Polarization Control in Integrated Silicon Waveguides Using Semiconductor Nanowires.

In this work, we show the design of a silicon photonic-based polarization converting device based on the integration of semiconduction InP nanowires on the silicon photonic platform. We present a comprehensive numerical analysis showing that full polarization conversion (from quasi-TE modes to quasi-TM modes, and vice versa) can be achieved in devices exhibiting small footprints (total device lengths below 20 µm) with minimal power loss (<2 dB). The approach described in this work can pave the way to the realization of complex and re-configurable photonic processors based on the manipulation of the state of polarization of guided light beams.

Yield stress "in a flash": investigation of nonlinearity and yielding in soft materials with an optofluidic microrheometer.

Yield stress materials deform as elastic solids or flow as viscous liquids, depending on the applied stress, which also allows them to trap particles below a certain size or density threshold. To investigate the conditions for such a transition at the microscale, we use an optofluidic microrheometer, based on the scattering of an infrared beam onto a microbead, which reaches forces in the nN scale. We perform creep experiments on a model soft material composed of swollen microgels, determining the limits of linear response and yield stress values, and observe quantitative agreement with bulk measurements. However, the motion of the microbead, both below and above yielding, reflects distinctive microscale features of the surrounding material, whose plastic rearrangements were investigated by us using small, passive tracers.

Integrated Optofluidic Chip for Oscillatory Microrheology.

We propose and demonstrate an on-chip optofluidic device allowing active oscillatory microrheological measurements with sub-µL sample volume, low cost and high flexibility. Thanks to the use of this optofluidic microrheometer it is possible to measure the viscoelastic properties of complex fluids in the frequency range 0.01-10 Hz at different temperatures. The system is based on the optical forces exerted on a microbead by two counterpropagating infrared laser beams. The core elements of the optical part, integrated waveguides and an optical modulator, are fabricated by fs-laser writing on a glass substrate. The system performance is validated by measuring viscoelastic solutions of aqueous worm-like micelles composed by Cetylpyridinium Chloride (CPyCl) and Sodium Salicylate (NaSal).

Newtonian to non-newtonian fluid transition of a model transient network.

The viscosity of gel-forming fluids is notoriously complex and its study can benefit from new model systems that enable a detailed control of the network features. Here we use a novel and simple microfluidic-based active microrheology approach to study the transition from Newtonian to non-Newtonian behavior in a DNA hydrogel whose structure, connectivity, density of bonds, bond energy and kinetics are strongly temperature dependent and well known. In a temperature range of 15 °C, the system reversibly and continuously transforms from a Newtonian dispersion of low-valence nanocolloids into a strongly shear-thinning fluid, passing through a set of intermediate states where it behaves as a power-law fluid. We demonstrate that the knowledge of network topology and bond free energy enables to quantitatively predict the observed behavior using established rheology models.

High-efficiency grating-couplers: demonstration of a new design strategy.

We present a simple and practical strategy that allows to design high-efficiency grating couplers. The technique is based on the simultaneous apodization of two structural parameters: the grating period and the fill-factor, along with the optimization of the grating coupler etching depth. Considering a 260 nm Si-thick Silicon-on-insulator platform, we numerically demonstrated a coupling efficiency of -0.8 dB (83%), well matching the experimental value of -0.9 dB (81%). Thanks to the optimized design, these results represent the best performance ever reported in the literature for SOI structures without the use of any back-reflector.

Group-velocity dispersion in SOI-based channel waveguides with reduced-height.

We report on the experimental characterization, in the telecom C-band, of group-velocity dispersion (D) in 100-nm high rectangular strip waveguides realized by silicon-on-insulator technology. We compare the experimental results with numerical predictions, showing that 100-nm high waveguides exhibit normal dispersion and that the absolute value of the dispersion coefficient D decreases as the waveguide width is increased. D at 1550 nm varies from -8130 to -3900 ps/(nm·km) by increasing the waveguide width from 500 to 800 nm.

A comprehensive strategy for the analysis of acoustic compressibility and optical deformability on single cells.

We realized an integrated microfluidic chip that allows measuring both optical deformability and acoustic compressibility on single cells, by optical stretching and acoustophoresis experiments respectively. Additionally, we propose a measurement protocol that allows evaluating the experimental apparatus parameters before performing the cell-characterization experiments, including a non-destructive method to characterize the optical force distribution inside the microchannel. The chip was used to study important cell-mechanics parameters in two human breast cancer cell lines, MCF7 and MDA-MB231. Results indicate that MDA-MB231 has both higher acoustic compressibility and higher optical deformability than MCF7, but statistical analysis shows that optical deformability and acoustic compressibility are not correlated parameters. This result suggests the possibility to use them to analyze the response of different cellular structures. We also demonstrate that it is possible to perform both measurements on a single cell, and that the order of the two experiments does not affect the retrieved values.

Investigation of temperature effect on cell mechanics by optofluidic microchips.

Here we present the results of a study concerning the effect of temperature on cell mechanical properties. Two different optofluidic microchips with external temperature control are used to investigate the temperature-induced changes of highly metastatic human melanoma cells (A375MC2) in the range of ~0 - 35 °C. By means of an integrated optical stretcher, we observe that cells' optical deformability is strongly enhanced by increasing cell and buffer-fluid temperature. This finding is supported by the results obtained from a second device, which probes the cells' ability to be squeezed through a constriction. Measured data demonstrate a marked dependence of cell mechanical properties on temperature, thus highlighting the importance of including a proper temperature-control system in the experimental apparatus.

Optimising apodized grating couplers in a pure SOI platform to -0.5 dB coupling efficiency.

We present a theoretical optimisation of 1D apodized grating couplers in a "pure" Silicon-On-Insulator (SOI) architecture, i.e. without any bottom reflector element, by means of a general mutative method. We perform a comprehensive 2D Finite Difference Time Domain study of chirped and apodized grating couplers in 220 nm SOI, and demonstrate that the global maximum coupling efficiency in that platform is capped to 65% (-1.9 dB). Moving to designs with thicker Si-layers, we identify a new record design in 340 nm SOI, with a simulated coupling efficiency of 89% (-0.5 dB). Going to thicker Si layers does not further improve the efficiency, implying that -0.5 dB may be a global maximum for a grating coupler in SOI without a bottom-reflector. Even after allowing for 193 nm UV-lithographic fabrication constraints, the 340 nm design still offers -0.7 dB efficiency. These new apodized designs are the first pure SOI couplers compatible with deep-UV lithography to offer better than -1 dB insertion losses. With only very minor changes to existing deposition and lithography recipes, they are compatible with the multi-project wafer runs already offered by Si-Photonics foundries.

Tunable Q-factor silicon microring resonators for ultra-low power parametric processes.

A compact silicon ring resonator is demonstrated that allows simple electrical tuning of the ring coupling coefficient and Q-factor and therefore the resonant enhancement of on-chip nonlinear optical processes. Fabrication-induced variation in designed coupling fraction, crucial in the resonator performance, can be overcome using this post-fabrication trimming technique. Tuning of the microring resonator across the critical coupling point is demonstrated, exhibiting a Q-factor tunable between 9000 and 96,000. Consequently, resonantly enhanced four-wave mixing shows tunable efficiency between -40 and -16.3 dB at an ultra-low on-chip pump power of 0.7 mW.

Optimizing polarization-diversity couplers for Si-photonics: reaching the -1dB coupling efficiency threshold.

Polarization-diversity couplers are low-cost industrially-scalable passive devices that can couple light of unknown polarization from a telecom fiber-mode to a pair of TE-polarized wave-guided modes in the Silicon-on-Insulator platform. These couplers offer significantly more relaxed alignment tolerances than edge-coupling schemes, which is advantageous for commercial fiber-packaging of Si-photonic circuits. However, until now, polarization-diversity couplers have not offered sufficient coupling efficiency to motivate serious commercial consideration. Using 3D finite difference time domain calculations for device optimization, we identify Silicon-on-Insulator polarization-diversity couplers with 1,550 nm coupling efficiencies of -0.95 dB and -1.9 dB, for designs with and without bottom-reflector elements, respectively. These designs offer a significant improvement over state-of-the-art performance, and effectively bridge the "performance gap" between polarization-diversity couplers and 1D-grating couplers. Our best polarization-diversity coupler design goes beyond the -1dB efficiency limit that is typically accepted as the minimum needed for industrial adoption of coupler devices in the telecoms market.

Broad parameter optimization of polarization-diversity 2D grating couplers for silicon photonics.

Polarization-diversity couplers, which are designed to couple the unknown polarization state of an optical fiber into the TE-polarized modes of integrated waveguides, are important for the development of practical all-optical circuits. We describe the use of a full 3D finite difference time domain (FDTD) calculation campaign to rigorously optimize the 2D photonic crystal grating that couples a single-mode telecom fiber to the silicon waveguides of a Silicon-on-Insulator (SOI) platform. With this approach we identify the unique optimum combination of etch-depth, hole-radius, and grating-pitch of the photonic crystal array for best performance at 1550 nm. The mean (polarization-averaged) coupling efficiency of 48% (-3.2dB) exceeds reported efficiencies of analogous couplers, and has only a marginal dependence on the polarization state of the input fiber (48 ± 3%). In addition, 3D-FDTD calculations are used to characterize the propagation direction, mode-profile, and polarization of light coupled from the fiber into the SOI slab. Such information is crucial for component design and goes beyond previously available results from existing approximations and simulations of 2D-grating coupler performance. Calculations of photonic mode dispersion in the grating coupler, by means of guided-mode expansion, indicate that the coupling is due to an optically active resonant guided mode in the photonic crystal array. This points towards a fast optimization scheme that enhances both the performance and the physical interpretation of 3D-FDTD simulations.

Validation and perspectives of a femtosecond laser fabricated monolithic optical stretcher.

The combination of high power laser beams with microfluidic delivery of cells is at the heart of high-throughput, single-cell analysis and disease diagnosis with an optical stretcher. So far, the challenges arising from this combination have been addressed by externally aligning optical fibres with microfluidic glass capillaries, which has a limited potential for integration into lab-on-a-chip environments. Here we demonstrate the successful production and use of a monolithic glass chip for optical stretching of white blood cells, featuring microfluidic channels and optical waveguides directly written into bulk glass by femtosecond laser pulses. The performance of this novel chip is compared to the standard capillary configuration. The robustness, durability and potential for intricate flow patterns provided by this monolithic optical stretcher chip suggest its use for future diagnostic and biotechnological applications.

Soft proton exchanged channel waveguides in congruent lithium tantalate for frequency doubling.

We report on stable optical waveguides fabricated by soft-proton exchange in periodically-poled congruent lithium tantalate in the α-phase. The channel waveguides are characterized in the telecom wavelength range in terms of both linear properties and frequency doubling. The measurements yield a nonlinear coefficient of about 9.5 pm/V, demonstrating that the nonlinear optical properties of lithium tantalate are left nearly unaltered by the process.

Optical phase conjugation in phase-modulated transmission systems: experimental comparison of different nonlinearity-compensation methods.

We experimentally compare the effectiveness of three different optical-phase-conjugation-based nonlinearity-compensation strategies on a transmission system employing phase-modulated signals, and hence affected by the Gordon-Mollenauer effect. We demonstrate that it is possible to obtain significant nonlinearity compensation, but that no improvement is obtained using configurations specifically aimed at the compensation of the nonlinear phase noise.

Optofluidic chip for single cell trapping and stretching fabricated by a femtosecond laser.

The authors present the design and optimization of an optofluidic monolithic chip, able to provide optical trapping and controlled stretching of single cells. The chip is fabricated in a fused silica glass substrate by femtosecond laser micromachining which can produce both optical waveguides and microfluidic channels with great accuracy. A new fabrication procedure adopted in this work allows the demonstration of microchannels with a square cross-section, thus guaranteeing an improved quality of the trapped cell images. Femtosecond laser micromachining emerges as a promising technique for the development of multifunctional integrated biophotonic devices that can be easily coupled to a microscope platform, thus enabling a complete characterization of the cells under test.

Toluidine blue-mediated photodynamic effects on staphylococcal biofilms.

Staphylococci are important causes of nosocomial and medical-device-related infections. Their virulence is attributed to the elaboration of biofilms that protect the organisms from immune system clearance and to increased resistance to phagocytosis and antibiotics. Photodynamic treatment (PDT) has been proposed as an alternative approach for the inactivation of bacteria in biofilms. In this study, we have investigated the effect of the photodynamic action of toluidine blue O (TBO) on the viability and structure of biofilms of Staphylococcus epidermidis and of a methicillin-resistant Staphylococcus aureus strain. Significant inactivation of cells was observed when staphylococcal biofilms were exposed to TBO and laser simultaneously. The effect was found to be light dose dependent. Confocal laser scanning microscopic study suggested damage to bacterial cell membranes in photodynamically treated biofilms. In addition, scanning electron microscopy provided direct evidence for the disruption of biofilm structure and a decrease in cell numbers in photodynamically treated biofilms. Furthermore, the treatment of biofilms with tetrasodium EDTA followed by PDT enhanced the photodynamic efficacy of TBO in S. epidermidis, but not in S. aureus, biofilms. The results suggest that photodynamic treatment may be a useful approach for the inactivation of staphylococcal biofilms adhering to solid surfaces of medical implants.

Linear and nonlinear optical properties of Hafnium-doped lithium-niobate crystals.

Measurements of birefringence, second-harmonic phase-matching conditions, and nonlinear coefficient d(31) are performed for a set of Hafnium-doped congruent lithium niobate (Hf:cLN) crystals as functions of dopant concentration. The data highlight that the threshold concentration, above which there is a change in the Hf incorporation mechanism, is slightly above 2mol% and that, up to this value of concentration, the efficiency of nonlinear processes is not affected by the dopant insertion. Combining these results with those already present in literature, Hf:cLN crystals appear to be very promising candidates for the development of photorefractivity-free wavelength converters working at room temperature.

Dispersive wave generation by solitons in microstructured optical fibers.

We study the nonlinear propagation of femtosecond pulses in the anomalous dispersion region of microstructured fibers, where soliton fission mechanisms play an important role. The experiment shows that the output spectrum contains, besides the infrared supercontinuum, a narrow-band 430-nm peak, carrying about one fourth of the input energy. By combining simulation and experiments, we explore the generation mechanism of the visible peak and describe its properties. The simulation demonstrates that the blue peak is generated only when the input pulse is so strongly compressed that the short-wavelength tail of the spectrum includes the wavelength predicted for the dispersive wave. In agreement with simulation, intensity-autocorrelation measurements show that the duration of the blue pulse is in the picosecond time range, and that, by increasing the input intensity, satellite pulses of lower intensity are generated.