Characterization of the Elastoplastic Response of Low Zn-Cu-Ti Alloy Sheets Using the CPB-06 Criterion.

Unlike other HCP metals such as titanium and magnesium, the behavior of zinc alloys has only been modeled in the literature. For the low Zn-Cu-Ti alloy sheet studied in this work, the anisotropy is clearly seen on the stress-strain curves and Lankford coefficients. These features impose a rigorous characterization and an adequate selection of the constitutive model to obtain an accurate representation of the material behavior in metal forming simulations. To describe the elastoplastic behavior of the alloy, this paper focuses on the material characterization through the application of the advanced Cazacu-Plunket-Barlat 2006 (CPB-06 for short) yield function combined with the well-known Hollomon hardening law. To this end, a two-stage methodology is proposed. Firstly, the material characterization is performed via tensile test measurements on sheet samples cut along the rolling, diagonal and transverse directions in order to fit the parameters involved in the associate CPB-06/Hollomon constitutive model. Secondly, these material parameters are assessed and validated in the simulation of the bulge test using different dies. The results obtained with the CPB-06/Hollomon model show a good agreement with the experimental data reported in the literature. Therefore, it is concluded that this model represents a consistent approach to estimate the behavior of Zn-Cu-Ti sheets under different forming conditions.

Numerical Simulation and Experimental Validation of Sheet Laser Forming Processes Using General Scanning Paths.

This work presents numerical simulations and an experimental validation of sheet laser forming processes using general scanning paths with different laser beam operating parameters (i.e., power, diameter, and scanning speed) in two specific graphite coated stainless steel blanks (i.e., with thicknesses of 0.3 mm and 0.6 mm for the AISI 302 and 304 alloys, respectively). To this end, three specific laser forming tests involving single S-shaped, multiple circular, and single piecewise linear scanning paths are carried out. On the other hand, the numerical simulation of these tests is performed via a coupled thermomechanical finite element formulation, accounting for large viscoplastic strains, temperature-dependent material properties, and convection-radiation phenomena. The final bending angles provided by this model are found to be in good agreement with the experimental measurements for all of the cases studied. Therefore, this modeling framework can be established as a reliable approach to predict the material thermomechanical response during sheet laser forming using general scanning paths.

Bending and pressurisation test of the human aortic arch: experiments, modelling and simulation of a patient-specific case.

This work presents experiments, modelling and simulation aimed at describing the mechanical behaviour of the human aortic arch during the bending and pressurisation test. The main motivation is to describe the material response of this artery when it is subjected to large quasi-static deformations in three different stages: bending, axial stretching and internal pressurisation. The sample corresponds to a young artery without cardiovascular pathologies. The pressure levels are within the normal and hypertension physiological ranges. The two principal findings of this work are firstly, the material characterisation performed via tensile test measurements that serve to derive the material parameters of a hyperelastic isotropic constitutive model and, secondly, the assessment of these material parameters in the simulation of the bending and pressurisation test. Overall, the reported material characterisation was found to provide a realistic description of the mechanical behaviour of the aortic arch under severe complex loading conditions considered in the bending and pressurisation test.

Mechanical characterisation of the human thoracic descending aorta: experiments and modelling.

This work presents experiments and modelling aimed at characterising the passive mechanical behaviour of the human thoracic descending aorta. To this end, uniaxial tension and pressurisation tests on healthy samples corresponding to newborn, young and adult arteries are performed. Then, the tensile measurements are used to calibrate the material parameters of the Holzapfel constitutive model. This model is found to adequately adjust the material behaviour in a wide deformation range; in particular, it captures the progressive stiffness increase and the anisotropy due to the stretching of the collagen fibres. Finally, the assessment of these material parameters in the modelling of the pressurisation test is addressed. The implication of this study is the possibility to predict the mechanical response of the human thoracic descending aorta under generalised loading states like those that can occur in physiological conditions and/or in medical device applications.