Your browser doesn't support javascript.
loading
Show: 20 | 50 | 100
Results 1 - 13 de 13
Filter
Add more filters










Publication year range
1.
Polymers (Basel) ; 16(10)2024 May 13.
Article in English | MEDLINE | ID: mdl-38794583

ABSTRACT

Carbon dots (CDs), owing to their excellent photoluminescent features, have been extensively studied for physics preparation methods and for biomedical and optoelectronic device applications. The assessment of the applicability of CDs in the production of luminescent polymeric composites used in LEDs, displays, sensors, and wearable devices is being pursued. The present study reports on an original, environmentally friendly, and low-cost route for the production of carbon dots with an average size of 4 nm by laser ablation in liquid. Jointly, to prove the significance of the study for a wide range of applications, a free-standing flexible polyvinyl alcohol (PVA) composite containing photoluminescent carbon dots was manufactured. CDs were prepared using targets of porose charcoal with a density of 0.271 g/cm3 placed in phosphate-buffered saline (PBS) liquid solution and irradiated for 30 min by pulsed IR diode laser. The optical properties of the obtained suspension containing carbon dots were studied with UV-ViS and FTIR spectroscopies. The photoluminescence of the produced carbon dots was confirmed by the emission peak at 480 nm in the luminescence spectrum. A narrow luminescence band with a full width at half-maximum (FWHM) of less than 40 nm could be an asset in spectral emission analysis in different applications. Atomic force microscopy confirms the feasibility of manufacturing CDs in clean and biocompatible environments, paving the way for an easier and faster production route, crucial for their wider applicability.

2.
Micromachines (Basel) ; 14(7)2023 Jun 24.
Article in English | MEDLINE | ID: mdl-37512610

ABSTRACT

Cyclic olefin copolymer (COC) is a novel type of thermoplastic polymer gaining the attention of the scientific community in electronic, optoelectronic, biomedicine and packaging applications. Despite the benefits in the use of COC such as undoubted optical transparency, chemical stability, a good water-vapor barrier and biocompatibility, its original hydrophobicity restricts its wider applicability and optimization of its performances. Presently, we report on the optical and morphological properties of the films of COC covered with Ti in selected areas. The layer of Ti on COC was deposited by pulsed lased deposition processing. The Ti/COC film was characterized by UV-Vis spectroscopy indicating that its transmittance in the visible region decreased by about 20% with respect to the pristine polymer. The quality of the deposited Ti was assessed with the morphology by scanning electron (SEM) and atomic force microscopies (AFM). The modification of the wettability was observed by the sessile drop method indicating a reduction of the native hydrophilicity.

3.
Micromachines (Basel) ; 14(4)2023 Apr 02.
Article in English | MEDLINE | ID: mdl-37421045

ABSTRACT

SiC detectors based on a Schottky junction represent useful devices to characterize fast laser-generated plasmas. High-intensity fs lasers have been used to irradiate thin foils and to characterize the produced accelerated electrons and ions in the target normal sheath acceleration (TNSA) regime, detecting their emission in the forward direction and at different angles with respect to the normal to the target surface. The electrons' energies have been measured using relativistic relationships applied to their velocity measured by SiC detectors in the time-of-flight (TOF) approach. In view of their high energy resolution, high energy gap, low leakage current, and high response velocity, SiC detectors reveal UV and X-rays, electrons, and ions emitted from the generated laser plasma. The electron and ion emissions can be characterized by energy through the measure of the particle velocities with a limitation at electron relativistic energies since they proceed at a velocity near that of the speed of light and overlap the plasma photon detection. The crucial discrimination between electrons and protons, which are the fastest ions emitted from the plasma, can be well resolved using SiC diodes. Such detectors enable the monitoring of the high ion acceleration obtained using high laser contrast and the absence of ion acceleration using low laser contrast, as presented and discussed.

4.
Polymers (Basel) ; 15(5)2023 Feb 21.
Article in English | MEDLINE | ID: mdl-36904307

ABSTRACT

In this study, novel flexible micro-scale humidity sensors were directly fabricated in graphene oxide (GO) and polyimide (PI) using ion beam writing without any further modifications, and then successfully tested in an atmospheric chamber. Two low fluences (3.75 × 1014 cm-2 and 5.625 × 1014 cm-2) of carbon ions with an energy of 5 MeV were used, and structural changes in the irradiated materials were expected. The shape and structure of prepared micro-sensors were studied using scanning electron microscopy (SEM). The structural and compositional changes in the irradiated area were characterized using micro-Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), Rutherford back-scattering spectroscopy (RBS), energy-dispersive X-ray spectroscopy (EDS), and elastic recoil detection analysis (ERDA) spectroscopy. The sensing performance was tested at a relative humidity (RH) ranging from 5% to 60%, where the electrical conductivity of PI varied by three orders of magnitude, and the electrical capacitance of GO varied in the order of pico-farads. In addition, the PI sensor has proven long-term sensing stability in air. We demonstrated a novel method of ion micro-beam writing to prepare flexible micro-sensors that function over a wide range of humidity and have good sensitivity and great potential for widespread applications.

5.
Polymers (Basel) ; 15(5)2023 Feb 25.
Article in English | MEDLINE | ID: mdl-36904413

ABSTRACT

Thin sheets of ultra-high molecular weight polyethylene (UHMWPE), both in pristine form and containing carbon nanotubes (CNTs) or Fe2O3 nanoparticles (NPs) at different concentrations, were prepared. The CNT and Fe2O3 NP weight percentages used ranged from 0.01% to 1%. The presence of CNTs and Fe2O3 NPs in UHMWPE was confirmed by transmission and scanning electron microscopy and by energy dispersive X-ray spectroscopy analysis (EDS). The effects of the embedded nanostructures on the UHMWPE samples were studied using attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy and UV-Vis absorption spectroscopy. The ATR-FTIR spectra show the characteristic features of the UHMWPE, CNTs, and Fe2O3. Concerning the optical properties, regardless of the type of embedded nanostructures, an increase in the optical absorption was observed. The allowed direct optical energy gap value was determined from the optical absorption spectra: in both cases, it decreases with increasing CNT or Fe2O3 NP concentrations. The obtained results will be presented and discussed.

6.
Micromachines (Basel) ; 14(2)2023 Jan 22.
Article in English | MEDLINE | ID: mdl-36837984

ABSTRACT

Polymer membranes are conventionally prepared using high-energy particles from radioactive decay or by the bombardment of hundreds of MeVs energy ions. In both circumstances, tracks of damage are produced by particles/ions passing through the polymer, and successively, the damaged material is removed by chemical etching to create narrow pores. This process ensures nanosized pore diameter but with random placement, leading to non-uniform local pore density and low membrane porosity, which is necessary to reduce the risk of their overlapping. The present study is focused on the use of polyethylene terephthalate (PET) foils irradiated by 10.0 MeV carbon ions, easily achievable with ordinary ion accelerators. The ion irradiation conditions and the chemical etching conditions were monitored to obtain customized pore locations without pore overlapping in PET. The quality, shape, and size of the pores generated in the micromembranes can have a large impact on their applicability. In this view, the Scanning Transmission Ion Microscopy coupled with a computer code created in our laboratory was implemented to acquire new visual and quantitative insights on fabricated membranes.

7.
Nanomaterials (Basel) ; 12(22)2022 Nov 08.
Article in English | MEDLINE | ID: mdl-36432215

ABSTRACT

Routinely, in membrane technology, the decay from radioactive particles or the bombardment of ions with MeV energy per nucleon have been employed for the production of narrow and long pores in membranes. Presently, the ion lithography is proposed to make the fabrication cost more affordable. It is prospective for the use of medium capacity accelerators making more feasible the fabrication of customized membranes. Thin polyethylene terephthalate foils have been patterned using 12 MeV O5+ ions and then processed to obtain good aspect ratio ion track pores in membranes. Pores of micrometric diameter with the following profiles were fabricated in the membranes: truncated cone, double conical, ideal cone, and cylindrical. Monitoring of the shape and size of pores has been attempted with a combination of Scanning Transmission Ion Microscope and a newly designed simulation program. This study is focused on the use of low-energy ions, accomplished in all laboratories, for the fabrication of membranes where the pores are not randomly traced and exhibit higher surface density and negligible overlapping than in membranes commonly manufactured. The good reproducibility and the ordered pore locations can be potentially utilized in applications such as microfluidics and organ-on-chip microsystems, where cells growing over porous substrates are used in simulation of biological barriers and transport processes.

8.
Int J Mol Sci ; 23(20)2022 Oct 19.
Article in English | MEDLINE | ID: mdl-36293417

ABSTRACT

In the present study, graphene oxide foils 10 µm thick have been irradiated in vacuum using same charge state (one charge state) ions, such as protons, helium and oxygen ions, at the same energies (3 MeV) and fluences (from 5 × 1011 ion/cm2 to 5 × 1014 ion/cm2). The structural changes generated by the ion energy deposition and investigated by X-ray diffraction have suggested the generation of new phases, as reduced GO, GO quantum dots and graphitic nanofibers, carbon nanotubes, amorphous carbon and stacked-cup carbon nanofibers. Further analyses, based on Rutherford Backscattering Spectrometry and Elastic Recoil Detection Analysis, have indicated a reduction of GO connected to the atomic number of implanted ions. The morphological changes in the ion irradiated GO foils have been monitored by Transmission Electron, Atomic Force and Scanning Electron microscopies. The present study aims to better structurally, compositionally and morphologically characterize the GO foils irradiated by different ions at the same conditions and at very low ion fluencies to validate the use of GO for radiation detection and propose it as a promising dosimeter. It has been observed that GO quantum dots are produced on the GO foil when it is irradiated by proton, helium and oxygen ions and their number increases with the atomic number of beam gaseous ion.


Subject(s)
Nanotubes, Carbon , Protons , Helium , Ions , Oxygen
9.
Phys Chem Chem Phys ; 24(10): 6290-6301, 2022 Mar 09.
Article in English | MEDLINE | ID: mdl-35230368

ABSTRACT

The structural differences in (100)-, (110)- and (111)-oriented cubic yttria-stabilised zirconia (YSZ) single crystals after implantation with 2 MeV Si+ ions at the fluences of 5 × 1015, 1 × 1016 and 5 × 1016 cm-2 were studied using Rutherford backscattering spectrometry in the channelling mode (RBS-C), X-ray diffraction (XRD) and Raman spectroscopy. The RBS-C results show that the damage accumulation in the 〈110〉 direction exhibits a lower level of disorder (<0.3) than the other orientations (<0.6) and it seems that the (110) crystallographic orientation is the most resistant to radiation damage. The experimental results from the RBS measurement were compared with the results from the XRD measurements. The XRD data were analysed using the standard two-beam dynamical X-ray diffraction theory and the pure isotropic strain was deduced from the fit for the fluence of 5 × 1015 cm-2. It was shown that the maximum value of the isotropic strain does not depend on the surface orientation. The increase in signal intensity at ∼689 cm-1 is probably related to an increase in implantation defects such as oxygen vacancies.

10.
Int J Mol Sci ; 22(22)2021 Nov 10.
Article in English | MEDLINE | ID: mdl-34830035

ABSTRACT

Typically, polymeric composites containing nanoparticles are realized by incorporating pre-made nanoparticles into a polymer matrix by using blending solvent or by the reduction of metal salt dispersed in the polymeric matrix. Generally, the production of pre-made Au NPs occurs in liquids with two-step processes: producing the gold nanoparticles first and then adding them to the liquid polymer. A reproducible method to synthetize Au nanoparticles (NPs) into polydimethylsiloxane (PDMS) without any external reducing or stabilizing agent is a challenge. In this paper, a single-step method is proposed to synthetize nanoparticles (NPs) and at the same time to realize reproducible porous and bulk composites using laser ablation in liquid. With this single-step process, the gold nanoparticles are therefore produced directly in the liquid polymer. The optical properties of the suspensions of AuNPs in distilled water and in the curing agent have been analyzed by the UV-VIS spectroscopy, employed in the transmission mode, and compared with those of the pure curing agent. The electrical dc conductivity of the porous PDMS/Au NPs nanocomposites has been evaluated by the I-V characteristics. Scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) analysis have monitored the composition and morphology of the so-obtained composites and the size of the fabricated Au nanoparticles. Atomic force microscopy (AFM) has been used to determine the roughness of the bulk PDMS and its Au NP composites.


Subject(s)
Dimethylpolysiloxanes/chemistry , Gold/chemistry , Laser Therapy , Metal Nanoparticles/chemistry , Nanocomposites/chemistry , Porosity
12.
Rev Sci Instrum ; 90(1): 013701, 2019 Jan.
Article in English | MEDLINE | ID: mdl-30709223

ABSTRACT

The Tandetron Laboratory of the Nuclear Physics Institute of the Czech Academy of Sciences is equipped with five beam lines associated with a 3 MV tandem electrostatic accelerator model 4130 MC from High Voltage Engineering Europa B.V. This accelerator is coupled with two duoplasmatron sources and a single sputter ion source and provides ions from hydrogen to gold. One of these lines is a nuclear microbeam facility, utilizing ion beams of micro- and sub-micro sizes for materials research by use of particle induced x-ray emission spectroscopy, particle induced gamma emission, Rutherford back-scattering spectroscopy, and scanning transmission ion microscopy methods as well as for ion beam writing. The major advantage of the presented microprobe is a possibility of 3D structure creation not only in polymer materials using light ions but also in other materials such as glass, ceramics, etc. by use of heavy ions. The focusing system allows focusing of charged particles with a maximum rigidity of 11 MeV amu/q2. The usual resolution in high and low current modes is 2 × 3 µm2 for a 100 pA and 0.3 × 0.5 µm2 for the 2000 ions/s of 2 MeV protons, respectively. A detailed facility description is given in the paper. The applications of focused beams of heavy ions as well as examples of light ions utilizing are also presented in the article.

13.
Phys Chem Chem Phys ; 19(16): 10282-10291, 2017 Apr 19.
Article in English | MEDLINE | ID: mdl-28379227

ABSTRACT

In this paper, the effect of light ion irradiation on graphene oxide foil structure and composition was studied. Due to the excellent properties of graphene based materials suitable for application in electronics, optoelectronics, micro-mechanics and space technologies, the interaction of energetic ions with graphene based structures is worth studying. From the fundamental point of view, it is also interesting to get information about graphene oxide structure modification and the possible functional properties after irradiation by energetic ions. The light ion irradiation of graphene oxide (GO) foil was performed using 2.5 MeV H+ and 5.1 MeV He2+ ions. The change in the elemental composition of the GO foils after ion irradiation was investigated using Rutherford Backscattering Spectrometry and Elastic Recoil Detection Analysis. The influence of ion irradiation was further studied by microscopy methods. The chemical composition and structural changes of the GO foil surface were characterized by spectroscopy techniques including XPS, FTIR and Raman spectroscopy. Although the results of ion beam analysis indicated no significant compositional changes in the bulk of GO foils connected to ion irradiation, XPS, ATR-FTIR and Raman spectroscopy revealed reduction and removal of oxygen functionalities on the surface of graphene oxide. This reduction leads to a surface resistivity decrease after ion irradiation dependent on the ion species, fluence and energy.

SELECTION OF CITATIONS
SEARCH DETAIL
...