Effects of Manufacturing and Finishing Techniques of Feldspathic Ceramics on Surface Topography, Biofilm Formation, and Cell Viability for Human Gingival Fibroblasts.

PURPOSE:: Feldspathic ceramic restorations can be obtained by different techniques (stratification or computer-aided design/computer-aided manufacturing [CAD/CAM] blocks) and finishing procedures (polishing or glaze application). This study evaluated the effects of techniques and finishing procedures on surface properties, biofilm formation, and viability of human gingival fibroblasts (FMM-1) in contact with these materials. METHODS AND MATERIALS:: Ceramic specimens were obtained through a stratification technique (Vita VM9) and from CAD/CAM blocks (Vita Blocs Mark II; both Vita Zahnfabrik) and their surfaces were finished by polishing (ceramisté diamond rubbers + polishing paste; "p" subgroups) or glaze spray application + sintering ("g" subgroups). Roughness (Ra and RSm parameters) and surface free energy (SFE) were measured. Early biofilm formation of Streptococcus mutans, Streptococcus sanguinis, and Candida albicans was evaluated by counting colony-forming units (CFU). MTT (3-[4.5-dimethyl-thiazol-2-yl-]-2.5-diphenyl tetrazolium bromide) cytotoxicity test evaluated cellular viability for the growth of FMM-1 after 24 hours and seven days of contact. Scanning electron microscopy (SEM) and three-dimensional optical profilometry were performed to qualitatively analyze the surface. Data were analyzed by analysis of variance, Tukey test, and t-test (all α=0.05). RESULTS:: Polished samples presented lower roughness (Ra, p=0.015; RSm, p=0.049) and higher SFE ( p=0.00). Streptococci had higher CFU in all groups, but the CFU of C albicans was lower for polished samples. Biofilm formation was influenced by the interaction of all factors ( p=0.018), and the materials showed no cytotoxicity to FMM-1 growth. CONCLUSIONS:: Polishing resulted in the lowest values for surface roughness and higher SFE values. Polished ceramics showed less C albicans adherence while the adherence of Streptococci was greater than C albicans in all conditions.

Monolithic Ceramics: Effect of Finishing Techniques on Surface Properties, Bacterial Adhesion and Cell Viability.

INTRODUCTION: This study evaluated the morphology, biofilm formation, and viability of human gingival fibroblasts in contact with two monolithic ceramics after two different finishing techniques: polishing or glazing. For this, 92 blocks (4.5 × 4.5 × 1.5 mm) of each ceramic were made using high translucency zirconia partially stabilized by yttrium (YZHT) and lithium silicate reinforced by zirconium (ZLS). METHODS AND MATERIALS: Blocks were sintered and then divided into glazing (g) or polishing (p) surface finish. Surface roughness (Ra and RSm) was evaluated through a contact rugosimeter and profilometry. Specimens were contaminated for heterotypic biofilm formation with Streptococcus mutans, Streptococcus sanguinis and Candida albicans for 16 hours. Biofilm was quantified by counting the colony forming units (CFU/mL) and analyzed by scanning electron microscopy (SEM). Fibroblast viability was evaluated by MTT assay. Surface free energy (SFE) was also determined. Roughness data were evaluated using nonparametric tests, while SFE, MTT and CFU results were evaluated by analysis of variance and Tukey test, and MTT data were also submitted to t-test (all, α=0.05). RESULTS: Results showed that polished samples presented a lower high profile mean ( p<0.001); however, YZHTg presented less space between defects ( p=0.0002). SFE showed that YZHT presented higher SFE than ZLS. Profilometry evidenced more homogeneity on polished surfaces. The interaction of finishing technique and microorganisms influenced the CFU ( p=0.00). MTT assay demonstrated initial severe cytotoxic behavior for polished surfaces. SEM images showed homogeneous surfaces, except for glazed YZHT. CONCLUSION: Glazed surfaces have a greater roughness and tend to accumulate more biofilm. Polished surfaces have higher SFE; however, they are temporarily cytotoxic.