus imipenem/cilastatin (both 1 g t.i.d.) in severe nosocomial infections were compared in a multicentre, randomised, nonblinded study. A total of 151 patients were recruited; 133 (66 meropenem, 67 imipenem/cilastatin) were clinically evaluable and 84 (42 meropenem, 42 imipenem/cilastatin) bacteriologically evaluable. Most clinically evaluable patients (90%) were in intensive care units, required mechanical ventilation (72%), and had received previous antibiotic therapy (62%). The mean (+/- SD) APACHE II score was 15.2 (+/- 6.6) in the meropenem group and 17.8 (+/- 6.8) in the imipenem/cilastatin group. The primary infections were nosocomial lower respiratory tract infections (56% of patients), intra-abdominal infections (15%), septicaemia (21%), skin/skin structure infections (5%), and complicated urinary tract infections (3%); 35% of the patients had two or more infections. There was no significant difference between the meropenem and imipenem/cilastatin groups in the rates of satisfactory clinical (weighted percentage 87% vs. 74%) or bacteriological (weighted percentage 79% vs. 71%) response. There was a slightly higher rate of clinical success with meropenem against primary or secondary lower respiratory tract infection (89% vs. 76%). Drug-related adverse events occurred in 17% and 15% of meropenem and imipenem/cilastatin patients, respectively. Meropenem (1 g t.i.d.) was as efficacious as the same dose of imipenem/cilastatin in this setting, and both drugs were well tolerated.

Lens capsule opacification in aphakic and pseudophakic eyes.

BACKGROUND: Posterior capsule opacification (PCO) is the most common complication of lens extraction. Although intraocular lenses (IOLs) are thought to inhibit capsule opacification, the mechanisms by which they do this are poorly understood. This study was done to determine the effects of pseudophakia on secondary cataract and PCO in experimentally lentectomized dogs. METHODS: Twenty-four normal dogs were bilaterally lentectomized by phacoemulsification and unilaterally implanted with a plano-convex polymethylmethacrylate IOL. Secondary cataracts and capsule opacification were evaluated at weeks 1, 2, 4, 10, 14, and 20 after surgery by retrolillumination photography, light microscopy, and scanning and transmission electron microscopy. RESULTS: The pattern of secondary cataract and PCO in dogs was found to be similar to that in other animal species. Production of new lens material was prominent in the equatorial region, and PCO resulted from fibrous metaplasia of lens epithelium and subsequent capsular fibrosis and wrinkling. The presence of an IOL did not prevent the posterior migration of epithelium, nor did it prevent fibrous metaplasia. The presence of an IOL did, however, minimize the capsule-wrinkling effects of fibroplasia and limit the space available for lentoid formation. CONCLUSION: In pseudophakic eyes, IOLs influence secondary cataract formation by limiting the space available for lentoid formation and by maintaining a linear scaffolding for lens epithelial fibrous metaplasia.

Inhibition of proliferating lens epithelium with antitransferrin receptor immunotoxin.

We investigated the effect of an antitransferrin receptor immunotoxin (454A12-rRA) on proliferating human and baboon lens epithelium in vitro. Human and baboon lens epithelial cells grown in modified TC-199 medium at 35 degrees Celsius in 7% CO2 were seeded in 24 well plates at a density of 17,500 cells/ml to 40,000 cells/ml. The cells were exposed to various concentrations of 454A12-rRA for seven days. The sensitivity of proliferating human lens epithelium to 454A12-rRA was dependent on the dose, with a 60% to 70% reduction in cell counts at immunotoxin concentrations of 100 ng/ml and above. The immunotoxin had no significant effect on baboon lens epithelium in vitro, which suggests that it is specific for human tissue. By preventing the proliferation of human lens epithelial cells, immunotoxin 454A12-rRA may be useful in the management of posterior capsule opacification after planned extracapsular cataract surgery.

Suppression of human corneal epithelial proliferation with breast carcinoma immunotoxin.

We examined the effects of the immunotoxin 260F9 Mab-recombinant ricin A (developed against human breast carcinoma) on proliferating and confluent human corneal epithelium (HCE) cells in vitro. HCE cells derived from explants of discarded human donor corneoscleral rims were established as proliferating and confluent cell cultures, and were exposed continuously for 7 days to immunotoxin. Final cell counts at day 7, and thymidine uptake measured at days 1 and 7 postexposure, showed > 95% suppression of proliferating cells at an immunotoxin concentration of 10 ng/ml, with confluent HCE cells relatively unaffected. This immunotoxin may prove useful in treatment of proliferative ocular epithelial diseases such as epithelial downgrowth or squamous cell carcinoma of the ocular surface.

Ultrastructure of fiber cells and multilamellar inclusions in experimental diabetes.

PURPOSE: The goal of this ultrastructural study was to examine fiber cell shape and intercellular junctions during the early stages of fiber cell breakdown and edema in diabetic rabbit lenses. METHODS: Lens abnormalities were recorded with a slit lamp. Between 6-10 mo after drug treatment, diabetic lenses and untreated control lenses were freshly enucleated and sectioned with a vibrating knife microtome. The thick tissue sections were chemically fixed and processed for thin-section electron microscopy. RESULTS: Alloxan-induced diabetes in albino rabbits produced clinically apparent cataracts as soon as 1 mo after the animals became hyperglycemic. The cataracts displayed cortical fluid-filled vacuoles in the equatorial region and at the cortex-nucleus interface, white specks scattered throughout the cortex, and posterior subcapsular cataracts. Fiber cells just deeper than the large cortical vacuoles had oval or spindle-shaped cross sections. Multilamellar inclusions, not reported previously for diabetic lenses, were observed at or near the fiber cell interfaces and were composed of concentric or spiral rings of plasma membrane-bound cytoplasmic processes. Undulating membranes were present throughout most of the multilamellar inclusions. Transparent lenses from untreated controls did not have such multilamellar bodies or extensive membrane undulations in cells at the same distance from the lens surface. CONCLUSIONS: Fiber cells respond to the diabetic insult differently depending on their stage of differentiation and age. The observed changes are consistent with the hypothesis that hyperglycemia accelerates the formation of age-related changes in fiber cells.

Analysis of corneal and conjunctival microenvironments using monoclonal antibodies.

PURPOSE: The authors phenotypically compared epithelial and nonepithelial components of human corneal and conjunctival microenvironments using a panel of monoclonal antibody reagents that included markers of epithelial cell maturation, markers of mesodermal-derived fibrous tissue and vessels, markers of specific keratins, and markers of major histocompatibility complex Class I and II antigens. METHODS: Corneoscleral rims obtained after trephination of the donor button for use in penetrating keratoplasty procedures were studied. RESULTS: A comparison of cornea and conjunctiva with anti-epithelial and antikeratin antibodies demonstrated that corneal and conjunctival keratinocytes undergo similar antigenically defined pathways of maturation. However, the reactivity of antibody 12/1-2 (antibody against low molecular weight keratins) with conjunctival but not corneal basal cells suggested differences in keratin expression between the two epithelial types. Using antibodies against major histocompatibility complex Class I and II antigens, it was demonstrated the two tissues were similar with Class I determinants found on all epithelial, stromal, and endothelial cells, and Class II determinants found on Langerhans' cells, vessels, and a subset of stromal cells. CONCLUSIONS: The availability of tissue-specific markers of epithelial and nonepithelial components of the cornea and conjunctiva should be of use in the study of the roles the ocular microenvironment might play in the pathogenesis of ocular inflammatory diseases.

Acyclovir-resistant herpes simplex virus keratouveitis after penetrating keratoplasty.

PURPOSE: A case of acyclovir-resistant herpes simplex virus keratouveitis after penetrating keratoplasty is reported. METHODS: Resistance to acyclovir was evident clinically and was confirmed by in vitro susceptibility testing. The susceptibility of the herpes simplex isolates to acyclovir and foscarnet was determined by a dye uptake assay that measured cytopathic effect, and thymidine kinase activity was measured by a plaque autoradiography technique. RESULTS: The viral isolate from postoperative day 22 was susceptible to acyclovir and foscarnet, and showed normal thymidine kinase activity. Isolates from postoperative days 29 and 32 (coinciding with deterioration in clinical appearance) were resistant to acyclovir, susceptible to foscarnet, and deficient in thymidine kinase activity. CONCLUSION: Practitioners should be aware of the potential for the emergence of resistance in this setting; prophylaxis and rational alternate therapies are discussed.