Determination of furfurals in Manuka honey using piston-cylinder liquid-liquid extraction and gas chromatography.

A rapid analytical approach for the direct measurement of furfurals such as 2-furfural and 5-methyl-2-furfural at parts-per-billion level in Manuka honey is described. The approach employs a piston-cylinder based liquid-liquid extraction device using chloroform extraction solvent. This device substantially reduces extraction time by a factor of 120 times compared to solid phase micro-extraction and reduces solvent consumption by a factor of 25 times compared to liquid-liquid extraction with mechanical agitation. A recently commercialised capillary column offering a high degree of inertness permits separation and detection of the analytes at ultra-trace level without derivatisation. A three-port planar microfluidic device with a mid-point pressure is also incorporated to back-flush heavier compounds in the matrix to improve column longevity and overall system cleanliness. With this approach, analysis is conducted in less than 7min. Repeatability of retention times for all compounds is less than 0.1% (n=20). The compounds cited can be analysed over a range from 1ng/g to 10µg/g in honey with a 5ng/g limit of quantification (LOQ) and correlation coefficients of at least 0.999. Relative precision is less than 2.8% RSD (n=20) at 50ng/g level with analyte extraction efficiency of greater than 99% (n=3) over a range from 5ng/g to 10µg/g in the matrix described. The analytical system requires only minimal maintenance and is suitable for remote site deployment. Under the analytical conditions established and with a practical LOQ of 5ng/g, 100 samples can be analysed before septum/liner/o-ring replacements are needed. As a preventive measure, the pre-column can be replaced once every six months to maintain chromatographic fidelity.

Determination of trace ethylene glycol in industrial solvents and lubricants using phenyl boronic acid derivatization and multidimensional gas chromatography.

A practical gas chromatographic approach is introduced for the characterization of trace ethylene glycol in industrial solvents and lubricants. The analytical approach employs single step derivatization technique that effectively converts ethylene glycol to the cyclic boronate ester (2-phenyl-1,3,2-dioxaborolane), using phenyl boronic acid as a derivatizing reagent. The separation of the derivatized product was achieved by using multidimensional gas chromatography. Heavy lubricant matrices like engine crankcase oil were back-flushed to improve sample throughput and system cleanliness. Detection and quantitation of 2-phenyl-1,3,2-dioxaborolane was conducted with mass spectrometry in selected ion monitoring mode. Complete analysis is conducted in less than 10 min. Reproducibility of retention time was found to be less than 0.05% (n=20). Quantitative performance is highly satisfactory, viz. 0.49±0.02 mg kg(-1) (n=12) and 25.5±0.48 mg kg(-1) (n=12) for 0.5 mg kg(-1) and 25 mg kg(-1) spiked concentrations respectively. Over a range from 100 µg kg(-1) to 100 mg kg(-1), the response for 2-phenyl-1,3,2-dioxaborolane is linear with correlation coefficient of 0.998, a practical detection limit of 50 µg kg(-1), and average spiked recoveries for the analyte in the matrices tested range from 93 to 99%. Propylene glycol can also be analyzed using the same approach and water does not inhibit the formation of the derivatives, most probably owing to the use of 2,2-dimethoxypropane as a solvent for the derivatizing agent.

Characterization of phenol and alkyl phenols in organic matrixes with monoethylene glycol extraction and multidimensional gas chromatography/mass spectrometry.

The use of monoethylene glycol as an extraction medium for removing phenol and alkyl phenols in organic matrixes such as hydrocarbons is introduced and combined with a practical analytical multidimensional gas chromatography approach. The analytical approach has been successfully developed for the characterization of phenol, cresols, xylenols, and alkyl phenols like 4-ethylphenol and 2,3,5-trimethylphenol. The technique employs a single-step extraction of the analytes with monoethylene glycol and sonication, followed by multidimensional gas chromatography with mass spectrometry in selected ion monitoring mode for the detection and quantitation. Extraction efficiency of phenol approached 100% while cresols, xylenols, and 4-ethylphenol were 97% or higher and 2,3,5-trimethylphenol was better than 91% under the analytical conditions used. With the technique described, a complete analysis can be conducted in less than 16 min. Reproducibility of area counts at two levels, namely, 5 ppm(w) and 50 ppm(w) over a period of 2 days were found to be less than 4% (n = 20). The analytes of interest was found to be linear over a range from 100 ppb(w) to 250 ppm(w) with correlation coefficient of at least 0.999 and detection limit of 50 ppb(w) . Spike recoveries from 500 ppb(w) to 250 ppm(w) for all analytes range from 96 to 102%.

Tandem sulfur chemiluminescence and flame ionization detection with planar microfluidic devices for the characterization of sulfur compounds in hydrocarbon matrices.

The detection of sulfur compounds in different hydrocarbon matrices, from light hydrocarbon feedstocks to medium synthetic crude oil feeds provides meaningful information for optimization of refining processes as well as demonstration of compliance with petroleum product specifications. With the incorporation of planar microfluidic devices in a novel chromatographic configuration, sulfur compounds from hydrogen sulfide to alkyl dibenzothiophenes and heavier distributions of sulfur compounds over a wide range of matrices spanning across a boiling point range of more than 650°C can be characterized, using one single analytical configuration in less than 25min. In tandem with a sulfur chemiluminescence detector for sulfur analysis is a flame ionization detector. The flame ionization detector can be used to establish the boiling point range of the sulfur compounds in various hydrocarbon fractions for elemental specific simulated distillation analysis as well as profiling the hydrocarbon matrices for process optimization. Repeatability of less than 3% RSD (n=20) over a range of 0.5-1000 parts per million (v/v) was obtained with a limit of detection of 50 parts per billion and a linear range of 0.5-1000 parts per million with a correlation co-efficient of 0.998.

Multidimensional gas chromatography using microfluidic switching and low thermal mass gas chromatography for the characterization of targeted volatile organic compounds.

Volatile organic compounds such as light hydrocarbons, dienes, and aromatic compounds are often encountered in the manufacturing and processing environments of chemical and petrochemical segments. These compounds need to be closely monitored for process optimization, plant maintenance and industrial hygiene purposes. A high throughput analytical approach has been successfully developed and implemented for the accurate measurement of fourteen commonly encountered analytes. The approach incorporates a recently introduced 5-port planar microfluidic device configured for use as a Deans switch for multidimensional gas chromatography. The use of multidimensional gas chromatography allows the elimination of potential chromatographic contaminants with a substantial enhancement of stationary phase selectivity via the use of columns with different separation mechanisms, and the back-flushing of heavier undesired hydrocarbons. A low thermal mass gas chromatographic module was employed in the second dimension of the two-dimensional gas chromatography system and was used to provide independent temperature control, and rapid heating and cooling to meet the high throughput requirements. By successfully combining these concepts, complete analysis of fourteen targeted components can be conducted in less than 120s. Repeatability of retention times for all compounds was found to be less than 0.05% (n=20). Repeatability of area counts at two levels, namely 10ppmv and 1000ppmv over a period of two days was found to be less than 3% (n=20). Apart from methane, which has a detection limit of 0.4ppmv, the rest of the compounds were found to have detection limits of less than 0.2ppmv. Compounds of interest were found to be linear over a range of 500ppbv-3000ppmv with correlation coefficients greater than 0.999.

Temperature-programmable resistively heated micromachined gas chromatography and differential mobility spectrometry detection for the determination of non-sulfur odorants in natural gas.

A portable, fast gas chromatographic method for the direct measurement of the parts per billion level of sulfur-free odorants in commercially available natural gas is introduced. The approach incorporates a resistively heated, temperature-programmable silicon micromachined gas chromatograph that employs a standard capillary column for the fast separation of methyl and ethyl acrylate from the natural gas matrix. The separation approach is coupled to a micromachined differential mobility detector to enhance analyte detectability, and the overall selectivity obtained against the matrix is described. A complete analysis can be conducted in less than 70 s. Furthermore, these two compounds can be measured accurately in the presence of other common volatile sulfur-based odorants such as alkyl mercaptans and alkyl sulfides. Repeatability of less than 3% RSD (n = 20) over a range from 0.5 to 5 ppm was obtained with a limit of detection for the target compounds at 50 ppb (v/v) and a linear range from 0.5 to 50 ppm with a correlation coefficient of at least 0.997.

Multidimensional gas chromatography for the characterization of permanent gases and light hydrocarbons in catalytic cracking process.

An integrated gas chromatographic system has been successfully developed and implemented for the measurement of oxygen, nitrogen, carbon monoxide, carbon dioxide and light hydrocarbons in one single analysis. These analytes are frequently encountered in critical industrial petrochemical and chemical processes like catalytic cracking of naphtha or diesel fuel to lighter components used in gasoline. The system employs a practical, effective configuration consisting of two three-port planar microfluidic devices in series with each other, having built-in fluidic gates, and a mid-point pressure source. The use of planar microfluidic devices offers intangible advantages like in-oven switching with no mechanical moving parts, an inert sample flow path, and a leak-free operation even with multiple thermal cycles. In this way, necessary features such as selectivity enhancement, column isolation, column back-flushing, and improved system cleanliness were realized. Porous layer open tubular capillary columns were employed for the separation of hydrocarbons followed by flame ionization detection. After separation has occurred, carbon monoxide and carbon dioxide were converted to methane with the use of a nickel-based methanizer for detection with flame ionization. Flow modulated thermal conductivity detection was employed to measure oxygen and nitrogen. Separation of all the target analytes was achieved in one single analysis of less than 12 min. Reproducibility of retention times for all compounds were found to be less than 0.1% (n=20). Reproducibility of area counts at two levels, namely 100 ppm(v) and 1000 ppm(v) over a period of two days were found to be less than 5.5% (n=20). Oxygen and nitrogen were found to be linear over a range from 20 ppm(v) to 10,000 ppm(v) with correlation coefficients of at least 0.998 and detection limits of less than 10 ppm(v). Hydrocarbons of interest were found to be linear over a range from 200 ppb(v) to 1000 ppm(v) with correlation coefficients of greater than 0.999 and detection limits of less than 100 ppb(v).

Temperature-programmable low thermal mass silicon micromachined gas chromatography and differential mobility detection for the fast analysis of trace level of ethylene oxide in medical work place atmospheres.

A portable, fast gas chromatographic method for the direct measurement of part-per-billion level of ethylene oxide in medical work place atmospheres is introduced. Ethylene oxide is a chemical of significance in life science for its critical role as a highly effective sterilizing agent for heat sensitive surgical instruments. However, ethylene oxide is highly flammable, a suspected human carcinogen, is mutagenic, and henceforth, requires close monitoring. The approach incorporates a temperature-programmable silicon micromachined gas chromatograph for the fast separation of ethylene oxide from airborne organic interferences. The separation approach is hyphenated to a micromachined differential mobility detector, improving targeted analyte detection, and enhancing the overall selectivity obtained. A complete analysis can be conducted in less than 60s. Further, ethylene oxide in the matrix mentioned can be measured directly with low possibility of false positives and without the need for any sample pre-treatment, such as pre-concentration or derivatization. A relative precision of less than 5% RSD (n=20) over a range from 5 parts per billion (v/v) to 500 parts per billion (v/v) was obtained.

On-line coupling of supercritical fluid extraction with multidimensional microcolumn liquid chromatography/gas chromatography.

An on-line multidimensional supercritical fluid extraction/microcolumn liquid chromatography/capillary gas chromatography system (SFE/LC/GC) has been developed and applied to the quantitative determination of trace levels (parts per billion) of chlorpyrifos insecticide in grass field samples. This system provides all the advantages of an on-line multidimensional system, including increased resolving power, high sensitivity, quantitation, precision, and automation potential. Off-line analysis of the grass extracts by GC with an electron capture detector yielded a complex chromatogram from which it was difficult to quantitate the chlorpyrifos, but analysis of the extract by LC/GC yielded a simple chromatogram from which chlorpyrifos could be quantitated. On-line SFE/LC/GC resulted in reduced sample preparation with the grass extract being deposited directly on the LC microcolumn via an impactor interface, followed by the LC/GC separation. The reproducibility of the on-line SFE/LC/GC procedure was studied and found to yield a relative standard deviation of 10.8% for the determination of chlorpyrifos insecticide in grass field samples at a concentration of 160 ng/g. Using this method, the entire analysis including extraction, clean-up, and gas chromatography required less than 0.1 mL of organic solvent.

Some industrial developments and applications of multidimensional techniques.

Industrial analytical chemistry includes the measurement of the elemental composition and structure of molecules; the measurement of the concentration of specific molecules, atoms, and ions in contact with other molecules, atoms, and ions, the measurement of the energy and speed with which these reactions occur; and the separation of molecules, atoms, and ions specifically from other molecules, atoms and ions. It is also the measurement of the physical (interaction) and chemical (reaction) behavior of collections of molecules and how this behavior is controlled by the presence of other molecules and ions. Many excellent devices for separation and measurement have been developed to accomplish these tasks. Each of these attains a level of sensitivity and selectivity beyond which further improvement would be difficult. However, by coupling these techniques in various configurations, improved data can be generated in a short time span. Such techniques are often referred to as hyphenated, tandem, combined, or coupled. A more inclusive term is multidimensional techniques. In this paper, we briefly describe some of the most significant developments our laboratory has made in these and related techniques.