Structure of Complex Concentrated Alloys Derived from Iron Aluminide Fe3Al.

The phase structure and composition of a series of four alloys based on Fe3Al was investigated by means of scanning electron microscopy, X-ray diffraction and transmission electron microscopy. The materials were composed of Fe and Al with a fixed ratio of 3:1 alloyed with V, Cr and Ni at 8, 12, 15 and 20 at. % each (composition formula: Fe3(100-3x)/4 Al(100-3x)/4VxCrxNix). For 8% alloying, the material is single-phase D03. Furthermore, 12 and 15% alloying results in bcc-B2 phase separation on two length scales. Moreover, 20% alloying gives rise to the FeNiCrV σ phase supplemented by B2. These findings are discussed with respect to the results obtained via Calphad modeling using the TCHEA5 database and can serve in further improvement.

CePt2Al2: Structural and Bulk Properties.

This work is focused on the structural and physical properties of CePt2Al2, an intermetallic compound. At room temperature, the modulated orthorhombic structure Cmme(a00)000, with q→= (0.481, 0, 0) has been determined by single-crystal X-ray diffraction supplemented by dependence of lattice parameters above room temperature for which the X-ray powder diffraction was used. The compound undergoes a structural transition to a tetragonal structure above room temperature. This transition exhibits 50 °C hysteresis and creates a domain structure in the sample. The magnetic behavior has been studied by specific heat, magnetization, and transport measurements in the temperature range between 0.5 and 300 K. Specific heat and susceptibility shows an antiferromagnetic order below 2 K. On the basis of electrical resistivity and other bulk measurements, CePt2Al2 can be considered a Kondo lattice material. The presence of a modulated crystal structure opens the possibility of a charge density wave state in CePt2Al2 as observed for (Re)Pt2Si2.

Growth of a TiNb adhesion interlayer for bioactive coatings.

Surface bioactivity has been under intensive study with reference to its use in medical implants. Our study is focused on coatings prepared from an electroactive material which can support bone cell adhesion. Until now, hydroxyapatite films have usually been utilized as a chemically-active surface agent. However, electrically-active films could set a new direction in hard tissue replacement. As a base for these films, it is necessary to prepare an intermediate film, which can serve as a suitable barrier against the possible diffusion of some allergens and toxic elements from the substrate. The intermediate film also improves the adaptation of the mechanical properties of the basic material to an electroactive film. The aim of our work was to select an implantable and biocompatible material for this intermediate film that is suitable for coating several widely-used materials, to check the possibility of preparing an electroactive film for use on a material of this type, and to characterize the structure and several mechanical properties of this intermediate film. TiNb was selected as the material for the intermediate film, because of its excellent chemical and mechanical properties. TiNb coatings were deposited by magnetron sputtering on various substrates, namely Ti, Ti6Al4V, stainless steel, and bulk TiNb (as standard), and important properties of the layers, e.g. surface morphology and surface roughness, crystalline structure, etc., were characterized by several methods (SEM, EBSD, X-ray diffraction, nanoindentation and roughness measurement). It was found that the structure and the mechanical properties of the TiNb layer depended significantly on the type of substrate. TiNb was then used as a substrate for depositing a ferroelectrically active material, e.g., BaTiO3, and the adhesion, viability and proliferation of human osteoblast-like Saos-2 cells on this system were studied. We found that the electroactive BaTiO3 film was not only non-cytotoxic (i.e. it did not affect the cell viability). It also enhanced the growth of Saos-2 cells in comparison with pure TiNb and with standard tissue culture polystyrene wells, and also in comparison with BaTiO3 films deposited on Ti, i.e. a material clinically used for implantation into the bone.

Microstructure, Optical and Photocatalytic Properties of TiO2 Thin Films Prepared by Chelating-Agent Assisted Sol-Gel Method.

Single and multilayer TiO2 thin films coated on two types of soda-lime glass substrates (microscope slides and cylinders) were prepared by a chelating agent-assisted sol-gel method, using ethyl acetoacetate as a chelating agent, dip-coating and calcination at 500 °C for 2 h in air. Phase composition, microstructural, morphological and optical properties of thin films were comprehensively investigated by using XRF, advanced XRD analysis, Raman and UV-vis spectroscopy and AFM. It was found out that the thickness of thin films increases linearly with increasing number of deposited layers, indicating a good adhesion of the titania solution to a glass substrate as well as to a previously calcined layer. 1 layer film crystallized to anatase-TiO2(B) mixture with minor/negligible amount of nanosized brookite, 2-4 layers films crystallized to anatase-brookite-TiO2(B) mixture. In contrast to other multilayers films, 4 layers film was highly inhomogeneous. The different phase composition of thin films was clarified based on the crystallization via titanate/s and metastable monoclinic TiO2(B) as a consequence of several phenomena; the diffusion of Na⁺ ions from a soda-lime glass substrate, acidic conditions and repeated thermal treatment. The multilayer films were in average highly transparent (80-95%) in the visible light region with the sharp absorption edge in the UV light region. Additionally, the photocatalytic properties of selected multilayer films were compared in AO7 photodegradation. Photocatalytic experiments showed that thicker 4 layers film of tricrystalline anatase-brookite-TiO2(B) phase mixture was similarly active as thinner 3 layers film of similar phase composition, which may be a consequence of the inhomogeneity of the thicker film.