Toward low-loss mid-infrared Ga2O3-BaO-GeO2 optical fibers.

The development of efficient and compact photonic systems in support of mid-infrared integrated optics is currently facing several challenges. To date, most mid-infrared glass-based devices are employing fluoride or chalcogenide glasses (FCGs). Although the commercialization of FCGs-based optical devices has rapidly grown during the last decade, their development is rather cumbersome due to either poor crystallization and hygroscopicity resilience or poor mechanical-thermal properties of the FCGs. To overcome these issues, the parallel development of heavy-metal oxide optical fiber from the barium-germanium-gallium oxide vitreous system (BGG) has revealed a promising alternative. However, over 30 years of fiber fabrication optimization, the final missing step of drawing BGG fibers with acceptable losses for meters-long active and passive optical devices had not yet been reached. In this article, we first identify the three most important factors that prevent the fabrication of low-loss BGG fibers i.e., surface quality, volumic striae and glass thermal-darkening. Each of the three factors is then addressed in setting up a protocol enabling the fabrication of low-loss optical fibers from gallium-rich BGG glass compositions. Accordingly, to the best of our knowledge, we report the lowest losses ever measured in a BGG glass fiber i.e., down to 200 dB km-1 at 1350 nm.

Response of Various Yb3+-Doped Oxide Glasses to Different Radiation Treatments.

The radiation effects of electrons and protons on the spectroscopic and optical properties of oxide glasses doped with Yb3+ in various glass systems were investigated to understand the impact of the glass composition on the glass photo-response. Changes in the optical and emission properties were seen after the radiation treatment, and the magnitude of the changes depended on the irradiation source and dose. For all the investigated materials, the absorption coefficients in the 200-550 nm range increase post-irradiation, revealing the formation of defects in the glasses during the irradiation. While the spectroscopic properties of the tellurite glass remain unchanged, a small reduction in the Yb3+ emission intensity was seen after irradiating the phosphate, borosilicate, and germanate glasses, indicating that a reduction of Yb3+ to Yb2+ might occur in these glasses during the radiation treatment. The changes in the optical and spectroscopic properties after proton irradiation are small as they are localized at the surface of the glasses due to the shallow penetration depth of the proton in the glass. Even though the doses are small, the electron irradiation produces larger changes in the optical and spectroscopic properties since the electrons penetrate the entire volume of the glasses. All the changes in the optical and spectroscopic properties of the glasses were successfully reversed after a short heat treatment revealing the reversible nature of the photo-response of the investigated glasses.

Spatial beam reshaping and large-band nonlinear conversion in rectangular-core phosphate glass fibers.

Here we present the ability of Nd3+-doped zinc-phosphate glasses to be shaped into rectangular core fibers. At first, the physico-chemical properties of the developed P2O5-based materials are investigated for different concentrations of neodymium oxide and core and cladding glass compositions are selected for further fiber development. A modified stack-and-draw technique is used to produce multimode large rectangular-core optical fibers. Self-guided nonlinear effects acting as spatial beam reshaping processes occurring in these newly-developed photonic structures lead to the generation of spectral broadenings in the visible and near-infrared spectral domains.

Inorganic Thermoelectric Fibers: A Review of Materials, Fabrication Methods, and Applications.

Thermoelectric technology can directly harvest the waste heat into electricity, which is a promising field of green and sustainable energy. In this aspect, flexible thermoelectrics (FTE) such as wearable fabrics, smart biosensing, and biomedical electronics offer a variety of applications. Since the nanofibers are one of the important constructions of FTE, inorganic thermoelectric fibers are focused on here due to their excellent thermoelectric performance and acceptable flexibility. Additionally, measurement and microstructure characterizations for various thermoelectric fibers (Bi-Sb-Te, Ag2Te, PbTe, SnSe and NaCo2O4) made by different fabrication methods, such as electrospinning, two-step anodization process, solution-phase deposition method, focused ion beam, and self-heated 3ω method, are detailed. This review further illustrates that some techniques, such as thermal drawing method, result in high performance of fiber-based thermoelectric properties, which can emerge in wearable devices and smart electronics in the near future.

Transparent Glasses and Glass-Ceramics in the Ternary System TeO2-Nb2O5-PbF2.

Transparent fluorotellurite glasses were prepared by melt-quenching in the ternary system TeO2-Nb2O5-PbF2. The synthesis conditions were adjusted to minimize fluorine loss monitored as HF release. It was found that 10 mol% of Nb2O5 is the optimum content for PbF2 incorporation up to 35 mol% in the tellurite matrix without loss of glass forming ability. Such glass compositions exhibit a wide optical window from 380 nm to about 6 µm. Crystallization properties were carefully investigated by thermal analysis and compositions with higher PbF2 contents exhibit preferential precipitation of lead oxyfluoride Pb2OF2 at lower temperatures. The lead oxyfluoride crystallization mechanism is also governed by a volume nucleation, barely reported in tellurite glasses. Eu3+ doping of these glass compositions also promotes a more efficient nucleation step under suitable heat-treatments, resulting in transparent Eu3+-doped glass-ceramics whereas undoped glass-ceramics are translucent. Finally, Eu3+ spectroscopy pointed out a progressive, more symmetric surrounding around the rare earth ions with increasing PbF2 contents as well as higher quantum efficiencies. These new fluorotellurite glass compositions are promising as luminescent hosts working in the middle infrared.

Radiation-Induced Defects and Effects in Germanate and Tellurite Glasses.

This review focuses on the radiation-induced changes in germanate and tellurite glasses. These glasses have been of great interest due to their remarkable potential for photonics, in terms of extended transmission window in the mid-infrared, ability of rare-earth loading suitable with a laser, and amplification in the near- and mid-infrared or high nonlinear optical properties. Here, we summarize information about possible radiation-induced defects, mechanisms of their formation, and the influence of the glass composition on this process. Special attention is paid to laser-induced structural modification of these glasses, including possible mechanisms of the laser-glass interaction, laser-induced crystallization, and waveguide writing. It is shown that these methods can be used for photostructuring of the glass and have great potential for practical applications.

Optical Emission Detector Based on Plasma Discharge Generation at the Tip of a Multimaterial Fiber.

Experimental development of a compact optical emission detector based on the assembly of a polymer-metal and a standard silica fiber is presented in this paper. This device is exploited in a proof-of-principle experiment for gas detection application by means of plasma spectroscopy in the visible-Near Infrared spectral region. A multimode fiber (MMF) is associated with a functional hollow dual-electrodes elongated structure fabricated by the direct preform-to-fiber homothetic co-drawing. A potential of 1.5 kV is applied between the two electrodes embedded inside the composite cladding, which generates an atmospheric pressure dc glow discharge at the tip of the fiber bundle. The emitted light is then collected by the MMF for optical diagnostics. Probing of different atmospheres is presented at the end of this study.

Direct laser writing of a new type of waveguides in silver containing glasses.

Direct laser writing in glasses is a growing field of research in photonics since it provides a robust and efficient way to directly address 3D material structuring. Generally, direct laser writing in glasses induces physical modifications such as refractive index changes that have been classified under three different types (Type I, II & III). In a silver-containing zinc phosphate glass, direct laser writing additionally proceeds via the formation of silver clusters at the periphery of the interaction voxel. In this paper, we introduce a novel type of refractive index modification based on the creation of the photo-induced silver clusters allowing the inscription of a new type of optical waveguides. Various waveguides as well as a 50-50 beam splitter were written inside bulk glasses and characterized. The waveguiding properties observed in the bulk of such silver-containing glass samples were further transposed to ribbon shaped fibers made of the same material. Our results pave the way for the fabrication of 3D integrated circuits and fiber sensors with original fluorescent, nonlinear optical and plasmonic properties. The universality of these new findings should further extend in any silver-containing glasses that show similar laser-induced behavior in terms of silver cluster production.

Mid-infrared materials and devices on a Si platform for optical sensing.

In this article, we review our recent work on mid-infrared (mid-IR) photonic materials and devices fabricated on silicon for on-chip sensing applications. Pedestal waveguides based on silicon are demonstrated as broadband mid-IR sensors. Our low-loss mid-IR directional couplers demonstrated in SiN x waveguides are useful in differential sensing applications. Photonic crystal cavities and microdisk resonators based on chalcogenide glasses for high sensitivity are also demonstrated as effective mid-IR sensors. Polymer-based functionalization layers, to enhance the sensitivity and selectivity of our sensor devices, are also presented. We discuss the design of mid-IR chalcogenide waveguides integrated with polycrystalline PbTe detectors on a monolithic silicon platform for optical sensing, wherein the use of a low-index spacer layer enables the evanescent coupling of mid-IR light from the waveguides to the detector. Finally, we show the successful fabrication processing of our first prototype mid-IR waveguide-integrated detectors.

Demonstration of mid-infrared waveguide photonic crystal cavities.

We have demonstrated what we believe to be the first waveguide photonic crystal cavity operating in the mid-infrared. The devices were fabricated from Ge23Sb7S70 chalcogenide glass (ChG) on CaF2 substrates by combing photolithographic patterning and focused ion beam milling. The waveguide-coupled cavities were characterized using a fiber end fire coupling method at 5.2 µm wavelength, and a loaded quality factor of ~2000 was measured near the critical coupling regime.

Demonstration of high-Q mid-infrared chalcogenide glass-on-silicon resonators.

We demonstrated high-index-contrast, waveguide-coupled As2Se3 chalcogenide glass resonators monolithically integrated on silicon fabricated using optical lithography and a lift-off process. The resonators exhibited a high intrinsic quality factor of 2×10(5) at 5.2 µm wavelength, which is among the highest values reported in on-chip mid-infrared (mid-IR) photonic devices. The resonator can serve as a key building block for mid-IR planar photonic circuits.

Resolving optical illumination distributions along an axially symmetric photodetecting fiber.

Photodetecting fibers of arbitrary length with internal metal, semiconductor and insulator domains have recently been demonstrated. These semiconductor devices exhibit a continuous translational symmetry which presents challenges to the extraction of spatially resolved information. Here, we overcome this seemingly fundamental limitation and achieve the detection and spatial localization of a single incident optical beam at sub-centimeter resolution, along a one-meter fiber section. Using an approach that breaks the axial symmetry through the constuction of a convex electrical potential along the fiber axis, we demonstrate the full reconstruction of an arbitrary rectangular optical wave profile. Finally, the localization of up to three points of illumination simultaneously incident on a photodetecting fiber is achieved.

Fiber field-effect device via in situ channel crystallization.

The in situ crystallization of the incorporated amorphous semiconductor within the multimaterial fiber device yields a large decrease in defect density and a concomitant five-order-of-magnitude decrease in resistivity of the novel metal-insulator-crystalline semiconductor structure. Using a post-drawing crystallization process, the first tens-of-meters-long single-fiber field-effect device is demonstrated. This work opens significant opportunities for incorporating higher functionality in functional fibers and fabrics.