Anticounterfeiting and Fraud Mitigation Solutions for High-value Food Products.

Globalization and the increasing complexity of supply chains have allowed food fraud to expand to a great extent. Some of the most serious effects of these deceitful activities are damage to a brand's reputation and trust, economic losses, and public health risks. The usual victims of food fraud are dairy, meat, fish, and seafood products, as well as fats/oils and alcoholic drinks. The purpose of this review paper is to present an updated analysis of the currently available anticounterfeit technologies and their application to the four most fraud-affected food supply chains. An assessment that was conducted to determine when the adoption of a combination of technologies could enhance food safety and brand protection is also provided. The obtained results indicate that electronic and data-driven technologies (RFID devices and digital traceability systems) are still in their infancy in the food sectors that are subjected the most to fraudulent activities. Research is necessary to develop innovative digital and physical technologies to "outsmart" such fraudsters and to prevent their illicit actions in the food sector.

UAV-spray application in vineyards: Flight modes and spray system adjustment effects on canopy deposit, coverage, and off-target losses.

Improvements in the spray application of plant protection products enhance agricultural sustainability by reducing environmental contamination, but by increasing food quality and human safety. Currently, Unmanned Aerial Vehicles (UAVs) are raising interest in spray applications in 3D crops. However, operational configurations of UAV-spray systems need further investigation to maximise the deposition in the canopy and minimise the off-target losses. Our experimental research focused on investigating the effects on the canopy spray deposition and coverage due to different UAV-spray system configurations. Twelve configurations were tested under field conditions in an experimental vineyard (cv. Barbera), derived from the combination of different UAV flight modes (band and broadcast spray applications), nozzle types (conventional and air inclusion), and UAV cruise speeds (1 and 3 m s-1). Also, the best treatment, among those tested, by using the UAV-spray system and a traditional airblast sprayer were compared. The data was analysed by testing the effects of the three operational parameters and their two- and three-way interactions by means of linear mixed models. The results indicated that the flight mode deeply affects spray application efficiency. Compared to the broadcast spray modes, the band spray mode was able to increase the average canopy deposition from 0.052 to 0.161 µL cm-2 (+ 309 %) and reduce the average ground losses from 0.544 to 0.246 µL cm-2 (- 54 %). The conventional airblast sprayer, operated at a low spray application rate, showed higher canopy coverage and lower ground losses in comparison to the best UAV-spray system configuration.

Effect of postoperative peroxide bleaching on the marginal seal of composite restorations bonded with self-etch adhesives.

The aim of this study was to determine the effect of peroxide bleaching on the marginal seal of composite restorations bonded with several adhesive systems. Combined cylindrical Class V cavities located half in enamel and half in dentin were prepared on the buccal and lingual surfaces of human molars. The cavities were bonded with the self-etch adhesives Clearfil SE-Bond (CLF), Adper Prompt (ADP), and iBond (IBO) and an etch-and-rinse adhesive Gluma Comfort Bond (GLU) and restored with a microhybrid composite Charisma. Experimental groups were treated 25 times for eight hours per day with a peroxide bleaching gel Opalescence PF 20, while the control groups were stored in distilled water for two months and then subjected to a microleakage test using a dye penetration method. Scanning electron microscopy was used to investigate the etching and penetration abilities of the adhesives and morphology of debonded restoration-enamel interfaces after the microleakage tests. Statistical analyses were performed using nonparametric Kruskal-Wallis, Mann-Whitney, and Wilcoxon tests at p=0.05. The microleakage of all GLU groups was low and not significantly affected by peroxide bleaching. Low microleakage was recorded for CLF control groups, but after bleaching, a small but significant increase in microleakage at the enamel margin indicated its sensitivity to peroxide bleaching. For ADP and IBO control groups, the microleakage at the enamel margins was significantly higher than for GLU and CLF and exceeded that at the dentin margins. Bleaching did not induce any significant changes in the microleakage. Electron microscopy analysis indicated that in our experimental setup, decreased adhesion and mechanical resistance of the ADP- and IBO-enamel interfaces could be more important than the chemical degradation effects induced by the peroxide bleaching gel.

Effect of postoperative peroxide bleaching on the stability of composite to enamel and dentin bonds.

This study investigated the effect of peroxide bleaching gel on the durability of the adhesive bond between composite material, enamel, and dentin created with the etch-and-rinse adhesive Gluma Comfort Bond (GLU) and with the self-etch adhesives Clearfil SE Bond (CLE), Adper Prompt (ADP), and iBond (IBO). The adhesives were applied to flattened enamel and dentin of extracted human molars and built up with a microhybrid composite (Charisma). After 25 eight-hour cycles of bleaching with a 20% carbamide peroxide bleaching gel (Opalescence PF 20), the shear bond strength was measured and compared with one-day and two-month control specimens stored in water. The data were analyzed using nonparametric Mann-Whitney and Kruskal-Wallis statistics (p<0.05). Detailed fractographic analysis was performed using scanning electron microscopy. The bleaching gel significantly decreased the bond strength on both enamel and dentin for the simplified single-step self-etch adhesives ADP and IBO and markedly affected a fracture pattern of ADP specimens at the periphery of their bonded area. The results of our study indicate that the durability of adhesive restorations can be detrimentally influenced by carbamide peroxide bleaching and that different adhesives show varying sensitivity levels to the bleaching gel.